KTM Front Wheel Bearing Installation Manuals

0

Filed Under (KTM) by admin on 31-01-2012

download
1 Place motorcycle on a stand so that the front wheel is off the ground. 2 Using a 27mm socket remove the front axle nut. Using a 10mm socket, loosen the four front axle pinch bolts. Slide front axle out of forks and remove front wheel. 3 Insert a long punch (with a good square edge) into the center of the aluminum wheel bearing spacers and push up against the inner edge of the spacer on the opposite side of the wheel (Fig. 1). Using a hammer, tap the punch around the entire circumference of the spacer until it completely slides out of the bearing (Fig. 2). Turn the wheel over and remove the other spacer in the same way. 4 Use a long screwdriver or narrow pry bar and pry the seals out of each side of the wheel (Fig. 3). 5 Using snap ring pliers, remove the bearing retaining snap ring from the brake rotor side of the wheel. (Fig. 4) NOTE: 2003 – CURRENT MODELS USING # 16-092 KIT DO NOT USE THIS SNAP RING. 6 Insert a long punch (with a good square edge) into the center of the wheel bearing, and push up against the inner edge of the bearing on the opposite side of the wheel. Using a hammer, tap the punch around the entire circumference of the bearing until it completely slides out of the hub. Turn the wheel over and remove the other bearing in the same way. NOTE: It may be necessary to tap on the punch sideways at first to knock the center aluminum sleeve off center so that you are able to get the punch on the edge of the bearing. 7 Clean areas where bearings will be inserted back into hub and apply a thin coat of grease around the machined hub surface. Tap the bearing on the snap ring (if used, either side if not) side of the hub into the machined hub surface, making sure to keep it square with the hub as it goes in and only tap on the outer race of the bearing. Once you get the bearing flush with the outer edge of the hub, use a socket or piece of pipe that is just smaller than the outside diameter of the bearing to finish tapping the bearing into the hub. (Fig. 5) 8 Install the bearing retainer snap ring (if used) into the groove machined in the hub, and then tap the seal in place over the snap ring with the spring on the seal in towards the center of the wheel. Tap in the aluminum spacer in the center of the seal.

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

HARLEY DAVIDSON REAR SLOTTED SIX-SPOKE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. NOTE Install long valve stem (43206-01) included in the installation kit. Discard all other valve stems. 2. See Figure 1. Install valve stem assembly (I) on wheel. Refer to TIRES in service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) NOTE For Kits 43928-08 and 43929-08: When installing wheel on 2008 and later XL models, install bearing shim from installation kit under the primary bearing. For Kits 43934-07, 43942-07 and 43972-07: When installing wheel on 2008 and later Dyna models, install bearing shim from installation kit under the primary bearing. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. NOTES The valve stem side of the wheel and machined grooves in the hub face indicate the primary bearing side. Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR ROAD WINDER WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 1 and Service Parts Tables. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to the service manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from you dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to the service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the appropriate service parts table. Refer to the service manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle and stock spacers to motorcycle. Refer to the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

Incoming search terms:

HARLEY DAVIDSON FRONT DETONATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Discard moon-style hub cap on FLSTC and FLSTN models. Discard left side spacer on FXSTS models and tapered spacer on FXSTD models. Refer to FRONT WHEEL in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTE Install primary bearing first using the applicable Service Manual and WHEEL BEARING REMOVER/INSTALLER. Kit 44550-07: The left side of the wheel has a groove machined in the hub to identify it as the disc side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kits 44660-07 and 44661-07: The wheel should be installed so that the hub markings are on the left side of the motorcycle. An arrow engraved into the rim of 44661-07 indicates the direction of rotation. A groove is machined in the left-side hub face to indicate the primary bearing side. • Dual-disc models: Install the brake discs according to the Service Manual procedures. The Chrome hub cap (2) is not used. • Single-disc models: Install the brake disc according to the Service Manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Kit 44660-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 21-inch wheels. Kit 44661-07: The gross axle weight rating is unaffected by the installation of this wheel on a vehicle originally equipped with 19-inch wheels. Kit 44552-08: The left side of the wheel has a groove machined in the hub to identify it as the left side for installation, as well as the primary bearing side. The wheel should be installed so that the valve stem is on the right side of the motorcycle. Kit 44556-07: The right side of the wheel has a groove machined in the hub to identify it as the right side for installa

HARLEY DAVIDSON FRONT AGITATOR WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Recommended Additional Parts The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) Kit Contents See Figure 1 and the Service Parts Tables. INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. See the service manual. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) 2. See Figure 1. Install valve stem assembly (D) on wheel. See the service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. See the service manual. 4. Install primary bearing with a Wheel Bearing Remover and Installer. See the service manual. The left side of the wheel has DOT cast in the wheel to indicate the primary side of the wheel. 5. Install wheel spacers (previously removed). 6. Install front wheel (1) and stock axle. See the service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly so they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR DEUCE WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to TIRES in Service Manual. 3. Assemble wheel installation kit components, stock brake disc and sprocket to wheel using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. The valve stem side of the wheel is the primary bearing side. NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. The valve stem side of the wheel is the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in Service Manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON CHROME REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
Kits 41017-00, 41026-00 and 41262-03 are designed for installation on 2000 and later XL, FXD and 2000-2002 Softail Model Motorcycles (except FXSTD and FLSTS). Kits 41260-03, 41261-03 and 41265-03 are designed for installation on 2003 and later Softail Model Motorcycles (except FXSTD and FLSTS). Kit Numbers 41017-00 and 41261-03 contain a16 inch chrome slotted rear wheel. Kit Numbers 41026-00 and 41260-03 contain a 16 inch chrome fatboy rear wheel. Kit Numbers 41262-03 and 41265-03 contain a 16 inch mirror chrome disc rear wheel. See Service Parts Illustration for kit contents. nstallation Do not re-use brake disc screws. New screws are provided for disc installation. Re-using original disc screws can result in torque loss and damage to rotor and/ or brake assembly. (00319a) Refer to the appropriate Service Manual for wheel removal and installation procedures. See Service Parts Illustration. This kit contains the necessary parts for wheel installation, however you will need to save the Axle, Axle Nut, Brake Disc, and the Drive Pulley with related hardware for reinstallation. NOTE The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from your dealer. See your dealer for the correct part number for your model motorcycle. NOTE Apply two drops of LOCTITE THREADLOCKER 262 (red) to each of the five sprocket mounting screws. Follow the bolt torque procedure in your service manual or, if installing an accessory hardware kit, in the I-sheet included with the hardware kit. Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel & Tire Cleaner Part Number 94658-98 applied with Harley Wheel & Spoke Brush Part Number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner Part Number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, Part Number 99701-84

HARLEY DAVIDSON FRONT DISC WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
INSTALLATION 1. Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in Service Manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. 2. See Figure 1. Install valve stem assembly (D) on wheel. Refer to TIRES in Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. The side opposite the valve stem is the primary bearing side. The front wheel should be installed so that the valve stem is on the right side of the motorcycle. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate the service parts table. Refer to FRONT WHEEL in Service Manual. 4. FLSTC and FLSTN models: Install wheel kit and right hand wheel spacer provided in kit installation. All other models: Install wheel spacers previously removed. 5. Install front wheel (1), stock axle, and stock axle nut. Refer to FRONT WHEEL in Service Manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner. 3. After cleaning and polishing, seal the finish with a good quality sealer, such as Harley Glaze Polish and Sealant

HARLEY DAVIDSON REAR TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to REAR WHEEL in Service Manual. NOTES Prior to removing or installing the wheel, the rear brake caliper must be removed. The cotter pin or spring clip for the axle nut must be replaced. They are available for purchase from a dealer. See a dealer for the correct part number for your model motorcycle. Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended. When mounting tires, liberally use tire lube on the wheel and tire. For tire removal, use plastic inserts between the rim and tire after breaking the bead to create a large enough gap for the rim clamps. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. See Figure 1. Install valve stem assembly (E) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components, stock brake disc, and sprocket to wheel using the service parts table. Refer to REAR WHEEL in Service Manual. NOTES Install the primary bearing first using service manual and WHEEL BEARING REMOVER/INSTALLER. The machined grooves in the hub face indicate the primary bearing side. 4. Install rear wheel (1), stock axle, and stock spacers to motorcycle. Refer to REAR WHEEL in service manual. MAINTENANCE AND CLEANING Chrome parts must be maintained regularly to keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley-Davidson Wheel and Tire Cleaner, applied with Harley Wheel and Spoke Brush. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner

Incoming search terms: