HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 103 (1690 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Remove maxi-fuse. Refer to MAXI-FUSE INSTALLATION in Service Manual. 2. Remove existing air cleaner assembly. Discard filter element, backplate, and air cleaner cover insert but save remaining parts. Refer to AIR CLEANER REMOVAL in Service Manual. 3. Remove existing exhaust system. Discard mufflers but save remaining parts for kit installation. Refer to EXHAUST SYSTEM REMOVAL in Service Manual. 4. Remove engine from chassis following the instructions in the Service Manual. 5. Remove induction module. Refer to appropriate FUEL INJECTION section in Service Manual. 6. See Figure 1. Remove and save screw (with pilot sleeve) to release fuel supply tube clamp. is03165 Figure 1. Fuel Supply Tube Clamp Screw 7. See Figure 2. Pull fuel supply tube (1) from fuel rail. -J03825 1 of 10 1 2 3 3 4 is03166 1. Fuel supply tube 2. Sealing washer 3. O-ring 4. Screw (with pilot sleeve) Figure 2. Fuel Supply Tube Assembly 8. Remove sealing washer (2) and O-ring (3) from fuel supply tube. Remove second O-ring (3) from fuel rail bore. Discard sealing washer and O-rings. 9. See Figure 3. Pull fuel injectors (1) with attached fuel rail from induction module. To overcome the resistance of the bottom O-ring (2) on both fuel injectors, gently rock assembly back and forth while pulling. 10. Remove spring clips (3) from fuel injectors. Pull fuel injectors from fuel rail. To overcome the resistance of the top O-ring (4) on both fuel injectors, gently rock assembly back and forth while pulling. 11. Disassemble engine top end, engine bottom end, crankcase, and crankshaft. Refer to appropriate ENGINE sections in Service Manual. 1 2 4 3 is03167 1. Fuel injector 2. O-ring, bottom 3. Clip, spring 4. O-ring, top Figure 3. Fuel Injector Assembly INSTALLATION Inspect Cam Clearance A clearance problem between the new cam lobe and crankcase housing may exist on certain older model engines. Failure to maintain proper clearance could result in severe engine damage. (00391b) 1. See Figure 4. Prior to starting assembly procedures, insert new cams from kit into inner needle bearings (1) located in the right side crankcase and check for a minimum of 0.030 in. clearance between highest lift point of cam lobes and crankcase housing (2) with feeler gauges. NOTE If inadequate clearance is detected, crankcase housing must be machined to provide 1.060 in. Radius clearance from center of each cam bearing bore. After machining, recheck for minimum of 0.030 in. clearance

Triumph Bonneville, Bonneville T100, Thruxton & Scrambler Dresser Rail / Sissy Bar / Grab Rail Kits Fitting Instructions

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Undo and remove the two screws and flanged sleeves (if fitted) from the rear of the riders seat. 2. Remove the seat. 3. Disconnect the battery, negative (black) lead first. 4. Locate the rear light unit wiring connector and disconnect it from the main wiring harness. 1. Rear light unit wiring connector NOTE Take care not to damage the painted finish of the mudguard. 5. Undo the four screws securing the rear mudguard to the frame, then remove the mudguard assembly from the motorcycle. 1. Rear mudguard fixings Warning Throughout this operation, ensure that the motorcycle is stabilised and adequately supported on a paddock stand to prevent risk of injury from the motorcycle falling. Warning A torque wrench of known accurate calibration must be used when fitting this accessory kit. Failure to tighten any of the fasteners to the correct torque specification may result in loss of motorcycle control and an accident. 1 1 3 of 4 6. Position the dresser rail to the frame and secure with six of the supplied M8 x 20 mm bolts (four at the rear and one on either side at the front). Tighten the bolts to 18 Nm. Scrambler only – Fit four M8 washers between the dresser rail and the rear mounting points. 1. Rear mounting points 2. M8 washer positions (Scrambler only) 1. Front mounting point (left-hand shown) 7. Ensure the rear light wiring grommet is correctly located in the front edge of the mudguard then, taking care not to damage its painted finish, position the rear mudguard to the frame. 8. Ensure the mudguard is correctly located to the rear of the airbox then secure with the original fixings tightening them to 9 Nm. 9. Ensure the wiring for the rear light unit is correctly routed then reconnect it to the main wiring harness connector. Sissy bar installation 1. Using the M8 x 20 mm bolts and spacers, loosely secure each sissy bar to the dresser rail. 1. Spacers 2. M8 x 20 mm bolts 2. Fit an end cap to each sissy bar. 3. Using the supplied M6 x 12 mm bolts and nuts, secure the backplate to the sissy bars. Ensure the badge on the backplate is facing towards the rear of the motorcycle then tighten the fixings to 8 Nm