HONDA GL1000 DYNA S ELECTRONIC IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-04-2011

download
open the top and side compartments. Locate the two ignition coils and ballast resistor directly in front of the air cleaner intake. On some models it is best to remove the air cleaner for access to the coil area. Unplug the wires from the ballast resistor. Connect the power resistor supplied with the kit across (parallel with] the ballast resistor, and reconnect the wires to the tabs provided. The resistor will become very hot during operation. That is normal, and not destructive to the resistor, however, care should be taken to keep cables and wires from coming in contact with it. Locate the blinker relay just behind the fuse box in the left compartment. The white/green wire going to the relay carries 12 volts from the ignition switch. Using the splice connector provided, attach the separate red wire included in the kit to the white/green wire, as shown below. Do not strip the wires. On 197B and 1979 models, the 12 volts can be obtained at the accessory terminal in the left side compartment. y^T^^TL. PUSH CLIP DOWN RED WIRE SUPPLIED WITH KIT SWITCHED 12 VOLTS Remove the points cover and battery cover. Remove the 10 mm bolt holding the spark advance assembly to the engine. Remove the screws holding the points plate to the engine. Disconnect the blue/yellow
and yellow point wires where they plug into the wire harness and remove the entire point/plate assembly. Notice that there are two other wires connected where the points plugged in. These are wires going to the condensers mounted in front of the battery. Unplug both wires and tuck them back out of the way. Do not reconnect. | > Remove the spark advance assembly from the engine. Remove the point cam from the advance assembly. Coat the advance assembly shaft with oil. Place the OYNA S rotor on the shaft and while spreading the weights, push the rotor down until it engages the weights. Ensure that the rotor rotates freely on the shaft as the advance weights move out and back. Install the advance/rotor assembly on the engine making sure the pin on the camshaft is engaged in the slot on the advance assembly. Install the washer and bolt, and tighten. Ensure that the rotor is still free to rotate.

TRIUMPH TWIN CYLINDER MOTORCYCLES WITH POINTS IN THE SIDE CASING INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 30-10-2010

download
1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the petrol tank and/or seat to gain access to the ignition coils, condensors and wiring. 3. For safety, disconnect the battery (preferably both terminals). 4. Remove timing cover. (The Atlas engine has the points housing behind the cylinder head). 5. Disconnect the two wires (usually black-white & black-yellow) and remove the contact-breaker plate. At the other end, these two wires must be disconnected from the ignition coils & condensors. The condensors are no longer required and can be removed. They should not be connected to the electronic ignition system. 6. Remove auto-advance unit. 7. Disconnect the remaining wires from the ignition coils. These come from the ignition switch supply. On the Norton Commando, remove the white-blue wire from the ballast resistor between the two ignition coils; the ballast resistor is no longer required. The colour of this ignition supply wire may be different on some machines; if so check using a test lamp or meter to find the live wire when the ignition is switched on. 8. Find a suitable place for the ignition module, preferably near to the ignition coils. Secure the ignition module to the frame using one or more large cable ties. An adhesive mounting base is provided; this can be affixed to the underside of the module and the cable tie passed through and around the module and frame. Do not completely wrap the module in foam rubber. 9. Using the black coil link wire, connect the negative (—) terminal of one ignition coil to the positive (+) terminal of the other ignition coil. See figs. 1/2 on page 7. 10. Take the black wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the negative (—) terminal on ignition coil #2. See figs. 1/2 on page 7. 11. Take the red wire from the ignition module, cut to length and fit an insulator and female spade connector to the end. Connect to the positive (+) terminal on ignition • BLACK COIL LINK WIRE • RED EARTHING WIRE • CRIMP CONNECTORS & INSULATORS • LARGE & SMALL CABLE TIES • CABLE TIE ADHESIVE MOUNTING BASE 3 coil #1. See figs. 1/2 on page 7. 12. For NEGATIVE EARTH electrics go to step 15. 13. For POSITIVE EARTH electrics (standard): Take the white wire from the ignition module, cut to length and fit an insulator and male spade connector to the end. Connect to one of the negative ignition feed wires previously removed in step 7 (white-blue wire for Norton Commando). The other wire (if fitted) is spare and should be covered with insulation to prevent shorting to the frame etc. 14. Take the red earthing wire, fit an insulator and female spade connector on one end and connect to the positive (+) terminal on ignition coil #1. Cut to length and fit a ring terminal on the other end and connect to a good earth point on the frame, ideally the battery positive (+) terminal. For the Norton Commando, the earth tag on the end of the condensor pack can be used (fit a female spade connector to the end of the red earthing wire). See fig.1 GOTO STEP 17

Incoming search terms: