YAMAHA V-Star 650 BIG AIR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 21-01-2012

download
Remove fuel tank and air filter assembly per Yamaha service manual procedures. 2. Remove the air silencer box under the tank. 3. Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. 4. Reinstall the air silencer box under the tank. 5. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave. Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – Faxwww.baronscustom.comtech@baronscustom.com Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6. Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot. See photo #2 Allow glue to set up and dry prior to mounting onto bike

Incoming search terms:

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Incoming search terms:

Incoming search terms: