HARLEY DAVIDSON TOUR-PAK SPOILER LIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Installation 1. If the motorcycle was previously equipped with a Tour-Pak Spoiler Light, disconnect the light wires from the motorcycle. 2. Remove the Tour-Pak Spoiler from the Tour-Pak and disassemble original light or chrome trim (as equipped). Save the original mounting hardware for later installation. 3. Attach light assembly to spoiler using 10-24 x 7/8 in. long screws. 4. See Figure 1. Route light wires through 3/8 in. hole in Tour-Pak lid. Attach spoiler to Tour-Pak lid using original hardware removed in step 2. 5. See Figure 1. Attach the wires to the inside of the Tour- Pak with adhesive backed clips as shown. Route wires out front left corner of Tour-Pak bottom and support wires inside Tour-Pak bottom with the remaining adhesive backed clips as needed. Wires will exit out the bottom of the Tour-Pak through the antenna cable grommet. NOTE On Chopped Tour-Paks drill a 3/8 in. hole in the front left corner of the Tour-Pak bottom. Route the spoiler light wires through this hole for connection to the main motorcycle wiring. 6. On 1994 and later models, proceed to step 7 for wire connection instructions. On 1993 and earlier models, go to step 11 for wire connection instructions. WIRING INSTRUCTIONS FOR 1994 AND LATER MODELS 7. Remove the seat and locate the accessory circuit connector. Route the light wires along the frame and secure with cable straps from kit. 8. Refer to the Deutsch connector section in a 1994 or later FLT Service Manual and assemble the spoiler wires into the socket connector half supplied with the LED assembly. The wire terminals shall be inserted in the connector half as follows: WIRE COLOR CODECONNECTOR CAVITY Blue 1 Red/yellow 2 Sealing plug 3 Black 4 9. Remove the plug from the accessory connector located under the seat (connector number [4A] in wiring diagram in Service Manual). Connect wire from spoiler. Turn on ignition switch and test the spoiler light operation with taillight and brake light. 1 WARNING Always connect the positive battery cable first. If the positive cable should contact the ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 10. Reattach battery

HARLEY DAVIDSON AUXILIARY LAMP WITH CLEAR LENS AND VERTICAL REFLECTOR OPTICS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1. Disconnect the battery cables, negative cable first. 2. See Figure 1. Remove passing lamp molding screw (1) and nut (2) from passing lamp molding (3). Remove molding and hardware. Retain for future use. 3. Disconnect the wire harness plug from back of auxiliary lamp assembly (4). 4 See Figure 2. Remove assembly (1) and nesting ring (2). Discard lamp but retain nesting ring. 5. Place the nesting ring at back of new lamp with concave side facing away from lamp. Install new harness provided in kit. Attach leads to the wires inside the lamp hous- ing. 6. Connect new wire harness to the new lamp. Locate lamp in housing and be sure to align tabs on lamp (3) with pockets in the nesting ring. 7. Install passing lamp molding over lamp. Rotate lamp molding so that screw is centered at bottom. Install nut and screw and secure until snug. 8. Repeat for the lamp on the opposite side. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 9. Connect the battery cables, positive cable first. 10. Test the auxiliary lamps for proper operation. If necessary, aim the lamps (see AUXILIARYLAMPS, ADJUSTMENT in the Service Manual), and tighten the lamp mounting nuts

HARLEY DAVIDSON BATTERY CHARGING HARNESS (THREE-PIN) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
1. Follow the instructions in your Owner’s Manual to remove the seat and any other components (side covers, etc.) necessary to provide access to the battery. 2. Refer to the applicable view in Figure 1 for your model. Break the battery negative (-) connection by removing the hardware assembly from the negative battery terminal. 3. Break the positive (+) battery connection by removing the hardware assembly from the positive battery terminal. 4. Clean the battery terminals and cable connectors using a wire brush or sandpaper to remove any oxidation. 5. Apply a light coating of Harley-Davidson electrical contact lubricant (Part Number 99861-02) to the battery terminals, cable connectors, battery charging harness ring terminals and connector located under the weather- shield cap. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Refer to the view in Figure 1 used for disassembly. Install the positive (RED) lead of the harness to the positive (+) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the positive (+) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the positive (+) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). 7. Attach the negative (BLACK) lead of the harness to the negative (-) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the negative (-) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the negative (-) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). Harness Routing Do not route the harness near any moving parts. Contact with moving parts may result in damage to harness. Refer to the following sections to determine the correct harness routing for your model. Be sure to avoid any components that may pinch or cut the harness, and avoid components that radiate heat. Take up any slack in the cable and store out of sight. Secure the harness with cable straps (H-D Part Number 10006), which can be purchased separately from any Harley Davidson Dealer. VRSC Model Harness Routing 1. See Figure 2. Route the battery harness/ connector (3) toward the front of the bike following the upper left frame tube. Cleanly tuck the in-line fuse (2) into the space in front of the battery. 2. Continue to route the harness/ gray connector to the front of the bike and behind the vent cover. Secure the harness with a cable strap and let the connector protrude past the cover for easy access. Trim any excess from the cable strap

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE XL1200S RACE IGNITION SYSTEM Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 26-12-2010

download
Disconnect battery, negative cable first. 2. See Figure 1. Remove seat and locate ignition module. 3. Remove the two nuts that hold the ignition module in place. 4. Unplug the two module connectors and remove module. 5. Plug in new module and secure module in place with nuts removed in step 3. Tighten nuts to 15-21 in-lbs (1.7-2.4 Nm). 6. Disconnect spark plug cables from coil towers, noting their positions for reinstallation on new coil. ® Kit Numbers 32737-98, 32738-98, 32739-98 Figure 1. Ignition Module i01020 1 of 2 NOTE The spark plug cables have numbers printed on them that correspond to numbers adjacent to the coil towers on the coil. 7. See Figure 2. Making note of wiring positions, disconnect primary wire plug from back of coil by gently prying up latch and pulling connector rearward. 8. Remove mounting bolt and remove existing ignition coil. 9. Install new coil with mounting bolt removed in previous step. Tighten bolt to 2-6 ft-lbs (3-8 Nm). 10. Plug in primary wire connector into back of coil. 11. Connect spark plug cables to new ignition coil. 1 WARNING Always connect the positive battery cable first. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 12. Reconnect battery cables, positive cable first. 13. Check engine timing according to procedures in applicable XLH Service Manual.

Incoming search terms: