HARLEY DAVIDSON CHROME DISPLAY STAND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and disconnect the battery negative (-) cable or remove the main fuse. NOTE Make sure that the cutout (B) of the strap (3) is oriented to the rear of the motorcycle after installation. 2. See Figure 2. Install strap (3) and weld nut (4) to the frame in the locations shown. 3. Position the center display stand over the mounting holes under the frame, oriented so that the skid plate faces for- ward. 4. Apply a small amount of Loctite 271 – Red to the two long screws (1) and secure the rear of the display stand to the frame by installing the two screw to the strap. 5. Apply a small amount of Loctite 271 – Red to the short screw (2) and secure the front of the display stand to the frame by installing the screw to the weld nut. 6. Tighten screws to 60-96 in-lbs (7-11 Nm) . 7. Refer to the service manual and connect the battery cables or install the main fuse. 1 2 is05370 1. Flange side 2. Flat side Figure 1. Chrome Display Stand Foot Orientation ADJUSTING THE DISPLAY STAND The left and right feet of the display stand are independently adjustable to vertically level the vehicle with the display stand extended. To adjust the display stand: NOTE The display stand can be adjusted with rear tire to ground contact or with rear tire off the ground. With the rear tire to ground contact adjustment, the rear wheel is on the ground but enough weight is on the display stand legs to make the motorcycle stable from side-to-side and front-to-back. Using the display stand to center the motorcycle will require effort. With the rear tire off the ground adjustment, the rear tire clears the ground so tire can be rotated for cleaning or maintenance purposes. Using the display stand to lift rear tire off the ground will require more effort. Do not center the vehicle with someone on the vehicle. To reduce effort, remove stored items from saddlebags, if equipped

Incoming search terms:

HARLEY DAVIDSON DIAMONDBACK "LE" CHROME SERIES CLUTCH CABLE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.

Incoming search terms:

HARLEY DAVIDSON COMBINATION SPEEDOMETER/ TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVING THE OLD SPEEDOMETER NOTE This Instruction Sheet covers several different Harley-Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 3. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 4. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 5. Unplug the 12-terminal connector [39B] from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 6. Remove the back clamp. All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 7. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 8. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it does not fall off during the following operations. 9. Set the console securely on the fuel tank

HARLEY DAVIDSON TOURING LOW PROFILE REAR SUSPENSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the seat. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) 2. Disconnect the battery cables, negative cable first or remove the main fuse if equipped. 3. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 4. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 5. Fasten the air pump, part number 54630-03A to the rear air suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 6. Using the pressure relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 7. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air hose fittings

HARLEY DAVIDSON ELECTRA-GLO LIGHT POD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION NOTES Clean the controller mounting area and the areas where the light pods will be mounted with soap and water before beginning the installation, and allow to dry thoroughly. Remove debris, dirt and grime from the vehicle areas to be highlighted. Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the light pods and controller box to vehicle surfaces. Light pods should not be located closer than 2.5 inches (63.5 mm) from exhaust pipes or mufflers, and must have 1.5 inches (38.1 mm) clearance from engine cylinders and heads. Do not install light pods with the light source facing directly away from the vehicle. Installation should be done in a way that allows the light to be seen indirectly by reflecting from chrome or painted surfaces of the vehicle. Prepare the Motorcycle To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to disconnect the battery cables, negative (-) cable first. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Locate and Install the Controller NOTE Do not mount the controller box in a location where vehicle suspension travel could result in contact with the ON/OFF switch or dimmer control. Damage to the controller box will occur. 2. See Figure 2. Locate the controller box (10) on a flat surface that will allow the red (+) and black (-) leads to reach the battery terminals and the rider to access the controls (with the vehicle parked) and, if necessary, the in-line fuse holder (A). a. Test-fit the controller box to the selected surface before installation. Do not remove the adhesive backing until ready to attach the controller box. b. Clean the controller box mounting area with one of the included alcohol swabs. Allow to dry thoroughly. c. Remove the liner from the adhesive backing of the controller box. Carefully position the controller box to the surface, and press firmly into place. Hold the controller box in position with steady pressure for about one minute. Connect the Battery Cables NOTE Verify that the ignition/light key switch is in the OFF position before attaching the battery cables. 3. Verify that the ignition/key switch is turned to the OFF position. Apply a light coat of Harley-Davidson electrical contact lubricant (part number 99861-02), petroleum jelly or corrosion retardant material to the battery terminals. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 4. Refer to the owner’s manual and follow the instructions given to install first the vehicle’s positive (+) battery cable then the red (+) light pod controller lead ring terminal to the positive (+) battery terminal. Tighten to owner’s manual specifications. Install first the vehicle’s negative (-) battery cable then the black (-) light pod controller lead ring terminal to the negative (-) battery terminal. Tighten to owner’s manual specifications. Arrange the Electra-Glo Light Pods NOTES Electra-Glo light pods (1) can be installed in a variety of locations. They are best installed on a flat surface to provide indirect lighting illuminating mechanical features, vehicle finish or for ground effects. Refer to the notes at the beginning of the Installation section. 5. Select the area or lines of the motorcycle to highlight, and suitable locations for each light pod. DO NOT permanently affix the light pods at this time. Lightly tape the pods in place temporarily until the desired visual effect is achieved Verify clearance from movement of rubber mounted engine or other moving parts, heat sources, or chafe points

HARLEY DAVIDSON FLHT OIL PRESSURE AND AIR TEMPERATURE GAUGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Oil Pressure Sending Unit To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. 1 2 3 4 is04574 1. Oil pressure sending unit 2. Cam position sensor 3. Crank position sensor 4. Main harness to ECM Figure 1. Electrical Bracket: 2000-2001 Fuel Injected Models (Magnetti-Marelli) 1 2 3 is04575 1. Oil pressure sending unit 2. Crankshaft position sensor 3. P&A siren kit Figure 2. Electrical Bracket (ECM Removed) 2002-2003 Fuel Injected Models (Delphi) -J01875 1 of 4 NOTE For 2002 to 2003 models: See Figure 2. Remove the two screws securing the ECM and remove the ECM to access the electrical bracket. 2. For 2004 and later models: Proceed to the Gauges section. For 2000 to 2003 models: See Figure 1, Figure 2 and Figure 3 for the applicable model and locate the sensor harness connector (2-piece mini-Deutsch® connector). 3 2 4 1 is04576 1. Ignition harness 2. Cam position sensor 3. Oil pressure sending unit 4. Crankshaft position sensor Figure 3. Ignition Module – Carbureted Models 3. Locate the oil pressure sending unit at the front right side of the crankcase and pull wire socket from terminal of the oil pressure sending unit. 4. Carefully draw the conduit and the pin side of mini-Deutsch connector forward and then up between the rear brake master cylinder reservoir and the frame downtube to area of the rear brake pedal. 5. See Figure 4. Remove the secondary locking wedge (3) from the pin side of the connector with a needle nose pliers. 1 3 2 is04577 1. Pin 2. Wire seal 3. Locking wedge Figure 4. Deutsch Connector Pin Side (2-pin connector shown) 6. Gently depress terminal latches inside pin housing and back out the pin in chamber #1 through the hole in wire seal. 7. Pull the oil sending unit wire through conduit and remove wire. Note the routing of the wire. 8. See Figure 9. Route the jumper (6) pins through the conduit from the kit in the same direction as the original wire noted in Step 7. Use cable straps to secure to the wire bundle. 9. See Figure 5. Locate pin chambers #1 and #2 on pin side of connector. Insert brown/green jumper pin into chamber #2 and feed until it clicks into place. Verify that pin will not back out of the chamber by giving a slight tug on the wire to confirm that it is locked

Incoming search terms:

HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

HARLEY DAVIDSON SISSY BAR MOUNTED AUXILIARY BRAKE AND TAIL LIGHT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
These kits fit 1999 and later XL models, 1996 and later Dyna™ and 1996 and later Softail models (except 2006 FXSTC) equipped with a Medallion Plate-Style Sissy Bar Upright. Will not fit with Backrest Pads that have mounting brackets that match the contour of the sissy bar medallion. Will not fit with sissy bar mounted storage bags INSTALLATION 1. Follow the instructions in the Service Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 1 2 is 01457 1. Adhesive mounted medallion 2. Push nut mounted medallion Figure 1. Medallions 5 2 1 3 4 is 01458 1. Screw 2. Screw (2) 3. Backrest bracket 4. Backrest pad 5. Mounting hole spacing (center to center) Figure 2. Backrest Pad and Bracket -J03063 1 of 5 Remove the Backrest Pad NOTE Medallions are attached to a medallion plate between the uprights of the sissy bar using either adhesive or push nuts. 1. See Figure 1. Remove and retain any existing medallion. Adhesive Mounted Medallion (1): Carefully pry the medallion (1) from the plate. Remove any adhesive residue from the back of the medallion and the sissy bar medallion plate. To avoid contaminating the adhesive backing, place the medallion in an area away from dirt and debris. Push Nut Mounted Medallion (2): Carefully pry the edge of the medallion until the medallion is free of the push nuts. 2. See Figure 2. Remove and retain the screw (1) that secures the backrest pad to the plate. 3. Remove and retain the two screws (2), backrest bracket (3) and backrest pad (4). Install the Light Assembly 1. See Figure 3. Clean the front of the medallion plate (2) with a 50/50 solution of isopropyl alcohol and water. 2. Peel the adhese bracket kit (Part Number 59545-04) and sandwich the light assembly between the bracket frame and the medallion plate. The bracket clamps will fit around the back of the sissyive backing from the adhesive tape located on the light assembly (1). Fit and hold the light assembly to the front of the medallion plate (2). 3. See Figure 6. For 2.55 inch (64.8 mm) center to center mounting hole backrest pads, use th bar arms.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE "HEAVY BREATHER" PERFORMANCE AIR CLEANER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) Original Equipment (OE) Air Cleaner Removal For carbureted models: Refer to the service manual and check the warm-slow idle speed adjustment before removing the OE air cleaner backplate. For EFI (fuel-injected) models: Have a Harley-Davidson dealer recalibrate the ECM prior to air cleaner installation. 2. Remove the air cleaner backplate following the instructions in the service manual. Retain the two breather screws (A) removed from the backplate (see Figure 1). The remaining parts can be discarded. 3. See Figure 1. Remove and discard induction module bracket (B). “Heavy Breather” Air Cleaner Installation NOTE When servicing the air cleaner, apply Loctite 243 (blue) to all threaded fasteners (both male and female threads). 4. Install the new O-rings (4) in the grooves around the breather screw holes on the carburetor or induction module side of the backplate (1 or 2)

HARLEY DAVIDSON HIGH PERFORMANCE CYLINDER STUD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit is designed for installation on 1986 and later XL model motorcycles. This kit is required on engines with compression ratios of 10:1 and higher. For XL 1200 engines with higher compression ratios, Screamin’ Eagle gasket kit part number 17046-98 is also recommended. Installation To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect the battery, negative cable first. 2. Remove top end heads and cylinders according to Service Manual instructions. Cylinder studs that are bent, scratched or broken must be replaced. Broken and bent studs distort clamp load, while scratches produce stress risers that may eventually lead to broken studs. Distorted clamp load causes head gasket leakage that may result in engine damage. Do not use a ratchet or breaker bar to install cylinder studs because they will bend the studs. 3. Remove existing cylinder studs according to Service Manual instructions. 4. Install new studs, Loctite end first. • Place a 0.313 inch DIAMETER BALL, HD Part Number 8860 (or from the XL clutch release mechanism) into the head bolt recess. Thread the stud into the head bolt until the stud bottoms on the ball. NOTE Pack clean shop towels into the crankcase openings to prevent the ball from falling into the flywheel compartment when removing the head bolt. • Clean the threads in the crankcase. • The studs have a Loctite patch on the crankcase end threads.Install the studs in the crankcase with the Loctite patch side down. • Use a T-handle to install the studs. Install studs until the free length is 4.84 ±.05 inches. See Service Manual for more detailed information. 5. Check all studs for proper height. 6. Reinstall the top end heads and cylinders according to the Service Manual Instructions

Incoming search terms: