Street Magic Magical Wizards LED Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Always wear appropriate safety gear including safety glasses when soldering or performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Temperature of bike must be at least 60 degrees F. for tape to properly cure. Read all directions before starting project. 2. Turn fuel supply valve to off position before starting. Be sure bike is on level surface and secure and cool. 3. Important: Disconnect negative battery cable from battery; refer to owner’s manual. Failure do to so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on bike. 4. Select hidden locations to mount LED Accent Lights to provide best coverage. 5. Remove fuse from fuse holder. 6. Clean mounting locations on both motorcycle and accent lights with 3M promoter, promoter sponge will dry up quickly, place sponge in sealed plastic bag when not in use. Do not touch 3M promoter with bare fingers. 7. Place piece of double sided tape on accent light if needed, lights come pre-taped on back surface. Trim excess off sides with razor blade. Carefully remove backing from double sided tape and place light on selected mounting location. Press firmly and hold for 10 seconds. Repeat for all lights to be mounted on bike. 8. Route wires from accent lights back to central points near battery compartment under seat. Route wires such that they not interfere with normal operation of bike. Cut off any excess wires, strip back insulation as required. 9. Select several locations to secure wires to frame. Secure wires using tie wraps provided. 10. Join all black wires from LEDs into one Cage Clamp Connector #1. Join all Red wires from LEDs into Cage Clamp Con- nector #2, Join all Blue wires from LEDs into Cage Clamp Connector #3, Join all Green wires from LEDs into Cage Clamp Connector #4. 11. Connect Orange wire from the remote control wire harness to the Red Cage Clamp Connector, connect Blue wire from remote control wire harness to Blue Cage Clamp Connector, connect Green wire from remote control wire harness to Green Cage Clamp Connector. Connect White wire from remote control wire harness to Black Cage Clamp Connector. 12. Crimp spade connector on ends of remaining Red and Black wires from Remote Wiring Harness. Heat spade connector with heat gun so that it shrinks around wire. 13. Connect Red Wire to Positive (+) side of battery, and Black Wire to (-) Side of battery. Take necessary precautions when making connection and refer to bike’s owner’s manual. DO NOT allow any tools to touch both positive (+) side of battery and any metal surface on bike as it will cause a short which could result in serious injury and damage to the battery or other electrical circuits.

MODEL 8100 HID/ HALOGEN MOTORCYCLE HEADLIGHT INSTALLATION

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1) Remove seat. 2) Refer to service manual to locate the following wires: An ignition signal that has power while the ignition is in the “ON” position. Terminal 30 on start relay . A “CRANK” signal (start signal) that has power while the starter motor is being activated. Terminal 86 on start relay . 3) Locate a mounting position for the module that will fit in front of or next to the battery. DO NOT MOUNT the module until all connections to the module have been made. 4) Verify the operation of the ignition and crank signals using the voltmeter or test light. Disconnect battery and make the following connections: • Connect the Blue wire from the lamp module to the ignition feed wire Terminal 30 on start relay . • Connect the Grey wire from the lamp module to the starter crank feed Terminal 86 on start relay . • Connect the Red wire from the module to one end of the fuse harness provided in the kit. • Crimp a ring terminal to the other end of the fuse harness (for connection the POSITIVE battery terminal) . • Crimp a ring terminal to the Black wire from the module. This will need to be routed to the NEGATIVE terminal of the battery • Do not in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided. 5) Securely mount ballast in chosen location. Plug the 2 wire sealed connector (RED AND BLACK 16 AWG WIRES) to the ballast. Route the Red and Black wires along the frame, and follow the harness under the fuel tank (recommended) to the battery compartment. Connect the Orange wire from the lamp module to the red wire from the ballast using connector. Crimp ring terminal to black wire coming from the ballast, and connect to the NEGATIVE battery terminal. • IT IS NOT RECOMMENDED THAT THE BALLAST BE MOUNTED IN CLOSE PROXIMITY TO ECU OR FUEL INJECTION WIRING. • Do not mount near sources of high heat (i.e. Cylinder head or exhaust manifold) . • Do not mount in a location where there is a possibility of mechanical interference from moving parts (i.e. Steering components or linkage) . • There is a 3-foot length of cable provided for connection between the BALLAST and the HID LAMP. This cable MUST NOT be modified in any way (lengthened or shortened) . Ensure that the ballast is close enough to the lamp to use the length of cable provided

BMW K1300S Rider's Manual

0

Filed Under (BMW) by admin on 27-11-2010

download
General view, right side 1 Engine oil level indicator (101) 2 Fuel filler opening (79) 3 Battery compartment (127) 4 Brake-fluid reservoir, front (102) 5 Vehicle identification number (ontheupperfront wheel control) 6 Type plate (on rear cross tube) 7 Brake-fluid reservoir, rear (105) 2 13 z Overviews Left handlebar fitting 1 High-beam headlight and headlight flasher (55) 2 Operating odometer (49) with onboardcomput- erOE Operating onboard computer (51) 3 Hazard warning flashers (56) 4 Operating turn indicators (56) 5 Horn 6 with Electronic Suspen- ionAdjustment (ESA II)OE Operating ESA (64) 7 ABS operation (58) with automatic Stability ControlOE Operating the ASC (59) 2 14 z Overviews Handlebar fitting, right 1 with heated handlebar gripsOE Heated handgrips (60) 2 Starter button (72) 3 Emergency ON/OFF switch (57) 2 15 z Overviews Underneath seat 1 Luggage loops 2 Rider’sManual (US Model) 3 Tire inflation pressure table 4 Payload table 5 Helmet holder (68) 6 Toolkit (100) 7 Engine oil fill location (102)