YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

HONDA CT 70 Owner's Manual

0

Filed Under (Honda) by admin on 23-04-2011

download
INSTRUMENT AND INIHCATOH LAMP Speedometer I) is located on the headlight case and odometer 2′. incorporated in the speedometer indicates total distance travelled. Gear speed range indicators l’_§t‘- are Curved bare shown on the Epeeciometer dial plate to indicate the recommended operating range of the respective gears. High beam indicator lamp tredi i is located at the right side of the speedometer. This lamp will he on when headlight is on high beam. mph
‘.1_ Speedometer -fgi Odometer -Ffij Gear speed r.|nge indicators L @ High boom indicator lamp I “5′ Page 13 I  ELECTRICAL CONTRUIB I lGilTIUi’~l SWIICH The ignition switch is located on the left side of the main pipe. Functions of the respective 5″.’t'lt’C|’t positions are shuvvn in the chart helovv. t lgtttttttn sti, |tch Kev position I unction ii] OFF Slfitigiertzttrical circuit I5 opened, engine ‘t.’t.’||| not I3. Electrical circttit is closed, engine can be started {for day time operattioni 4 Eiectrical circuit is closed, engine can be “-3 started {for night time operation? Key removal Key can be
removecl Kev can not be removed Kev can not he removed age 14 10 0 HEADLILIHT BEAM CDH’TROL SWITCH The headlight beam control switch {D is located on the left handle grip. “L” is low beam position llow beam light and tail light on]. “H” is high beam light and tail light on. The headlight will only operate when the ignition switch is in the on posi- tion. Reler to ignition switch page 9.eat “$2, i 1| ma‘ ‘ aw Lg; Headlight beam contxul switclr -”‘ @ “I.” position {ii “ll” position , ._ _. i HORN BUTTON This is a push button switch Q) to-zated on the right handte grip. When the horn button switch is depressed the horn wlll operate

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

1995 HONDA VFR Owners Manual

0

Filed Under (Honda) by admin on 01-12-2010

download
INSTRUMENTS AND INDICATORS The indicators are contained in the instrument panel. Their functions are described in the tables on the following pages. USA model: Odometer and tripmeter read in miles. Canadian model: Odometer and tripmeter read in kilometers. (1) Speedometer (2) Odometer (3) Left turn signal indicator (4) Side stand indicator (5) High beam indicator (6) Digital clock (7) Tachometer (8) Tachometer red zone (9) Neutral indicator (10) Right turn signal indicator (11) Fuel indicator (12) Fuel gauge (13) Coolant temperature gauge (14) Low oil pressure indicator (15) Tripmeter (16) Tripmeter reset knob 15 (Ref.No.) Description Function ————————————————- ———————————————————– (1) Speedometer Shows riding speed. (2) Odometer Shows accumulated mileage. (3) Left turn signal indicator (Amber) Flashes when the left turn signal operates. (4) Side stand indicator Lights when the side stand is put down. Before parking, check that the side stand is fully down; the light only indicates the side stand ignition cut-off system (page 54) is activated. (5) High beam indicator (Blue) Lights when the headlight is on high beam. (6) Digital clock Shows the time (page 19). (7) Tachometer Shows engine RPM. (8) Tachometer red zone Shows excessive engine rpm range in which operation may damage the engine. (9) Neutral indicator (Green) Lights when the transmissions in neutral. (10) Right turn signal indicator

Hammerhead La Vita 150cc OWNERS MANUAL

0

Filed Under (Hammerhead) by admin on 27-11-2010

download
1. Left and Right rear Mirror 2. Left and Right Brake 3. Front storage compartment (option) 4. Speedometer/ Digital Gauge 5. Main Switch 6. Battery 7. Air Cleaner 8. Seat Lock 9. Rear Light Assembly 10. Left and Right Rear turn Lights 11. Fuel Tank 12. Center Stand 13. Kick Start 14. Side Stand 15. Muffler 16. Left and Right Turn Lights 17. Head Lights 18. Rear Reflector Instrument Panel Speedometer Riding speed is indicated by KM/H and MPH. Odometer The total riding distance is in KM and Miles. The black figures in black background indicate total miles traveled. Indicating lamp or turning light It flashes when turning light is in use. Fuel Gauge Fuel Gauge indicates the remaining fuel in the fuel tank (the gauge does not work when main switch is in the “OFF” position). The gauge moves from “F”(full) to “E” (empty) as fuel decreases in the fuel tank. Fill the tank with 90 Octane or higher gasoline when the needle is approaching the “E” position. There is no reserve tank. Indicating Lamp of High beam It indicates high beam is in use. Note: apply low beam to avoid obstructing the view of oncoming drivers and drivers ahead. 1. Speedometer 2. Odometer 3. Left turn signal indicator 4. Right turn signal indicator 5. High beam indicator 6. Fault signal indicator 7. Battery Gauge 8. Fuel Gauge Instrument Control Main Switch NOTE: – Do not leave the main switch in “ON” position for an extended period of time when the engine is stopped. The battery may drain itself empty. – Lock the steering and remove the key after park to avoid theft. “ON” Position: Electric Circuits are switched on. The engine can now be started. The key can not be removed in this position. “OFF” Position: All electrical circuits are switched off. The engine stops. The key can be removed in this position. “LOCK” Position: The steering is locked when in this position. The key can be removed. Steering Lock Turn the handle bar fully to the left to lock the steering to prevent theft. Push the key in when it is in “OFF” position and while pushing the key in, turn the switch to “LOCK” position to lock the steering. Pull the key out once you are done

HONDA VFR750F SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Honda) by admin on 23-11-2010

download
Speedometer Shows riding speed. (2) Odometer Shows accumulated mileage. (3) Left turn signal indicator (Amber) Flashes when the left turn signal operates. (4) Side stand indicator Lights when the side stand is put down. Before parking, check that the side stand is fully down; the light only indicates the side stand ignition cut-off system (page 54) is activated. (5) High beam indicator (Blue) Lights when the headlight is on high beam. (6) Digital clock Shows the time (page 19). (7) Tachometer Shows engine RPM. (8) Tachometer red zone Shows excessive engine rpm range in which operation may damage the engine. (9) Neutral indicator (Green) Lights when the transmissions in neutral. (10) Right turn signal indicator Flashes when the right turn signal operates. (amber)
16 (Ref.No.) Description Function ————————————————————– ———————————————————– (11) Fuel indicator (Red) When this indicator comes on while riding, fuel reserved in the tank is about: 3.3 L (0.87 US gal, 0.73 Imp gal) Should also light for a few seconds and then go off when the ignition switch is turned ON. If it comes on any other time, refill the fuel tank as soon as possible (page 30). (12) Fuel gauge Shows approximate fuel supply available (page 18). (13) Coolant temperature gauge Shows coolant temperature(page 17). (14) Low oil pressure indicator (Red) Lights when the engine oil pressure is below the normal operating range. Should light when ignition switch is ON and engine is not running. Should go out when the engine starts, except for occasional flickering at or near idling speed when engine is warm. (15) Tripmeter Shows mileage per trip. (16) Tripmeter reset knob Resets tripmeter to zero (0) by turning the knob in direction shown