1980-2003 HARLEY DAVIDSON BARON TACHOMETER installation manual

0

Filed Under (Harley Davidson) by admin on 12-03-2012

download
1. Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off-center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating the tach internals, re-installing the bezel and retightening the set screw. 2. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, and then tighten the tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. 3. Route tach’s wire harness lead under dash for simplest and cleanest installation. 4. Make your wire connections as follows: a. Locate the pink wire under the speedo (sometimes has a plastic bullet end on it). Cut the plastic off and splice the pink wire with the green wire from the tachometer. b. Find the orange wire and attach the tach power wires to it (usually blue & red from tach (incandescent) or red & yellow for single color LED tachs. On 7-color LED models it is red from tach and red from LED controller box) . c. Locate a suitable ground (usually a bare frame bolt) and attach the black wires from the tachometer and the LED controller box (if equipped).

Incoming search terms:

HARLEY DAVIDSON CHROME 1.00 INCH (25.4 MM) DIAMETER HANDLEBAR KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
INSTALLATION Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. 2. For FLTR models only: Refer to UPPER FAIRING AND WINDSHIELD: FLTR: OUTER FAIRING: REMOVAL in the Service Manual, and follow the instructions to remove the outer fairing. See INSTRUMENT NACELLE: FLTR: REMOVAL in the Service Manual, and remove the instrument nacelle and bezel. For ALL models: Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a)

HARLEY DAVIDSON INNER FAIRING TRIM PACKAGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Install Small Instrument Bezel Covers 1. See Figure 1. Cut tape (1) into six equal pieces. 2. Remove paper liner from one side of tape and apply three pieces tape (spaced equally) to the instrument bezel (2). Press firmly. 3. Remove the adhesive backing from the back of the double- sided tape. 4. Position instrument bezel cover (3) over gauge and press firmly into place. 5. Repeat for remaining gauges. Install Large Instrument Bezel Covers 1. See Figure 1. Cut tape (4) into sixteen equal pieces. Use eight pieces for each bezel cover. 2. Repeat Steps 2 through 5 under “Install Small Instrument Bezel Covers”. 4 5 2 1 6 3 is05418 1. Adhesive tape, double-sided (2) (cut into three pieces) 2. Instrument bezel 3. Chrome bezel cover, small (4) 4. Adhesive tape, double-sided (2) (cut into eight pieces) 5. Instrument bezel 6. Chrome bezel cover, large (2) Figure 1. Install Instrument Bezels Install Front Speaker Trim 1. Gently brush or vacuum each speaker grille to remove any dust or dirt particles. 2. Cut eight 1-inch strips of narrow masking tape. 3. Without removing the adhesive backing, position the trim rings against the speaker grille

Incoming search terms: