Kawasaki ZX-9R Ninja TiForce exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 07-05-2012

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN.

Billet Aluminum Highway Board Installation Manual

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
These Highway floorboards are designed for use with Rivco highway mount clamp and arm sets. Other brands may require additional hardware. Notice that there is a left and right, when installed the heel should be in closer and the toe angled outward. 2. Place a split lock washer and then the larger washer supplied onto each of the bolts. Install the bolt thru the hole of the highway mounting arm from the backside and the threaded end of the bolt pointing towards the outside. Place one of the serrated lock washers onto each of the bolts, then the higway floorboard followed by the remaining thin washers and acorn nuts. Position the highway floorboards to the desired angle and tighten the mounting bolts and nuts securely. 3. Fold the highway floorboards up and notice the small Allen screw just above the acorn nut. This Allen screw can be adjusted out as desired to tip or angle the boards back toward the rider for added comfort. These screws are held in place with a thread locking compound, when adjusting work the screw in and out slowly to loosen the thread locker until the screw rotates as desired.

Kawasaki 2000- ZX-12R Ninja exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the lower fairing. Remove the lower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1, 2, 3, and 4 by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. Place a billet aluminum Mouthpiece ring Z on each TiForce head pipe. (see figure 3 for details) . 6. Attach the assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the head pipes fit flush and snug in the ports and Mouthpiece ring Z before tightening. 7. Install the S-Bend to the front section of the head pipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes and Mouthpiece ring Z are centered in each port. 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. (See figure 1) . 11. Place the bands approximately 118 mm from the edge of the end can. (See figure 2) . 12. Using the stock provided mounting point on the passenger foot peg, and using the stock-mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance