HARLEY DAVIDSON BATTERY CHARGING HARNESS (THREE-PIN) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
1. Follow the instructions in your Owner’s Manual to remove the seat and any other components (side covers, etc.) necessary to provide access to the battery. 2. Refer to the applicable view in Figure 1 for your model. Break the battery negative (-) connection by removing the hardware assembly from the negative battery terminal. 3. Break the positive (+) battery connection by removing the hardware assembly from the positive battery terminal. 4. Clean the battery terminals and cable connectors using a wire brush or sandpaper to remove any oxidation. 5. Apply a light coating of Harley-Davidson electrical contact lubricant (Part Number 99861-02) to the battery terminals, cable connectors, battery charging harness ring terminals and connector located under the weather- shield cap. Connect positive (+) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00068a) 6. Refer to the view in Figure 1 used for disassembly. Install the positive (RED) lead of the harness to the positive (+) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the positive (+) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the positive (+) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). 7. Attach the negative (BLACK) lead of the harness to the negative (-) battery post following the sequence shown. • On 1999 and earlier models (with original equipment), torque the negative (-) terminal post bolt to 40 in-lbs (4.5 Nm). • On 2000 and later models (with original equipment), torque the negative (-) terminal post bolt to 60-96 in-lbs (6.8-10.9 Nm). Harness Routing Do not route the harness near any moving parts. Contact with moving parts may result in damage to harness. Refer to the following sections to determine the correct harness routing for your model. Be sure to avoid any components that may pinch or cut the harness, and avoid components that radiate heat. Take up any slack in the cable and store out of sight. Secure the harness with cable straps (H-D Part Number 10006), which can be purchased separately from any Harley Davidson Dealer. VRSC Model Harness Routing 1. See Figure 2. Route the battery harness/ connector (3) toward the front of the bike following the upper left frame tube. Cleanly tuck the in-line fuse (2) into the space in front of the battery. 2. Continue to route the harness/ gray connector to the front of the bike and behind the vent cover. Secure the harness with a cable strap and let the connector protrude past the cover for easy access. Trim any excess from the cable strap

Incoming search terms:

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Victory Vegas Rear LED Turn Signal Assembly Installation Manual

0

Filed Under (Victory) by admin on 31-10-2010

download
Step 1 •Prior to installation it is recommended that you perform a Pre-Function check. To do so, remove the left side battery cover from the bike and expose the post terminals. Hold the positive red lead from the turn signal to the positive red lead of the battery and then place the negative black lead from the turn signal to the negative black lead of the battery. Do one side at a time and ensure that both sides light prior to installation. Step 2 •Remove seat (passenger too if installed) •Remove fender “eyelashes” (required first if passenger seat is installed) •Remove the fender mounting bolts •Disconnect the rear turn signal and taillight harness connector located in the battery box compartment •Remove the fender by gentle prying outward and upward on one side to clear the mounting points, then the other side •Set aside on a flat and smooth surface to protect the fender’s finish (you may want to wrap it in a large towel) Step 3 •Turn the rear fender assembly upside down on a stable and covered/protected surface to prevent damaging the fender/paint •Remove the rear tail assembly and disconnect the wiring harness and license plate light. THIS PART IS NO LONGER NEEDED! Victory Vegas Rear LED Turn Signal Assembly Installation Guide •Remove the stock metal spacers shown below and replace them with the ¼” rubber spacers included in your accessory/installation kit. Step 4 •Place the turn signal assembly mounting arms over the rubber spacers. Align the turn signal in place so the space between the fender and the turn signal tube is consistent. After completing this step, place a small amount of Loc-Tite to the bolt and slowly tighten the stock nuts snugly in place, (extreme over-tightening may damage turn signal or fender lip). You should not need to loosen the mounting arms which are attached to the turn signal bracket to obtain the ideal fit; they are pre-assembled to be aligned. Please also note that due to manufacturing tolerances in the production of the fender, the rolled inner lip of it may interfere with the turn signal assembly seating properly. If this is the case, the lip can be tapped down flush with a rubber mallet or other appropriate tool. Take the necessary precautions to maintain your fender’s finish should this step be necessary. Step 5 •Run the wiring of the turn signal assembly in an appropriate/desireable path to the stock wiring harness. See picture below as an example. Once the wires are run, cut any excess wire and install the bullet connectors (included in the installation/accessory package) to the end of the wires. Due to the small gauge of the wire it’s suggested that you double it over before placing it into the bullet connector and solder it in place. Wire as follows:

Incoming search terms:

Incoming search terms: