BMW F 650 CS Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Connection 11 Engine Freewheel housing and freewheel Nm 35 (clean thread + Loctite648) Engine block Nm 10 Double drive gear on crankshaft Nm 180 (clean thread + Loctite243) Driver to countershaft Nm 140 (clean thread + Loctite243) Pressure plate Nm 10 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Chainwheel to main shaft Nm 140 (clean thread + Loctite243) Signal transmitter Nm 8 Ignition cover Nm 10 Cylinder base Nm 10 Fastener for chain tensioner Nm 40 Oil circuit Oil filter cover Nm 10 Oil pressure switch Nm 12 (clean thread + Loctite243) Strainer cover to housing half Nm 8 Drain plug, on-frame oil tank Nm 21 Engine oil drain plug Nm 40 Oil supply/oil return lines to engine Nm 42 Oil pump cover Nm 6 (clean thread + Loctite243) Oil pressure valve Nm 24 Oil retaining valve Nm 24 Cylinder head Collar nuts for cylinder head Nm 60 Collar screws for cylinder head Nm 33 Machine screws (chaincase) Nm 10 Camshaft bearing cap Nm 10 Chain sprockets to camshafts Nm 60 threads oiled Chain guide to camshaft bearing cap Nm 10 (clean thread + Loctite243)
00.4 Cylinder head cover Nm 10 Machine screw (hole for locating screw) Nm 25 Model F 650 CS Connection 12 Engine electrics Spark plug Nm 20 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Signal transmitter Nm 8 Engine block cover, left/right Nm 10 Starter to clutch cover Nm 10 Positive lead to starter motor Nm 9 Positive contact to starter motor Nm 4 Necked-down bolt, starter housing Nm 6 Cable cover to engine block Nm 9 Cable holder to ignition cover Nm 8 Stator to ignition cover Nm 10 (clean thread + Loctite243) Ignition coil bracket to cylinder head cover Nm 9

Incoming search terms:

BMW F 650 CS Rear belt wheel cracks Removal And Installation Manual

0

Filed Under (BMW) by admin on 12-11-2010

download
Relieve the tension of the toothed belt and lift the belt off the belt wheel (refer to F 650CS Repair Manual, 00.57). 2) Remove 6 screws (see arrow in photo at right). 3) Remove the rear belt wheel. 4) Clean and degrease the tapered bores and the threads of the mounting screws 5) Carefully place the new belt wheel in position on the damper, coat the screw threads with Loctite 243 and hand tighten the securing screws. 6) Tighten the securing screws to the specified torque maintaining a diagonally opposite tightening sequence throughout (Torque to 28 NM, curing time 12 hours). 7) Measure the vertical runout of the belt wheel (refer to F 650 CS Repair Manual, 33.15). 8) Install and adjust the rear drive belt (refer to F 650 CS Repair Manual 00.57 – 00.58) 2.1 Removal of the front belt wheel Remove the front belt wheel in accordance with the instructions detailed in the F 650 CS Repair Manual. Remove the securing screw of the activated charcoal filter and let the filter canister hang by one side by the hoses, or remove it and lay it aside. Clean the splines and threads of the main shaft in order to remove all traces of Loctite. If necessary, remove corrosion from the main shaft spline (use only a brass bristle brush). 2.2 Visual inspection Check the splines of the main shaft for damage. Replace the main shaft if the splines are damaged (broken, chipped, bent or damaged teeth). Refer to the F 650 CS Repair Manual for this procedure.

Incoming search terms:

Incoming search terms: