HARLEY DAVIDSON CHROME 1.00 INCH (25.4 MM) DIAMETER HANDLEBAR KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the outer fairing. See the service manual. 3. Remove the fairing cap. See the service manual. 4. FLHX Models: Handlebar-mounted mirrors (purchased separately) are required for proper installation of this handlebar. Removal of the inner fairing may be required, refer to the service manual. If fairing-mounted mirrors are being removed: Install the two small black plugs and large black plugs (purchased separately) to plug the fairing mirror holes. Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTE Immediately wipe up any brake fluid spillage with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spillage or splashes of DOT 4 brake fluid. 5. Drain the brake fluid from the front brake reservoir and lines per the instructions in the service manual. NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. 6. Models with Radio: Remove the radio. See the service manual. Models without Radio: Remove the storage box. See the service manual. a. The four socket head screws fastening the radio or storage box to the left and right radio support brackets can be accessed through the oblong holes in the fairing brackets. Use a long shank ball-end socket to remove the screws. b. Pull the radio or storage box forward to remove it from the opening in the inner fairing. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 7. Remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 8. Note the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See the service manual. 9. Remove the front brake line assembly. NOTES Refer to the parts catalog for this year and model for a replacement OE brake line assembly and clutch cable, if needed. Ask a Harley-Davidson dealer about the selection of Genuine Motor Accessory Custom Braided Clutch Cables and Brake Lines that are available. 10. Remove the front brake master cylinder and clutch lever assemblies from the handlebar. 11. Disconnect the clutch cable from the clutch lever. See the service manual.

Incoming search terms:

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

Incoming search terms:

Incoming search terms: