Harley Davidson KNIGHT PROWLER BELT DRIVE Installation Procedures

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
STEP 1: Place bike on suitable stand where rear wheel can be rotated in 4th or 5th gear when necessary. STEP 2: Remove front exhaust pipe. If necessary, remove as a one-piece unit. * Tip – Removing front floorboard will help a lot. STEP 3: Using easiest method – bolt cutter, etc. -remove pushrods and discard. We recommend using the S&S Quickee install pushrods and S&S roller tappets WITHOUT travel limiters. Remove tappet covers and tappets. STEP 4: Remove outer cam cover and rotate engine until timing marks are aligned together. STEP 5: Using Harley-Davidson service manual procedure, retract the outer chain tension shoe. STEP 6: Remove crankshaft and crankshaft sprocket retaining bolts using Harley-Davidson service manual procedure and tools. Continue to the next page for special instructions concerning this step with 06-DYNA & CHAIN DRIVE MODELS and also with 1999 THRU 2006 CHAIN DRIVE MODELS

HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

Harley Davidson HIGH PERFORMANCE QUICK- INSTALL ADJUSTABLE PUSHRODS INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Remove stock pushrods using a bolt cutter. 2. Place the motorcycle on a hydraulic center stand with the rear wheel raised off the ground. Remove spark plugs. CAUTION 1 WARNING 1 WARNING CAUTION 1 WARNING CAUTION ® i02097.tif Figure 1. Adjustable Push Rod Kit Number 17997-99A Pushrod Tube Adjusting Screw Flats Adjusting Screw Locknut 1 of 2 Exhaust Pushrod Tube has Thicker “Finished” area and is slightly longer Intake Pushrod Tube has Thinner “Finished” area and is slightly shorter 3. With transmission in gear use rear wheel to turn engine over until both front cylinder tappets are at their lowest point. 4. Replace O-rings, lower pushrod cover and spring cover keeper with new components supplied in kit. 5. See Figure 1. Loosen locknut on all of the pushrods and adjust them to their shortest length. NOTE See Figure 1. In Step 6, pushrods with the Thinner “Finished” area on the tubes must be installed to the Intake location on the cylinders; pushrods with the Thicker “Finished” area on the tubes are slightly longer and must be installed to the Exhaust locations on the cylinders. 6. Install pushrods with pushrod covers. Be sure adjuster end of pushrod is down and ball end of adjuster is in tappet socket. 7. If hydraulic tappets are used, adjust pushrods following procedure A. With solid tappets, follow procedure B. NOTE Pushrod adjustment must be made with engine cold. PROCEDUREA (Hydraulic Tappets) 1A. Adjust pushrod length to zero clearance. 2A. See Figure 1. With the pushrod tube kept from rotating with a 1/2 inch or adjustable wrench, slowly turn the adjusting screw with a 5/16 in. wrench, 2-1/2 complete turns counter clockwise (lengthening the pushrod) as viewed from the bottom. (You may wish to mark adjuster to aid in counting turns.) 3A. Hold adjusting screw and tighten locknut with 1/2 in. open end wrench against the pushrod tube. If pushrod turns with locknut use three open end wrenches, one to hold the pushrod tube, one to hold adjusting screw and one to turn locknut.

Incoming search terms: