TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

TRIUMPH ROCKET III DRIVER FLOOR BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Starting on the left (shifter) side remove shifter pivot bolt (large allen head). Rotate the shifter assembly out of the way. Remove the retaining clip from the bottom of the foot peg pivot pin. Remove the pin and the foot peg. 2. Install the left floorboard in the original foot peg mounting location. (Note the L & R markings on the backside of the mounting blocks.) Place the allen bolt (supplied) through the original mount and the floorboard. It may also help to use the shank of a Phillips screwdriver in the bolthole at the same time to help align the holes. In some cases due to variances in the stock foot peg bracket it you may need to use a 25/64″ (.390) drill bit and drill thru both the bracket and the floorboards mounting block to allow the bolt to go thru. The blocks and their holes are machined to exact tolerances and is kept as close as possible to the size of the peg bracket so that there will not be any looseness or drooping of the floorboards when installed. Thread one of the Ny-loc nuts (supplied) onto the bolt and tighten securely. Reinstall shifter assembly and tighten securely. 3. Repeat for right side and re-check hardware for tightness. (The brake assembly will not need to be removed.)

1999 – up Ducati ST4 Forza Slip -on Installation Instructions

0

Filed Under (Ducati) by admin on 26-10-2010

download
1. Using a Vise-Grip pliers or hook, Start by removing the spring that holds the lower header together. 2. Next remove the 5mm bolt that holds the pipe on the passenger foot peg. Note You will have to use the lowest bolthole if your bike has the baggage, not the one on the passenger foot peg. 3. Remove the pipe by pulling away from bike. Fast By Ferracci Inc 1901 Davisvill Rd Willow Grove PA 19090 Tel (215) 657 1276 Version #1 07/17/01 4. Install supplied bracket loosely with 8mm bolts as shown in figure 5. Install new pipe in reverse order. First, Place header in to the lower manifold. Next, insert passenger foot peg bolt and tighten. Next tighten the two bolts on the lower part of bracket. Next apply supplied Forza sticker as shown in figure. 6. Repeat steps 2 thru 5 for the other side pipe. Once step 5 has been completed for opposite side. Reinstall spring by attaching both hooks to the new headers.

Incoming search terms: