2004 Kawasaki ZX10R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the main seat and the passenger seat 2. Remove the tail cover by removing the two bolts. 3 Place the Power Commander in the tail section and route the wiring harness on the inside of the tail section towards the front of the bike (Fig. A). 4. Remove the fuel tank. 5. Remove the air box lid by removing the 8 screws around the outer edge (Fig. B). 6. Remove the bolts shown in Fig. C. This will allow you to remove the air box. Fig. A Fig. B Fig. C i212-411 2004-2005 Kawasaki ZX10R – PCIII USB – 2 i212-411 www.powercommander.com Remove these bolts Remove screws Remove bolts 7. Locate the Throttle Position Sensor connector. This connector is located above the left hand side of the engine. This is a white 3 pin connector. Unplug this connector (Fig. D). 8. Plug the white connectors from the PCIII in-line of the stock TPS connector (Fig. E). 9. Locate the fuel rail connector behind the injector bodies (Fig. F). This connector is brown in color

Incoming search terms:

Kawasaki ZX-14 TITANIUM SIDEWINDER EXHAUST Installation Instructions

0

Filed Under (Kawasaki) by admin on 30-04-2012

download
STEP 2: PRE-ASSEMBLE HEADERS, COLLECTOR, AND MID-PIPE TO INSURE PROPER FIT BETWEEN ALL PARTS: Brock’s Performance pre-assembles the exhaust system before it is shipped to your door. We ask you to this to insure there were no shipping damages incurred before you start disassembling your bike. A lot of our customers use WD-40 applied to the joints to ease assembly, adjustment, and/or disassembly. STEP 3: REMOVE ZX-14 RIGHT AND LEFT DASHBOARDS : The right and left dashboards are held in place by three fasteners (Figure 4) which are removed with a No. 4 hex head wrench. Note that all dashboard and fairing fasteners have thin plastic washers located between the fastener head and the plastic body work. Be careful to save the plastic washers. To avoid losing fasteners and washers it is recommended that the installer place them in a container once they are removed. STEP 4: REMOVE ZX-14 LOWER FAIRING : The lower fairing consists of separate right and left side panels, both of which should be removed. The locations of the bolts and plastic push pins holding the fairing in place are illustrated in Figure 5. Details are provided below. • The plastic push pins is located in the front of the fairing (3) , aft of the front tire, and holds the left and right panels together. Remove the plastic push pins using a thin blade screw driver to lift the rivet head. Then pull the rivet from the bodywork. This will release the right panel from the left panel. • Remove the lower fairing fasteners & washers (1 & 2) on the right fairing panel with a No. 5 hex head wrench. • Remove the upper fairing fasteners & washers (4, 5, & 6) on the right fairing panel with a No. 4 hex head wrench. • Note that the top of the fairing incorporates slots into which hooks at the bottom of the mid fairing (red bodywork) fit. These hooks are shown in Figure 8. Pull the bottom of the lower fairing panel away from the bike and then downward to clear the hooks from the slots. The right side lower fairing should now separate easily from the mid-fairing. • Repeat for the left side lower fairing

Kawasaki Mule 3010 Hood Rack Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 28-04-2012

download
1. Install the Seizmik Brush Guard. – Have a friend hold the brush guard (G) in place while you slide the 1.0″ dia. tube clamps (K) in place over the middle tube of the OEM bumper, as shown in Figure 1. Secure each one in place with one of the 3/8″ x 2.25″ bolts (N), two 3/8″ washers (Q), and one 3/8″ nylock nut (R). Repeat at the top tube of the OEM bumper using the 1.5″ dia. tube clamps (J), and 3/8″ x 1.75″ bolts (O). VEHICLE FRONT Figure 2. 2. Mounting brackets – Attach the two hood rack mounting brackets to the mounting pads of the brush guard, as shown in Figure 2. Use four of the 3/8″ x 1.0″ bolts (P), eight 3/8″ washers (Q), and four 3/8″ nylock nuts (R) per mounting pad. Snug down the fasteners but do not fully tighten them yet. 3 Figure 3. 3. Crush sleeves – Insert a crush sleeve (B) into each cantilever arm assembly (C & D), as shown in Figure 3. 4. Cantilever arms – Position the Driver side cantilever arm (C) on the mounting bracket, and insert a 3/8″ dia. pivot bolt (M), as shown in Figure 4. Add a 3/8″ washer (Q) and nylock nut (R) on the other side and snug down the assembly; leave the fasteners loose enough so the components can be repositioned for fitment. Repeat this step for the passenger side. Figure 4. 4 Figure 5. 5. Lock pins – Insert the 1/2″ lock pins (Y) into the tabs on each side of the Brush Guard, fixing the cantilever arms in place, as shown in Figure 5.

Incoming search terms:

1990 Harley Davidson ULTIMA 6 SPEED BUILDERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-04-2012

download
For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5 FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 2 FIG. 6 At this time check to make sure all gears rotate freely & that all slider gears slide with no interference. Lightly lube & install supplied quad seal onto main drive gear. See fig. 6 Install Main seal using special tool # 97-164. See fig. 7 Install original spacer onto mainshaft. NOTE: Beveled side goes in towards quad seal. See fig. 8 Install supplied transmission drain plug & supplied speedo sensor plug with gasket. Install supplied shifter forks onto appropriate slider gears. See fig. 9 Lightly lube & install supplied shift fork shafts. NOTE: Short shaft is installed from the right side with the threaded hole facing out. Long shaft is installed from the left side & should not protrude from the right side of case. See fig. 10 Install supplied shift fork shaft allen head plugs. (Use red loctite to prevent movement of plug & to aid in sealing)

Incoming search terms:

Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

Incoming search terms:

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

Harley Davidson Softails Shocks Installation download

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
Progressive Suspension shocks for your Softail are designed as a direct bolt on replacement for your stockers. Although they are very similar in appearance, they have vastly improved damping and spring rates. Our shocks do not use the remote reservoir system used on earlier model Softail models. 1. Place motorcycle securely on stand or blocks so the rear wheel is slightly off the ground. 2. Per instructions in a authorized shop manual, remove your old shocks. Note location of the mounting hardware. 3. Install the Progressive Suspension shocks using the stock mounting bolts and washers. 4. Tighten all shock mounting bolts to the proper torque specifications (see shop manual for specs) 5. Progressive Suspension shocks have adjustable pre-load to compensate for varying weights. The included wrench or a Harley Davidson pre-load adjustment wrench is necessary to adjust the pre-load setting. Replacement Progressive Suspension, Inc. wrenches are available as Part # SW-784 from most Dealers and Accessory Stores and the Harley Davidson wrench is available as part #94455-89 from any Harley Davidson Dealer. Spring preload is set by us to the lightest setting. To increase preload for heavier riders/loads/passengers, loosen locknut with the inside portion of the supplied wrench or a 1 1/ 16 ” wrench and back it off several turns. Use the supplied wrench or a Harley adjustment wrench to turn the adjustment nut counterclockwise to the desired preload setting. Then tighten the 11/ 16 ” lock nut. Both shocks must be adjusted to the same, equal setting

Incoming search terms:

HARLEY DAVIDSON DYNA SIDESHOTS BLACK INSTALLATION AND REMOVAL PROCEDURE

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove seat to gain access to rear oxygen sensor connector. Unplug sensor and feed end of wire through frame so that it is free from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Remove two bolts holding rectifi er onto front of frame (near front tire). Open plastic cover to gain access to front oxygen sensor connector. Unplug sensor from harness. Remove cable tie holding wire to frame and feed end of wire through so that it is free from motorcycle. 3. Loosen heat shield clamps on both the front and rear head pipes. 4. Remove two cylinder exhaust port fl ange nuts from each head pipe, located at the cylinder head. 5. Remove front head pipe clamp bolt. 6. Remove the bolt that attaches muffl ers to the frame mounting bar. 7. Remove the complete exhaust system and set aside. Assistance may be required. 8. Remove stock mounting bar and the studs in the transmisson cover. Save the bolts, one will be re-used. 9. Remove left bolt below the transmission cover. Position mounting bracket 405-P over mounting location to determine which bolts to remove (Figure 1). Install this bolt in the top hole left vacant by the new bracket. 10. Carefully remove the fl anges and circlips from the stock exhaust system using snapring pliers. NOTE: Replace bent or damaged circlips. Check condition of stock exhaust gaskets. Replace if worn or damaged. (Recommended replacement exhaust port gaskets, Screamin’ Eagle part number 17048-98)

Suzuki C-90 VL 1500LC Rear Lowering Kit INSTALLATION AND REMOVAL MANUAL

0

Filed Under (Suzuki) by admin on 20-02-2012

download
1. Decide how far you would like to lower your bike. Refer to the hole-index chart in these instructions to determine the proper mounting location holes for the drop you want to achieve. 2. Secure motorcycle to bike lift and raise the motorcycle so the rear wheel is unweighted. 3. For easiest access to the linkage remove the tool kit holder from the left side of the bike. 4. Loosen and remove the two self-locking nuts and flat washers from connecting arm bolts from the left side of the motorcycle. 5. Slide connecting arm bolts out (it may be necessary to push bushing back to the left side to allow bolt head to drop below frame. Reinstall in the same manner). Replace stock connecting arms with your new Baron connecting arms. The end with the single hole goes down and attaches to relay arm. The end with three holes goes up and attaches to the frame. Use the hole that lowers the rear your chosen amount. Reinstall bolts, washers and nuts. Torque the two connecting arm nuts to 35 foot-pounds (48 Nm). Remove motorcycle from lift. NOTE : We recommend that you set the shock spring preload to a higher setting, especially if the motorcycle will be used for carrying a passenger or heavy loads.

2001-2008 Suzuki V-Strom DL650 And DL1000 Adapter Installation Manual

0

Filed Under (Suzuki) by admin on 15-02-2012

download
Adapter Parts List Item Desc. Quantity A. Front Adapter 1 B. Rear Adapter 1 C. Frame Grabber, Front 2 D. Frame Grabber 1 E. 5/16 x ½” Button Head Screws 4 F. M8 x 50mm Bolts 2 G. Washers (Not shown) 6 2. Assembly Instructions Familiarize yourself with all of the parts in the Main Arm and Motorcycle Adapter assemblies. Follow these installation instructions FIRST . The following instructions include our recommended torque values for all fasteners used to assemble the Johnny Rack™. Do not exceed those torque values when installing the rack, otherwise damage to the Main Arm may occur. When stock mounting points are used to mount the rack to the motorcycle, refer to the motorcycle user’s manual for recommended torque values. 1. Remove the seat, the rubber rack cover on the rear rack or if you have a Givi Top Case mounting plate remove it too. Remove the 4 bolts shown (A and B). 2. Align front frame grabbers over front grab bar mounting holes (A). 3. Reinstall original bolts that you removed. Torque to 150in.lbs. 4. Place rear frame grabber over holes on rear rack (B). 5. If you do not have side luggage racks installed on the motorcycle, you will need to place 3 stacked washers (3/4 ” OD) over each hole and under the frame grabber to take up the extra space.

Incoming search terms: