2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

YAMAHA FJR 1300 2006 GPS-Halter INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 10-01-2012

download
Mounting Instructions SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts. Alle vom Motorrad gelösten Schrauben sind gemäß Herstellerangaben wieder

Incoming search terms:

Honda GL 1800 FOG LAMP INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-11-2011

download
Disconnect the negative cable from the battery before installing this accessory. • To prevent scalding, allow the engine and cooling system to cool before installing this accessory. • The memories of the tripmeter, clock, radio andbsuspension system will be erased when you disconnect the battery. Reset the memories after reconnecting the battery. • Tighten the screws, bolts and nuts securely. • Trim the excess ends off the wire ties after attaching them to the wire harnesses. Do not allow the cut part of the wire tie to interfere with another harness or brake pipe. Using cutting pliers, cut out the marked areas from the front lower cowl. Finish the edges of the holes smooth and flat with a file. 1. Disconnect the negative cable from the battery. 2. Remove the front lower cowl and bolts as described in the Service Manual.

HARLEY DAVIDSON VRSCF RIGID SADDLEBAGS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Kit Contents See Figure 5 and Table 1. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the rider seat and passenger pillion per the instructions in the service manual. 3. See Figure 1. Remove the four rear fender mounting bolts (1) and washers (2), and the passenger grab strap (3). If necessary, move the ECM to better access the fender mounting bolts. 1 3 2 is05463a 1. Bolt (4) 2. Washer (4) 3. Grab strap Figure 1. Fender Mounting Bolts 4. Disconnect the six-way tail lamp socket housing and four- way turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness. 5. If a luggage rack, sissy bar upright or both have been mounted on the rear fender , remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. NOTE The rack and/or upright will remain attached to the rear fender when the fender is removed. 6. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure 2. Remove the two bolts (8) holding the side license-plate bracket (1) to the seat pan (9). c. Remove the license-plate adjuster bracket (2) carriage bolt (3), washer (4) and lock nut (5), and the license- plate illuminator (6) and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (1), screws (7) and bolts (8) can be discarded. Set the remaining items aside for installation to the new side license-plate bracket. 8. Remove and discard the rear side reflectors (10). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. NOTE Access to the shock absorber adjustment collar is more difficult with the saddlebags in place. 9. Adjust the rear suspension preload, if desired, per the instructions in the service manual

SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

YAMAHA ROADLINER AND STRATOLINER PASSENGER FLOOBOARDS

0

Filed Under (Yamaha) by admin on 26-12-2010

download
1. Remove the passenger foot pegs pivot bolts and nuts. Remove the pegs, springs, detent ball and shims. 2. Locate the black mounting blocks supplied, notice they are marked “L” and “R” on their outer face. Install the blocks into the slots or clevises where you removed the foot pegs the tapered end should be facing down and the “L” and “R” to the outside. Install the original bolts and nuts removed earlier and tighten the bolts securely

2007 King 50 Specifications, Owners Parts, Service Tuning

0

Filed Under (Cobra) by admin on 03-12-2010

download
Use a fuel / oil mixture of 32:1 for the full 8 hour break-in period. Be sure to use high-octane pump gas, with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil . (Part # MCMUOL02) CAUTION: Failure to use proper fuel, oil, or fuel/oil mixture may result in premature engine wear or damage to the machine. Adhering to the following break-in schedule will result in long lasting high performance machine. • Start bike on stand • First 5 minute period, operate the bike on the stand with a combination of idle and high RPM operation. (avoid prolonged high RPM but spin the rear wheel good at least once or twice per minute) • Allow bike to cool • Ride for 15 minutes maximum (avoid prolonged high RPM operation and avoid abusing the clutch with throttle blipping. • Cool and inspect bike for loose fasteners. • Next ½ hour of operation, avoid prolonged operation at Wide Open Throttle. • After 1 hour of operation o Check for loose bolts and nuts on the bike and retighten as necessary (proper toque values are listed under Specifications). o Clean the carburetor bowl. o Change the transmission / clutch lubricant. • After 8 hours of operation o Change the fork oil. o Have a Certified Cobra Mechanic change the shock oil. • Your bike is now ready for the highest level of competition! NOTE: During break-in the bike will likely lose some engine coolant through the radiator overflow hose. Losing up to 4 oz (120 ml, ½ cup) is normal. Proper coolant level will cover the top of the radiator cores. Removing the radiator cap and looking inside is the only way to check the coolant level. 8 Never open the radiator cap of a machine that has a hot or warm engine or one that has recently been ridden. Burning and scalding could occur. CAUTION: It is important that the radiator cap is installed correctly and completely otherwise engine damage could occur. Starting Procedure Before starting the machine inspect the following: • Check for proper tire pressure in both tires. • Observe the chain tension and adjust if necessary. • Observe the coolant level and fill if necessary. • Verify that the chain rollers and sliders do not have improper wear. • Verify that the handlebars are tight. • Check the throttle for smooth operation and that it ‘clacks’ shut properly. • Check for loose bolts and nuts, and re-torque as necessary. • Verify that the air filter is clean and properly saturated with oil. • Insure that the fuel tank contains an adequate volume of fuel / oil mixture to complete the distance required. (High octane pump gas with Cobra’s specially formulated Cobra Venom 2-cycle Race Oil ) • Turn the fuel on by rotating the fuel petcock knob to the vertically downward position (reserve position is horizontally forward

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

BMW Motorcycles K-Models Maintenance Schedule

0

Filed Under (BMW) by admin on 12-11-2010

download
Check operation of sidestand switch (angle); orretracting sidestand linkage (K75′s) Apply silicone sprayto guide rods of adjustable windshield (onlyK1100LT, K75RT) Check torque at the bolts and nuts: • engine to frame • suspension strut mounts • side&centerstand pivot • rearwheel studs • front axle studs, clamp bolts, brake calipermounting bolts Final Inspection with Safety/ Operating check: • Condition of tires and wheels • Lights, horn, and signal system • Telltale and warning lights • Clutch and gearshift • Steering, hand & footbrake, ABS • Instruments (including optional accessories, radio, etc.) • Check &adjust engine idle speed • Check and adjust CO content of exhuast (models with closed loop catclyic con verters • Test ride, visual qualitycheck