HARLEY DAVIDSON PASSING LAMP/DIRECTIONAL SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION 1. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) NOTE There are two possible methods of connecting the directional signal wires; using the 6-place connector, or by splicing the wires using connectors supplied in the kit. If the splicing method is selected, it will not be necessary to remove the fuel tank. However, the splices will be visible. Proceed to Step 4. 3. Remove the fuel tank according to the procedure in the appropriate Service Manual. 4. See Figure 1. Remove the existing right directional signal according to the procedure in the appropriate Service Manual. Save the internal-tooth lockwasher (1) and spacer (2). 5. Place the internal-tooth lockwasher (1) and spacer (2) (saved in Step 4) on the mirror shaft, and install the mirror (3) in the mounting bracket. Secure the mirror using an internal-tooth lockwasher (4) and acorn nut (5) (both supplied in the kit). If the acorn nut (5) “bottoms” without tightening, add a spacer (6) from the kit in the location shown. 6. Repeat Steps 4 and 5 for the left directional signal.

Air Shammy Model G220/ G220X/ G220XP Owners and Operations Manual

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
NOTE: This step is now performed at Air Shammy. 1. Slip clamp over rubber adapter on blower body. 2. Slip Adapter into the rubber adapter till it bottoms out. 3. Tighten clamp to secure Adapter to blower body. Figure 2 Slip hose over blower adapter Press fit end of hose over the adapter. Fit should be very snug. Figure 3 Slip hose over nozzle. Fit should be snug. On G220XP models, this is where the extension tube can be used. Slide hose over extension tube and slide nozzle into other end of tube. Air Shammy is manufactured by Carelli, LLC. Carelli, LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from date of purchase. If a product proves to be defective in material or workmanship during the warranty period, Carelli, LLC will, at its sole option repair or replace the product. Warranty is voided if product is used for commercial purposes. Carelli, LLC’s liability is limited to the cost of repair or replacement of the product and shall not be liable for damage to other property caused by defects in the product or any other damages whether incidental, consequential or otherwise.

KTM Enduro Engineering Shock Spring Removal And Installation Instructions

0

Filed Under (KTM) by admin on 12-11-2010

download
1 Place motorcycle on a stand so that the rear wheel is off the ground. 2 Remove the upper shock bolt. (Figure 1) 3 Remove the lower shock bolt. (Figure 2) 4 Remove the shock from the motorcycle by sliding it down and out the right rear side of the bike. (Figure 3) 5 Place the shock upside down in a vice with soft jaws. Loosen the retaining ring lock screw with a 4mm Allen wrench. (Figure 4) 6 Using EE KTM shock wrench #22-300 (Figure 5), loosen the retaining collar enough to provide ¾ clearance between the bottom of the spring and the spring retaining collar. (Figure 6) 7 Push the spring retaining collar down to access the retaining clip. (Figure 7) 8 Remove the retaining clip. 9 Remove the spring retaining collar by sliding it up and off of the shock clevis. (Figure 8) 10 Slide the shock spring up and off of the shock. 11 Slide the new spring onto the shock. It should be sitting on the adjusting collar. 12 Re-install the spring retaining collar by sliding it over the clevis far enough to allow the retaining clip to be installed. 13 Install the retaining clip. Make sure that it is fully seated in the groove. 14 Slide the spring retaining collar up until it bottoms out on the retaining clip. 15 Tighten the spring adjusting collar until the bottom of the spring contacts the spring retaining collar. Turn the spring adjusting collar a couple more turns to put a small amount of pre-load on the spring. 16 Remove the shock from the vice and re-install it on the bike by reversing removal steps. Make sure to torque the upper and lower shock bolts to the manufacturer’s torque spec. 17 Set static and race sag as specified in your owner’s manual. Remember to torque the adjusting collar lock screw to manufacturer’s specification

Incoming search terms: