HARLEY DAVIDSON CHROME MASTER CYLINDER AND CLUTCH BRACKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
MASTER CYLINDER REMOVAL See Figure 1. Master cylinders designed for dual disc (two caliper) operation have an 11/16 inch (17.5 mm) bore, while those that are designed for single disc (one caliper) operation have a 9/16 inch (14.3 mm) bore. The bore size is stamped (1) on the master cylinder assembly inboard of the handlebar clamp bracket. NOTE Do not use an 9/16 inch bore master cylinder assembly on dual disc (two caliper) models or dual disc 11/16 inch bore master cylinder assembly on single disc (one caliper) models. These master cylinder assemblies are not interchangeable. Using the wrong assembly can adversely affect braking efficiency or result in brake failure which could result in death or serious injury. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1 is 01230 1. Bore stamp size location Figure 1. Verify Correct Master Cylinder Bore Size 1. Open bleeder nipple caps on front brake caliper. Install end of a length of clear plastic tubing over caliper bleeder valves, while placing free end in a suitable container. Open bleeder valves about 1/2-turn. Pump brake hand lever to drain brake fluid. Close bleeder valve. Avoid leakage. Be sure gaskets, banjo bolt(s), brake line and master cylinder bore are clean and undamaged before assembly. (00322a) 2. Remove bolt and two steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 3. See Figure 2. Place the cardboard insert between the brake lever and lever bracket

Incoming search terms:

HARLEY DAVIDSON LOWER FORK BRACKET (TRIPLE TREE) COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. For models equipped with air baffle: See Figure 1. Remove and discard the two hex screws (2) and flat washers (3) holding the baffle (1) to the fork stem and bracket assembly(4). Retain the baffle for later reassembly. For models not equipped with air baffle: Remove and discard the two plugs from the rear of the fork stem and bracket assembly (4). 2. Remove and discard the hex socket head screw (6) holding the brake line manifold (5) to the underside of the fork stem and bracket assembly. 3. Place the lower fork bracket cover into position covering the brake line manifold. Attach the cover (and the baffle, if so equipped) to the fork stem and bracket assembly with the two 1/4″ self-tapping hex screws from the kit. Tighten securely. 4. Install the 5/16″ self-tapping hex socket screw through the cover and brake line manifold into the stem and bracket assembly. Torque to 10-15 ft-lbs (13.6-20.3 Nm). 5. Verify that the throttle and clutch cables are routed properly and do not interfere with steering the vehicle. After disturbing the brake system, BEFORE moving motorcycle, you must pump brake fluid until the pistons push the pads against the brake disc. If you don’t pump fluid pressure up again, the brake will not be available to stop the motorcycle which could result in death or serious injury. After disturbing the brake system, always test motorcycle brakes at low speed. If brakes are not operating properly, or braking efficiency is poor, testing at high speeds could result in death or serious injury

HARLEY DAVIDSON ROAD KING FAT HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
PREPARATION – ALL MODELS To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will dama ge painted and bod y panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled D.O.T. 4 brake fluid. 2. See the service manual and drain the brake fluid from the front brake reservoir. ORIGINAL HANDLEBAR REMOVAL NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 1. Using a T-40 TORX® drive head, remove and retain the button head screw on the underside of the fork stem and bracket assembly that holds the brake line manifold tee. 2. Carefully make note of the front brake line routing and the orientation of the banjo fittings. Disconnect the brake line from the front brake calipers and the front brake master cylinder assembly. Save the banjo bolts, but discard the two gaskets found at each banjo fitting. See FRONT BRAKE MASTER CYLINDER in the service manual. 3. Remove the old brake lines from the motorcycle. 4. Using a T27 TORX drive head, remove the front-brake master cylinder and clutch-lever assemblies (refer to CLUTCH CABLE in the service manual) from the stock handlebar.

Incoming search terms:

2002-2007 HONDA VFR 800 WITH ABS GALFER BRAKE LINE KIT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 03-03-2011

download
Prep the motorcycle for this job A. Park motorcycle on the center stand in a well-lit shop (Fig.A) B. Note: it is not absolutely necessary to remove the fuel tank and body panels. However, brake fluid is VERY CORROSIVE TO PAINT. We decided to be safe (Fig. B) and removed the lower fairing left and right rear sides, fuel tank, front fender, seat, and black A B plastic inner fairing front parts, battery cover, and rear master cylinder cover according to the owner’s manual. This also gives better access to the fittings. (Fig C) C. After safely storing the body panels and fuel tank, remove wind shield, (brake fluid, even a drop, will permanently mark any clear plastic), cover the dash and all gauges with a towel. II. Draining the brake fluid from the systems. A. A copy of the factory instructions has been included with this kit on how to properly and safely drain, fill and bleed the brake fluid from the brake systems. Follow the directions closely and remove the fluid according to the instructions. Dispose of the old fluid properly—DO NOT REUSE. B. If you purchased the clutch line, then perform the following steps (Fig D): In the bag marked Clutch Line: remove the left side lower body panels. Remove vehicle speed sensor, and remove the coolant C D tank. Remove the clutch fluid from the master cylinder on the left clip-on. Remove the fluid from the clutch line and slave cylinder. This factory line is NOT attached along the inner frame spar so here is a little trick that made this a 20- minute job including the bleed: 1. Remove the banjo bolts from the master cylinder and the clutch slave ends. 2. With a nice heavy wire tie, attach the slave end of the new braided line to the lever end of the factory line. Snip off the tail of the wire tie. Wrap this “joint” with electrical tape. 3. Pull from the factory slave end until you get the braided line end to the clutch slave. If it gets caught on something, try turning the end you are pulling from. 4. Remove the tape, carefully cut off the wire tie, install new sealing washers and bolts at both ends and torque to 17-21 foot/lbs. maximum. Bleed the clutch. III. Removing the factory front brake hoses and calipers – Front A. With the fluid drained and disposed of properly, loosen the bolts that hold the right caliper to the right fork leg (Fig E). Also remove the two 8mm bolts from the ABS front wheel speed sensor. Loosen all of the hose mounting blocks on the front forks on both sides; also loosen the blocks for the crossover pipe (Fig F) between the fork legs. Also loosen the frame pipe mounts and the mount for the front lever line that is also E attached to the right side of the frame. Loosen the left caliper mounting bolts (Fig G). B. Remove the calipers and remove the hose mounts under the lower triple tree. Remove the hard pipes from both the left and right hard pipe to soft line frame mounts on the frame (Fig. H). On the front ABS modulator remove the short soft line that is connected to the mount block. (Fig I.a. & I.b.) C. Carefully remove the

Incoming search terms:

2003 SUZUKI SV 1000 Service Manual

0

Filed Under (Suzuki) by admin on 26-02-2011

download
HOW TO USE THIS MANUAL TO LOCATE WHAT YOU ARE LOOKING FOR : 1. The text of this manual is divided into sections . 2. The section titles are listed in the GROUP INDEX . 3 . Holding the manual as shown at the right will allow you to find the first page of the section easily . 4. The contents are listed on the first page of each section to help you find the item and page you need . COMPONENT PARTS AND WORK TO BE DONE Under the name of each system or unit, is its exploded view . Work instructions and other service information such as the tightening torque, lubricating points and locking agent points, are provided . Example: Front wheel SYMBOL Listed in the table below are the symbols indicating instructions and other information necessary for servicing. ENGINE OIL SUZUKIrecommends the use of SUZUKI PERFORMANCE 4 MOTOR OIL or an oil which is rated SF or SG under the API (American Petroleum Institute) service classification. The recommended viscosity is SAE 1 OW-40 . If an SAE 1 OW-40 oil is not available, select an altematice according to the right chart . BRAKE FLUID Specification and classification: DOT 4 A WARNING Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system, otherwise serious damage will result . Do not use any brake fluid taken from old or used or unsealed containers . Never re-use brake fluid left over from a previous servicing, which has been stored for a long period. FRONT FORK OIL Use fork oil L01 or an equivalent fork oil . GENERAL INFORMATION 1-5 ENGINE COOLANT Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only . WATER FOR MIXING Use distilled water only . Water other than distilled water can corrode and clog the aluminum radiator . ANTI-FREEZE/ENGINE COOLANT The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze . Therefore, the engine coolant should be used at all times even though the atmospheric temperature in your area does not go down to freezing point. Suzuki recommends the use of SUZUKI COOLANT anti-freeze/engine coolant. If this is not available, use an equivalent which is compatible with an aluminum radiator . LIQUID AMOUNT OF WATER/ENGINE COOLANT

Incoming search terms:

HARLEY DAVIDSON SPORTSTER BRAIDED REAR BRAKE LINE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
This kit fits 1988-2003 XL models. INSTALLATION Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Drain Brake Fluid 1. Remove bleed screw cap on rear brake caliper. 2. Install one end of a length of plastic tubing over caliper bleeder valve. Place free end of the tubing in a suitable container. 3. Open the bleeder valve about one-half turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not re-use brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. 2. See Figure 1. Remove screws from the three P-clamps and one bracket used to secure brake line to motorcycle. a. Save all screws except bracket screw and save stock P-clamp, located at the right side sprocket cover, for later use. b. Do not mix up the screws. The screws must go back into the same threaded hole in which they were removed. c. Discard remaining two P-clamps. 3. Note brake line routing, then remove existing brake line. NOTE This kit contains clamps to replace the original equipment clamps removed, except for the small clamp on the right side sprocket cover.

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Honda Goldwing GL1800 Independent Rear Suspension Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame

Honda Goldwing GL1800 Independent Rear Suspension Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm . 5.1 Explanation of OEM brake system and changes From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Trike Conversion Kit.

HARLEY DAVIDSON STREET SLAMMER HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
This kit does not fit models equipped with Hydraulic Clutch Kits, handlebar mounted gauges or the Road Tech® Radio or FLHRS models equipped with an accessory windshield. REMOVAL Preparation – All Models To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. See the service manual and remove the seat and disconnect battery cables or remove the main fuse. Save the seat hardware for installation. -J04406 When servicing the fuel system, do not smoke or allo w open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Softail and Dyna models: See the service manual and loosen the fuel tank. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) NOTES Immediately wipe up any brake fluid spills with a clean, dry, soft cloth. Follow up by thoroughly wiping affected area with a clean, damp, soft cloth (small spills) or washing with a large quantity of soapy water (large spills). Cover nearby motorcycle surfaces with a polyethylene protective sheet to help protect against damage to finish caused by spilled DOT 4 brake fluid. 3. See the service manual and drain the brake fluid from the front brake reservoir and brake lines. Handlebar Removal – Dyna and Softail NOTE Cover the front fender and the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 1. Note the front brake line routing and the orientation of the banjo fittings. See the service manual and disconnect and remove the brake line. Save the banjo bolts, but discard the brake line gaskets. 2. Remove the plastic wiring retainer clips that secure the turn signal harnesses to the handlebar, if equipped. 3. Remove the front brake master cylinder and clutch lever assemblies from the handlebar.

Incoming search terms: