2008 SUZUKI GSXR1300 Hayabusa Front Brake Line Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-01-2011

download
Step 1: Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) single banjo bolts. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines, and all other installations void warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of your machine; we took this piece off to ease installation. Remove the OEM hose holder, and keep the bolt for later use. (See picture C) Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, straight banjo labeled for right line, washer, 12-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds. Step 5: Route both brake lines through the enclosed c-clip, and attach to the lower triple clamp using the bolt from the OEM holder. (See picture B) Drop the lines down and thread the single banjo bolts at each caliper using the following sequence: single banjo hex, washer, 20-degree banjo, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions

2007-2008 KAWASAKI ZX-6RR GP Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 05-01-2011

download
Step 1: Identify the key components that complete our GP kit: You should have 3-line (front kit) , 3 SINGLE banjo bolt and 1 C-CLIP. There are also a total of 8 washers. 6 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines, all other installations will VOID the warranty . Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the GALFER GP 3-Line starting with the master cylinder line (top line). Torque level is 12 to 13 ft pounds. (See picture A2) Step 5: Install the C-CLIP provided to the lower triple tee left line needs to be held by c-clip [see picture A4] . Lower lines will travel in front of the forks to the calipers; three single banjo bolt (see picture A1) are included for master cylinder to each caliper. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo (Top line), and washer. Single banjo bolt torque level is 12 FT Pounds. ( See picture A2 for positioning) Make sure that the [ CALIPER fittings ] on each caliper are positioned [ positioning ] (see picture A5- A6) . Thread banjo bolt into the caliper, and torque bolt to 12 to 13 Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and are clear of any obstructions. Once the lines have been checked for clearance.

2005 HONDA CBR 600RR Superbike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 03-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 2 lines (front Kit), and 1 Double banjo bolt and 2 lower adapters. There are also a total of 7 washers, 5 will be used, and 2 are spares. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer adapter, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. (See picture on adapter A) Step 5: Install right and left lines to the master cylinder, the right line is the shortest out of the two lines. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. (Picture B). This is the sequence on the master cylinder: Master cylinder, washer, straight banjo (from right line), washer, 12 degree banjo (from left line) washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds . (For positioning see picture G). Banjo 12 on left line must be facing a bit more to the left than the straight banjo of right line, so that the lines can cross at lower triple clamp better. On the calipers, make sure that the 90-degree fittings are pointing out a little bit, thread banjo end to the adapter, torque the end to 6 ½ Ft pounds . (See pictures C, D, E) Before you begin bleeding process, please check for clearance of the lines, push on the front end down, see that the lines are not binding with anything and that when the front end is fully extended or fully under pressure the lines are traveling correctly and clear from any obstructions. Ones the lines have been check for clearance; the two lines are Zip tied together at the same level of the lower triple clamp area. (See pictures F), please make sure that lines cross each other. Step 6: Bleed system, conventional bleeding, pump and release the air from caliper bleed nipples… DOT 4-brake fluid is recommended.

Incoming search terms:

YAMAHA ROAD STAR LONGSHOT EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 28-12-2010

download
1. Remove the header flange nuts from the rear cylinder. 2. Loosen the muffler clamp on the front head pipe. 3. Remove the two muffler mounting bracket bolts, located between the two mufflers. 4. Carefully separate the front head pipe from the muffler assembly. Remove the muffler assembly with the rear head pipe attached and set it aside. 5. Remove the header flange nuts from the front cylinder. Remove the front head pipe and set it aside. 6. Remove the muffler mounting bracket from the frame. Note: The rear brake hose must be disconnected from the rear brake caliper in order to remove the muffler mounting bracket. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Reconnect the brake hose to the rear caliper. Important : Bleed the rear brake to remove any air from the system and refill the reservoir with the proper brake fluid. 2. Install the new mounting bracket (stamped 274) to the frame, by aligning the two 10mm holes in the bracket with the two holes in the frame below the right rear footrest (where the stock mounting bar was removed). Use the two 10mm bolts and lock nuts (supplied), do not tighten at this time. Note: The bracket will bend away from the motorcycle when mounted correctly. Refer to figure 1. 3. Connect the brake hose clip to the muffler mounting bracket, using the 6mm bolt and lock nut (supplied). Refer to figure 1. 4. Install the chrome flanges (supplied) on to both the new head pipes. 5. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 6. Install the front head pipe using the stock nuts, do not tighten at this time. 7. Install the rear head pipe using the stock nuts, do not tighten at this time. 8. Install one muffler clamp (supplied) over the front (notched end) of each muffler. 9. Slip one muffler onto the front head pipe. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the muffler and attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. 10. Repeat step #8 for the rear muffler. 11. Align the mufflers so they are parallel when viewing from the right side of the bike, and tighten the 5/16″ flange bolts on the back side of both mufflers. 12. Tighten the two 10mm bolts that mount the bracket to the frame. 13. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 14. Place the appropriate heat shield onto the rear pipe, wrap the hose clamps around the head pipe and tighten. Repeat this step with the front heat shield

Kymco People 125/ 150 FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION

0

Filed Under (Kymco) by admin on 12-12-2010

download
SERVICE INFORMATION GENERAL INSTRUCTIONS Remove the motorcycle frame covers before removing the front wheel. Jack the motorcycle front wheel off the ground and be careful to prevent the motorcycle from falling down. During servicing, keep oil or grease off the brake drum and brake linings. Contaminated brake disk or brake pads reduce stopping power. Clean the contaminated brake disk with high-performance brake degreaser and replace the brake pads. Do not use brake fluid for cleaning. Bleed air from the brake system if the brake system is removed or the brake is soft. Do not allow any foreign matters to enter the brake system when filling it with brake fluid. Brake fluid will damage painted surfaces and plastic parts. When servicing the brake system, use shop towels to cover and protect rubber, plastic parts and coated surfaces. Wipe off any spilled brake fluid with a clean shop towel. Inspect the brake system before riding. SPECIFICATIONS Item Standard (mm) Service Limit (mm) Axle shaft runout ─ 0.2 Radial ─ 2.0 Axial ─ 2.0 Front brake lining thickness 5.5 2.75 Front shock absorber spring free length 260 252 Brake disk thickness 3.2_3.5 3.0 Brake disk runout ─ 0.25 Brake master cylinder I.D. 12.700_12.74312.75 Brake master cylinder piston O.D. 12.657_12.68412.64 Brake caliper piston O.D. 33.910_33.93433.901 Brake caliper cylinder I.D.

DAZON RAIDER CLASSIC OWNER'S MANUAL

0

Filed Under (Dazon) by admin on 28-11-2010

download
Tires: Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damages or excessive wear. z Nuts & Bolts : Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight. z Underbody & Exhaust System: Check for and remove any dirt, vegetation or other debris that could be fire hazard or interfere with the proper operation of the BUGGY. z Air Cleaner Housing Drain Tube: Check for carbon deposits in the drain tube. If necessary, clean the tube and check the air cleaner housing. z Leaks, Loose Parts : Walk around your BUGGY and look for anything that appears unusual, such as a leak or loose cable. z Lights : Make sure the headlight, brake light and taillight are working properly. z Throttle : Check the free play and adjust if needed. Press the throttle to make sure it moves smoothly without sticking, and snaps back automatically when it is released. z Brakes : Press the rear brake pedal several times, check for proper brake pedal free play. Make sure there is no brake fluid leakage. z Engine Stop Button : When engine is running, press and hold the Engine Stop Button for two seconds. Make

HARLEY DAVIDSON CHROME FRONT BRAKE MASTER CYLINDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. See Figure 2. Drain the brake fluid. a. Open bleeder nipple cap on front brake caliper. b. Install end of a length of clear plastic tubing over caliper bleeder valve, while placing free end in a suitable container. c. Open bleeder valve about 1/2-turn. d. Pump brake hand lever to drain brake fluid. e. Remove cover. f. Close bleeder valve. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) 2. Remove bolt and 2 steel/rubber washers to disconnect fitting of hydraulic brake line from master cylinder. Discard washers. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 3. 5/32 in. (4 mm) Cardboard Insert 3. See Figure 3. Place the cardboard insert between the brake lever and lever bracket. 4. Using T27 TORX® drive head, remove the 2 screws with flat washers securing the handlebar clamp to the master cylinder housing. Remove the brake lever/master cylinder assembly and clamp from the handlebar. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. 6. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE New master cylinder comes with all internal components preassembled. It is not necessary to remove the components from the bore of the old master cylinder. See Figure 9. Use denatured alcohol to clean clutch system components. Do not use mineral-based solvents (such as gasoline or paint thinner), which will deteriorate rubber parts even after assembly. Deterioration of these components can cause clutch failure, which could result in death or serious injury. (00296a) 7. With denatured alcohol, clean and inspect all parts that will be reused. Replace as necessary and wipe dry with a clean lint free cloth

Incoming search terms:

Demonstrate knowledge of motorcycle braking systems and repair procedures

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Demonstrate knowledge of motorcycle braking system repair procedures. Performance criteria 2.1 Fault diagnosis procedures are described in accordance with service information. Range safety procedures when diagnosing, logical inspection procedure, checking fault codes, recognising wear, damage, scoring, poor adjustment, seized parts, corrosion, air in hydraulics, brake squeal, brake shudder, brake grab. 2.2 Hydraulic cylinder inspection procedures are described in accordance with service information. Range layout of components, cylinder operation, cleaning methods, measuring wear, attention to cleanliness, limits of corrosion and scoring. 2.3 Brake repair procedures are described in accordance with service information. Range repairing cylinders and callipers, safety implications, replacing cables and rods, fitting shoes and pads, adjusting brakes, replacing brake fluid, clearing fault codes, testing brake operation. Please note Providers must be accredited by NZQA, or an inter-institutional body with delegated authority for quality assurance, before they can report credits from assessment against unit standards or deliver courses of study leading to that assessment. Industry Training Organisations must be accredited by NZQA before they can register credits from assessment against unit standards. Accredited providers and Industry Training Organisations assessing against unit standards must engage with the moderation system that applies to those standards. Accreditation requirements and an outline of the moderation system that applies to this standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The AMAP also includes useful information about special requirements for organisations wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource requirements

MZ 125 SXJSM Repair Manual

0

Filed Under (MZ) by admin on 18-11-2010

download
Front suspension · Design Telescopic fork · Spring travel 220 mm Rear suspension · Design long swinging fork · Spring travel/adjustment 220 mm/adjustable spring base Steering bearing Deep groove ball bearing Clutch lever and throttle twist grip · Play in the clutch lever 3-5 mmattheendofthe clutch · Play in throttle Bowdencable 2-3 mmatthetwist grip flange Wheels – spoked wheels Variant MZ125 8X Variant MZ125 8M Front tire 90/90 -21 110170-17 Tire pressure 190 kPa/1,9 bar/28 psi 180 kPal1,8 bar/26 psi Rim size 1.85×21 3.00 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Rear tire 120/80 – 18 130170-17 TIre pressure (value at perm. axle load) 200 (250) kPa/2 (2,5) bar/29 (36) psi 230 (260) kPal2,3 (2,6) bar/33 (66) psi Rim size 2.50 x18 3.50 x17 Rim wobble limit vertical 0,5mm 0,5mm side 0,5mm 0,5mm Front wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper I and manually operated cylinder · Outside diameterxplate thickness 280x4mm · Thickness of the brake pad 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 11 mm · Brake caliper cylinder inside diameter 2×25,4 mm · Brake fluid DOT4 Rear wheel brake · Design hydraulic single-disc brake with a two-piston floating caliper and manually operated cylinder · Outside diameterxplate thickness 220x4mm · Thickness of the brake pad (wear limit) 5,Omm · Wear limit <2,Omm · Main brake cylinder inside diameter 13mm · Brake caliper cylinder inside diameter 2x 25,4mm · Brake fluid DOT4 Brake level and brake pedal · Play in brake lever 2-5 mmattheendofthe brake lever · Position of brake pedal 25 mmunderthe footrest rubber surface

Harley-Davidson CHROME/ BLACK FRONT MASTER CYLINDER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-10-2010

download
if this is a master cylinder cover replacement, start with step 1. If this is new installation for a hydraulic clutch kit, go to step 3. D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Clean front master cylinder cover, then remove the two screws that hold the cover in place. 2. Remove the original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. See Service Parts illustration. Install the new cover screws (1) and tighten to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) NOTE The cover is lab led for D.O.T. 4 brake fluid. Install this cover on reservoirs filled only with D.O.T. 4 brake fluid. Do not mix grades of brake fluid. as they are not compatible and could cause equipment damage. SERVICE PARTS See Figure 1 and Table 1