1998-2001 HONDA VFR 800 Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 14-12-2011

download
Identify the key components that complete our brake line kit: You should have nine (9) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) single bleeder bolt three (3) drawings, and a picture CD. There are also a total of forty (40) washers and two (2) “olive” conic inversors. Thirty six washers will be used, and two olives. The rest are spares.Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G are installed on the front of the motorcycle, while brake hoses (H and I) are installed on the rear. Each label will reference a different drawing, which will show you the location of the key brake system
components.Step 3: To ensure no paint damage from a brake fluid spill, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a couple pictures, in case you need to re-install. Step 4:Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G. Locate lines A. this hose will run from the master cylinder down to the right caliper and across the fender through the C-CLIP down to the left caliper. Line D. will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame female fitting will thread into the male with a (OLIVE) this O.E.M tubing travels to the proportion valve. Line F will run from the left caliper up through the C-CLIP to the left upper frame female fitting and thread to the male with a (OLIVE) this tubing travels to the rear master cylinder. Locate and install line E; this hose will run from the lower delay valve down to the right caliper. locate and install line C& G; line G will travel from the bottom (left) mounting point on the left caliper, to the upper inner mounting point of the left caliper this line joins line C with a double banjo bolt. line C will travel from the inner left caliper through the C-CLIP across the front fender to the inner mounting point of the delay valve

1997-2003 HONDA CBR1100 XX Black Bird Complete Brake Line Kit INSTALLATION

0

Filed Under (Honda) by admin on 05-11-2011

download
identify the key components that complete our brake line kit: You should have eleven (11) hoses, one (1) double banjo bolt, fourteen (14) single banjo bolts, (1) Installation CD. There are also a total of Thirty Six (36) washers and two (2) “olive” conic inversors two (2) c-clips. Thirty Two (32) washers will be used, and two olives. The rest are spares. Step 2: Familiarize yourself with the brake lines, which are labeled for application. Lettered brake hoses A, B, C, D, E, F, G, H, K, I are installed on the front of the motorcycle, while brake hoses (J and K) are installed on the rear. Each label will reference a different drawing, which will show you the location of each brake line. Step 3: To ensure no paint damage from brake fluid, completely cover the bike. This process can be messy, and brake fluid WILL drip! Step 3: Dry out (bleed) your OEM hoses, and take note of how the stock system is installed. You may want to take a
couple pictures, in case you need to re-install. Step 4: Remove the stock hoses on the front of the motorcycle, and replace with Galfer hoses labeled A,B,C,D,E,F,G,H,K,I. Locate lline A. this hose will run from the master cylinder down to the Galfer t-block
joining line B to the right caliper upper mounting point. Line C will travel across the fender down to the left caliper upper mounting point. Line D will run from the (DELAY VALVE) up through the C-CLIP to the right side upper frame O.E.M tubing. The female fitting will thread onto the male with a (OLIVE). This O.E.M tubing travels to the rear master cylinder. Line E Travels from the lower delay valve down to the right caliper lower mounting point. Line F will run from the (SECONDARY MASTER CYLINDER) up through the C-CLIP to the left upper frame O.E.M tubing. The female fitting will thread onto the male with a (OLIVE).This tubing travels tothe rear delay vale

YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

SUZUKI SV650/ S PERIODIC MAINTENANCE CHART

0

Filed Under (Suzuki) by admin on 26-02-2011

download
Item km miles months 1000 6000 12000 18000 24000 600 4000 7500 11000 15000 1 6 12 18 24 Air cleaner Spark plugs Tappet clearance Engine oil Engine oil filter Fuel hose Engine idle speed Carburettor synchronization Evaporative emission control system PAIR air supply system Throttle cable play Clutch cable play Radiator hoses Engine coolant Drive chain Brakes Brake hoses Brake fluid Tires Steering Front forks Rear suspension Exhaust pipe bolt & nut Chassis bolt & nuts – - – R R – I I I – - I I – - – I – - T T Replace every 4 years Replace vapor hose every 4 years – - I – I I I – - Replace every 2 years Clean & lubricate every 600 miles (1000km) Replace every 4 years Replace every 2 years R R R R – - R – I I R I I R I R – Inspect and adjust, clean

Honda GL1500 EZ Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Use the Parts Checklist included with your hardware to verify the contents of the box 2. Remove the front wheel, fender, forks and triple clamps as shown in the Honda Shop Manual. Torque head bearings to 30 ft-lb. 3. Replace the stock fork caps using new seals with the extended caps provided. If you do not already have Progressive fork springs we suggest they be installed for the best results. 4. Install the new triple clamps. Remember to grease the new lower steering bearing. 5. Install the forks into the new triple clamps. Be sure to torque all pinch bolts to factory specifications. Do not over tighten as this can cause undue stress on the new triple clamps. 6. Check the steering lock action by turning the forks fully in both directions. Because of manufacturing tolerances in the fairing mounting bracket the fork tubes sometimes make contact with it at full lock. Usually this can be overcome by giving the handlebar a slight push while engaging the lock. 7. Because the fork tubes are now longer than stock, DO NOT use the clamps that held the brake lines to the stock lower triple clamp. Some models have a temperature sensor mounted under the fairing that may interfere with the plastic cable guide. If interference is noted trim the guide as required. 8. Install the fender and wheel assembly. Be sure the brake hoses are routed to allow full travel of the forks. It is necessary to trim the two upper ears off of the fender upper cover to prevent contact with the fairing during turns. 9. If you have questions please call our EZ-Steer Maintenance The bearings in your EZ-Steer rake kit are normal wear items, not subject to replacement under Champion’s one year Limited Warranty for the product. Failure to follow your motorcycle manufacturer’s recommendations for periodic OEM triple-tree maintenance will accelerate the wear on these bearings. Checking/adjustment of the steering stem nut torque, with the front end lifted, in accordance with your motorcycle manufacturer’s recommendations, is key to reliable bearing service