Harley-Davidson HEAT DEMONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
1. Remove the Right Handlebar Control, upper and lower switch housing screws, and Right Grip from the Handlebar according to the service-manual instructions and set aside or leave hanging. Remember to insert a spacer between the rear brake light switch and the lever to keep the switch from being broken. 2. Remove the Left Hand switch housing from the handlebar according to the service-manual instructions. 3. Using a T27 TORX drive head remove the half of the clamp that secures the clutch hand lever to the handlebar and discard. The Heat Demon controller will replace this clamp when finishing the installation. Separate the clutch hand lever assembly from the handlebar and move away from the bar. 4. Mark the location of the Left Grip and remove it by twisting, heating or with air pressure. Almost all grips can be removed without damage. If this does not work it may be necessary to cut the grip for removal. 5. A hole needs to be drilled in the bottom of the handlebar to route the power wires and wires from the Controller. The location of the hole should be in the groove or recess on the bottom of the handlebar under the Left Switch Housing at the end of the groove toward the grip. Start by punching a hole location with a center punch to pierce the chrome. Use safety glasses that completely cover the eyes to protect from steel chips while drilling! Start with a small drill like a 3/32″ size to make the initial hole. Then use progressively larger drills or a step drill to increase the hole size to 5/16″. After the hole is drilled use a round file or deburring tool to remove the sharp edges. 6. Uncoil the plastic snake from the kit and run it from the right end of the handlebar out the left end. Twisting the snake or inserting it vertically versus flat can help to push around the corners. 7. Attach the white and yellow wires from the Right Grip Heater (Item 3) to the hole in the plastic snake and pull them through the bar so they exit the left end. (See drawing below) 8. Push the right heater into the handlebar by squeezing it together and sliding it fully inside of the bar. The end of the heater with the orange cap should be pushed in first. Cut the white and yellow wire to extend 4 inches beyond the left end of handlebar. 9. Install the Right Throttle Control and Grip according to the service manua

2000-2003 KTM MXC / EXC Dual Sport Kit Installation Manual

0

Filed Under (KTM) by admin on 01-02-2012

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, fuel tank, and side panels. Stock switch Bracket Photo 2 EXC – Unplug and remove the stock headlight. (Photo 2.) Unplug the stock three-pin taillight connector and pull the taillight wires back to the rear of the airbox temporarily. MXC – Remove the stock front number plate. 3. Make sure the stock battery is oriented in its mounting bracket as shown with the positive terminal on the left side of the bike (as viewed if sitting on the bike). If not, remove and spin it 180 degrees. Photo 3 4. MXC ONLY! (EXC skip this step.) Locate the stock lighting wiring harness zip-tied under the frame back-bone (See Photo 4). Remove the securing zip-ties and route this wiring forward to the area behind the headlight. Route along right side of frame using factory wire- guide clamp. 5. Brake Light Switch Installation: The KTM kit uses a hydraulic brake-switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the stock banjo bolt and replace with the hydraulic switch as shown. Make sure to install

Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ¼” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Honda XR 400 Removal and Installation Manual

0

Filed Under (Honda) by admin on 09-12-2011

download
Turn Signal Switch Installation Front Wiring Connections Field Effect Transistor Installation Taillight Installation: Install the Acerbis DOT taillight over the empty well left in the stock fender using the two 5 x 20 mm bolts and 6 x 16 mm bolt found in the parts bag. Position the taillight over the previous taillight mounting well and transfer the hole locations for the top mounting holes onto the fender with a felt pen or snap punch (Photo 3) so that they are 3/8 of an inch above the edge of the taillight opening as shown in Photo 3. Drill two 3/16 inch holes for the top mounts. Attach the taillight using the top mounting screws, then pull the license plate holder down toward the bottom of the fender so that the taillight is pulled as horizontal as possible. Transfer drill a 1/4” hole at the bottom mounting location with the taillight in this position. When installing the bottom license plate mount bolt, make sure to install the 6 x 16 mm bolt from the bottom up to minimize the opportunity for the tire to grab it. Run the taillight
wires along the left frame rail using the stock wire clamps to support it. 8. Rear Turn Signal Installation: Turn signal mounting requires that you drill a 3/8 inch hole in either side of the rear fender near where it meets the side panels. You can achieve a clean,
durable installation using this mounting location. Mount the rear turn signals by drilling a 3/8 hole in the rear fender in the location shown in Photo 5, 3-3/4 inches back from the front edge (pointed tip of fender where it meets the side panel) and 2-3/4 “ up from the bottom edge Brake Light Switch Installation

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

HARLEY DAVIDSON DYNA GLIDE BRAIDED REAR BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
INSTALLATION Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) Drain Brake Fluid 1. Pop off bleeder nipple cap on rear brake caliper. 2. Install one end of a length of plastic tubing over caliper bleeder valve. Place free end of the tubing in a suitable container. 3. Open the bleeder valve about 1/2-turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not reuse brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. See Figure 1. Disconnect wiring harness connectors from brake light switch spade terminals.

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

HARLEY DAVIDSON SPORTSTER BRAIDED REAR BRAKE LINE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
This kit fits 1988-2003 XL models. INSTALLATION Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Drain Brake Fluid 1. Remove bleed screw cap on rear brake caliper. 2. Install one end of a length of plastic tubing over caliper bleeder valve. Place free end of the tubing in a suitable container. 3. Open the bleeder valve about one-half turn and pump the brake pedal to drain the brake fluid out of the rear brake system. Do not re-use brake fluid. Remove brake line components carefully. Damage to seating surfaces can cause leakage. (00320a) Remove Existing Rear Brake Line 1. Disconnect wiring harness connectors from brake light switch spade terminals. 2. See Figure 1. Remove screws from the three P-clamps and one bracket used to secure brake line to motorcycle. a. Save all screws except bracket screw and save stock P-clamp, located at the right side sprocket cover, for later use. b. Do not mix up the screws. The screws must go back into the same threaded hole in which they were removed. c. Discard remaining two P-clamps. 3. Note brake line routing, then remove existing brake line. NOTE This kit contains clamps to replace the original equipment clamps removed, except for the small clamp on the right side sprocket cover.