2000 – 2005 Celica REAR DISC BRAKE PAD INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
A. Install the two brake pads with the anti-squeal shims to the brake caliper. B. Install the two (2) guide pins to fix the brake pads. 2. Install spring No. 1. A. Hook the spring upper portion to guide pin No. 1. Spring No. 1 B. Hook the spring lower portion to the center hole of the brake pad. 3. Install spring No. 2. A. Hook the spring upper portion to guide pin No. 1 Secure the guide pins with the retaining clip. A. Insert the retaining clip end into the hole of guide pin No. 1. B. Insert the other clip end into the hole of guide pin No. 2. NOTE: The retaining clip should be fully inserted into guide pin No. 1 and No. 2. If NOT, the guide pins will come off and the brake caliper will be damaged

TOYOTA HILUX VEHICLES INSTALLATION, SERVICE MANUAL

0

Filed Under (Toyota Manuals) by admin on 02-06-2011

Download
A SIBSо is simple to install, simple to operate and increases reliability significantly. It utilizes conventional ctuation and can be applied to any rotary equipment, large or small, industrial or automotive, on and off road. A SIBSо incorporates a service brake, a park brake and an emergency brake into a single brake. It is an Australian nvention that is patented worldwide. It is the only brake in the world that is able to perform consistently every time,
regardless of its environment, while requiring minimal maintenance throughout its life under the most demanding braking applications. A SIBSо set comprises four individual brakes. Each fully sealed brake consists of a sliding rotor, brake pads and a small quantity of specially formulated SIBSо fluid. Because it is fully sealed, there is no ngress of foreign substances, and brake debris is not released into the atmosphere.

HARLEY DAVIDSON REPLACEMENT BRAKE PAD/PASTE KIT

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
REMOVAL Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) 1. Remove the brake caliper and pad following the instructions in the service manual. Discard pin and clip. For Kit 41852-08A: Discard brake pads. INSTALLATION Always replace brake pads in complete sets for correct and safe brake operation. Improper brake operation could result in death or serious injury. (00111a) Prepare the Replacement Brake Pads 1. Remove paper backing from the mask. 2. See Figure 2. Carefully align and apply the mask (1) to the non-friction side of the brake pad (Figure 1, Item 2). NOTES Gloves are recommended when applying the brake pad paste to keep hands clean. 3. See Figure 4. Apply paste (6) in the mask holes until the holes are filled with paste. NOTE To prevent brake paste from transferring to other surfaces, do not apply paste thicker than specified. 4. See Figure 3. Wipe away excess paste with scraper (1) until the paste is the same thickness as the mask (2)

HARLEY DAVIDSON REAR BRAKE CALIPER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Prepare the Motorcycle for Service To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Follow the Service Manual instructions to disconnect the negative (-) battery cable. Remove Rear Brake Caliper Remove the Brake Pads 1. For models equipped with saddlebags: Remove the right-side saddlebag. Refer to the SADDLEBAGS section of the Service Manual. 2. Remove the rear master cylinder reservoir cover. 3. Pry both the inside and outside pads away from the brake disc and toward the caliper assembly to push the caliper pistons back into their bores. Use steady pressure to prevent scoring the brake disc. Pry between the pads and the brake disc. 4. When the pistons are fully retracted into their bores, pull the pad pins out to allow the pads to drop from the caliper assembly. Note the pads’ original orientation for installa- tion. 5. Install the cover on the rear master cylinder reservoir. NOTE Place a container under the brake caliper to catch brake fluid released when removing the brake line from the caliper. 6. Remove the banjo bolt fastening the rear brake line to the stock rear brake caliper. Save the banjo bolt for brake caliper installation and discard the two steel/rubber gas- kets. Remove the Stock Rear Brake Caliper 1. Apply isopropyl alcohol to the rubber bumper on the brake caliper to ease removal. 2. Lift the stock rear brake caliper toward the front of the motorcycle. The notch in the caliper must clear the weldment on the swing arm. 3. Remove the caliper from anchor weldment on rear swingarm. Inspect Pad and Pins 1. Inspect the brake pads. If friction material above the backing plate on either pad is 0.040 in. (1.02 mm) thick or less, replace the set. Follow the instructions in the Service Manual. 2. Inspect pad pins for wear and grooving. If wear is more than 0.015 in. (0.38 mm), replace both pins. 3. Inspect the brake disc and, if necessary, follow the instructions in the Service Manual to replace the brake disc. Install the Rear Brake Caliper NOTE Pay close attention to all warnings, cautions, and torque specifications in this instruction sheet and in the service manual when installing this rear brake caliper. NOTE Apply isopropyl alcohol to the rubber bumper for ease of installation. 1. See Figure 1. Position the caliper (1) between the brake disc and the rear fork. The weldment on the fork should fit between the notch and rubber bumper on the caliper. Verify that the full length of the rubber bumper contacts the underside of the weldment

Incoming search terms:

Stinger Folding Motorcycle Trailer Review And Specifications

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
trailer with which to haul your machine(s). The steady stream of four-wheelers trailering two- wheelers to Daytona Bike Week proves that, for a considerable number of us, Mother Nature’s elements are sometimes best enjoyed upon reaching our destination, rather than experienced while traveling toward it. Travel aside, motorcycle trailers are handy, even indispensable, for getting asickly motorcycle to the shop, or to avoid committing the better part of a day waiting while the dealer installs new tires and brake pads. Finally, we find atrailer is preferable to a pickup truck for motorcycle transport, especially when singlehandedly loading/unloading. The problem for many of us is where do we find the space to park this little- used device? No matter if it’s a flatbe Rod Haskins, owner of metal bender Maintenance &Fab in Richmond, California, isn’t a rider himself, but his research indicated a market existed for a sturdily built, full-sized motorcycle trailer that folded compactly when not in use. Learning of a dormant but clever design developed by an agricultural trailer company, Haskins struck a deal, made several improvements and the Stinger Trailer was born. Werecently spent some time with a Stinger and found it to be a clever product. The Stinger arrived folded and secured to a wooden pallet. Assembly was simple, and within 20 minutes we had the 180- pound trailer ready to tow. The trailer is not towable in the folded position—that’s for storage only. Aone-car garage, home to our full-sized Chevrolet, couldn’tnormally house a motorcycle trailer, too. But the folded Stinger squeezed in nicely

Incoming search terms:

APRILIA QUASAR 50-100-125-180 maintenance Manual

0

Filed Under (Aprilia) by admin on 26-11-2010

download
CHANGING ENGINE OIL CAUTION In case of oil leakage or malfunctions, contact an Aprilia Authorised Dealer . Do not dispose of oil in the environ- ment. Dispose of engine oil – stored in a sealed container – through the nearest waste oil reclamation firm or through the supplier. Carefully read page 34 (MAINTE- NANCE) To change engien oil: ◆ Ride for a few kilometres until engine reaches the operating temperature, then stop the engine. ◆ Position a graduated container (1), under the drain plug (2). ◆ Loosen oil filler plug (4) and drain plug (2). ◆ Let oil flow out of the sump. ◆ Loosen oil filter (3) and carefully clean it. ◆ Refit the filter and tighten fully. ◆ Tighten drain plug (2) and pour recommended oil into filler plug (4), see page 58 (LUBRICANT CHART). ◆ Tighten the filler plug. CAUTION Carefully tighten filler and drain plugs and ensure oil does not leak out. Periodically check for leaks at the casing cover gasket. Do not use the vehicle with insufficient lubrication or with contaminated or unsuitable lubricants, since this would cause early wear of the moving parts and may also cause irreparable failures Fluid reservoir (1) is under rear right wheelhouse. CAUTION Position the vehicle on firm and flat ground. ◆ Make sure that the fluid contained in the reservoir exceeds the ” MIN ” mark stamped on the reservoir. MIN = minimum level. WARNING Do not use the vehicle if the braking system is leaking fluid. CAUTION Do not use the vehicle if the fluid is below the “MIN” mark. 1
27 use and maintenance Quasar 50 – 100 – 125 – 180 CAUTION Brake fluid level decreases as the brake pads wear down. Should the level be too low: ◆ Check the brake discs and pads for wear, see page 27 (CHECKING THE BRAKE PADS FOR WEAR) If the pads and/or the disc do not need re- placing: ◆ Contact an Aprilia Authorised Dealer that will top up the fluid. WARNING Check the brake for proper operation. When the brake lever has exceeding travel or if you notice a loss of braking, contact an Aprilia Authorised Dealer . The braking system may need bleed- ing. CHECKING THE BRAKE PADS FOR WEAR Carefully read page 26 (BRAKE FLUID – recommendations) , page 26 (DISC BRAKES) and page 34 (MAINTE- NANCE). Periodically check brake pad wear. The rate at which brake pads will wear depends on vehicle usage, riding style and road surface condition. Outlined below is a quick brake pad inspection procedure: ◆ Visually check between brake disc and pads, check both pads (1) looking from the bottom at the rear end. ◆ Should friction material (of even one pad only) be worn down to 1.5 mm of thickness, have both pads replaced

Incoming search terms:

Harley-Davidson CHROME FRONT BRAKE CALIPER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
See Figure 1. Refer to FRONT BRAKE CALIPERS: REMOVAL in the Service Manual, and follow the instructions to: a. remove the banjo bolt with bleeder valve (2) and both gaskets (4), and b. detach the front brake line (3) from the caliper. c. Discard the gaskets. For this installation, the banjo bolt (2) can also be discarded. d. Remove the caliper mounting bolts (1). Lift the brake caliper assembly upward to remove it from the brake disc. -J03529 1 of 4
2 5 3 4 1 is04104 1. Mounting bolt (2) 2. Banjo bolt with bleeder valve 3. Brake line 4. Gasket (2) 5. Screen cover Figure 1. Remove Existing Caliper 2. Remove the brake pads from the caliper. Refer to BRAKE PADS AND DISCS: BRAKE PAD REPLACEMENT, FRONT BRAKE CALIPER in the Service Manual. a. Remove the screen cover (5) from the caliper. b. See Figure 2. Note the orientation of the brake pads, and remove the retaining clip (2), pad pin (1) and brake pads from the caliper. Also note the position of the brake pads at removal, so they can be installed back in the same location. 3. Repeat the procedure for the opposite-side caliper. 2 1 is04105 1. Pad pin 2. Retaining clip Figure 2. Front Caliper Pad Pin Pad and Pin Inspection 1. Refer to BRAKE PADS AND DISCS: INSPECTION in the Service Manual, and follow the instructions given to inspect the brake pads. If any front brake pad is worn to 0.5 mm (0.020 inch) or less above the backing plate, replace all four front pads. 2. Inspect the brake disc thickness, lateral runout and warpage. If necessary, follow the instructions in the Service Manual under FRONT WHEEL to replace the discs. Chrome Caliper Installation 1. See Figure 3. Obtain the correct-side new chrome caliper assembly from the kit. Remove the screen cover (5), retaining clip and pad pin (4) from the caliper. NOTE Do not remove the shipping plug protecting the brake line threaded hole until ready to install the brake line. 2. Place the caliper over the brake disc with the brake line threaded hole (protected by a shipping plug) facing upward. 3. See Figure 1. Obtain two of the brake caliper mounting bolts (1), removed earlier. Loosely install both bolts through the front fork and into the chrome caliper. Alternately tighten the mounting bolts to 38.0-51.5 Nm (28-38 ft-lbs) . 4. Install the brake pads removed earlier or, if necessary, new brake pads into the caliper. 5. See Figure 2. Install the new pad pin (1) through the inner and outer brake pads. Tighten to 8.5-11.5 Nm (75-100 in- lbs ) . 6. Install the new retaining clip (2) onto the pad pin. NOTE Ensure that the screen cover is oriented with the single tab end up, and the double tab end down. 7. See Figure 1. Install the new screen cover (5) onto the caliper.

Incoming search terms:

Kawasaki Mean Streak 1500 And 1600 BIG SOFT THICK BLANKET Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Place a BIG SOFT THICK BLANKET over your GAS TANK , (LET’S CUT TO THE CHASE, THE MAIN THING IS TO PROTECT THE TANK! ! ! ! ) . 2) You will have to jack up the motorcycle. The best way to accomplish this is with a motorcycle/ATV lift. They are available for a little as $89, and are really an essential tool for maintaining your motorcycle. 3) Remove the stock turn signals completely. They will have to be replaced to do this modification. You may want to install the Kewlmetal turn signal mounts (item #153 or 185) and bullet style signals lights after your fork tubes are in place. 4) Per the Kawasaki service manual, remove the front wheel and be sure to take note of which spacer goes where. Refer to the Service manual for furtherinformation. 5) Remove the front fender Be very careful so you don’t scratch thepaint on the front fender while removing it, the 2 plastic rings holding the front brake lines in place on the front fender will pull out, just make sure to leave them on the lines so they don’t get lost. Now remove the 2 fork guards. 6) Remove the brake calipers and secure the brake pads if necessarywith tape or wire so they don’t fall out. This would be a good time to inspect them for wear, and replace them if necessary. **NOTE** Do not squeeze the front brake lever after you have removed the front wheel. Doing so will cause the calipers to close and then you will have to spread them apart prior to re- assembly. 7) Loosen the bolts on the RIGHT side of the upper and lower tripletree clamps. The fork assembly should drop down. Remove the fork assembly from the bike. 8) Clean the stock fork assembly thoroughly. **NOTE** This kit contains 8 rubber O-rings, (6) Small ones and (2) Fat ones, it is important that these (8) O-rings are placed in the right place for the correct function of the Fat Fork Tubes 9) Slide one of the Small O-rings over the top of the fork assembly until it reaches the bell at the bottom of the shock.

Incoming search terms: