HARLEY DAVIDSON FXSTD DETACHABLE WINDSHIELD AND DOCKING HARDWARE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
INSTALLATION NOTE Use the Docking Hardware Kit to assemble two upper and two lower clamps. See the Service Parts illustration. The upper clamps use a mounting pin (4) and the lower clamps use a button head screw (5) to fasten the windshield mounting bushing. 1. Assemble the windshield docking hardware as follows: a. Install a larger chrome washer (6) and bushing (7) onto a button head screw (5). Thread the screw into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. b. Install a larger chrome washer (6) and bushing (7) onto a mounting pin (4). Thread the pin into the boss on one of the clamps (1), and tighten finger tight. Repeat for a second lower clamp. 2 1 3 4 4 5 is 02187 1. Upper clamp 2. Lower clamp 3. Fork tubes 4.1/8 inch (3 mm) approximately 5.3.0 inch (76 mm) Figure 1. Installing Clamps NOTE Place shop rags on the headlamp, front fender and front of the fuel tank to prevent scratches to these components. Be sure the windshield assembly does not contact chrome or painted parts. Contact will cause scratches to chrome or painted parts. 2. See Figure 1. Install a lower clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the top of the lower triple clamp, then finger tighten the lock nut. Repeat with the second lower clamp and fork tube. NOTE Keep front wheel straight to prevent brackets from scratching fuel tanks. See Figure 1. Install the clamps on the fork tubes so the bushing center lines are 3 inches (76 mm) apart. 3. Install an upper clamp onto a fork tube using a smaller chrome washer and lock nut from the kit. Adjust so the clamp is approximately 1/8 inch (3 mm) from the bottom of the upper triple clamp. Ensure that the center lines of the upper and lower bushings are 3 inches (76 mm) apart, then finger tighten the lock nut. Repeat with the second upper clamp and fork tube

HARLEY DAVIDSON SOFTAIL DETACHABLE SIDEPLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
Kit Contents See Figure 5 and Table 1. INSTALLATION Sissy Bar Installation to Sideplates 1. See Figure 5. Insert the legs of the sissy bar upright (A) all the way into the channels (B) of the sideplates (1 and 2) as shown. 2. Apply a few drops of Loctite 262 – Red to the threads of the button head screws (4). Thread the screws into the holes in the sideplate channels, and tighten to 96-120 in-lbs (11-14 N-m) . Sissy Bar and Sideplate Installation to Docking Points 3. See Figure 1. While standing behind the motorcycle, place the left-side and right-side front sideplate notches (2) into the front docking points (4) on the fender supports (3). See Figure 2 for views of correct and incorrect sideplate engagement. NOTE Failure to properly align the front docking points and sideplates may result in damage to the rear docking points. 1 3 2 4 is05682 1. Sissy bar and sideplate assembly 2. Front notch 3. Right side fender support 4. Front docking point Figure 1. Place Front Notches into Front Docking Points 4 4 3 2 2 1 1 1 2 is00963 1. Sideplate (right side) 2. Right front docking point 3. Correct: sideplate fully engaged in docking point 4. Incorrect: sideplate NOT fully engaged in docking point Figure 2. Sideplate Fit to Front Docking Points

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

HARLEY DAVIDSON FLSTC, FLSTF, FLSTS BLACK ENGINE GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
The front and/or rear guard(s) can provide limited leg and cosmetic vehicle protection under unique circumstances. (Fall over while stopped, very slow speed slide.) It is not made or intended to provide protection from bodily injury in a collision with another vehicle or any other object. (00022a) Kit Contents See Figure 4 and Table 1. INSTALLATION 1. See Figure 1. Note mounting locations for engine guard. 2. See Figure 2. Hold Engine Guard (1) in place. Attach top center mounting flange of engine guard to cross brace located between front downtubes just below the steering head with panhead screw (4), 5/16 inch washer (3) and 5/16 inch hex nut (2) as shown. Tighten finger tight. is04094 Figure 1. Installed Engine Guard 3. See Figure 3. On left side of the bike, attach the engine mounting guard (1) in the indicated location with a button- head screw (4), 3/8 inch washer (3) and 3/8-16 nylon locknut (2). Tighten finger tight. 4. Repeat installation on right side of the bike, attach the mounting guard in the indicated location. Tighten to 33 ft- lbs (44 N-m). 5. Tighten engine guard left side mounting hardware to 33 ft-lbs (44 N-m). Tighten engine guard top mounting hardware to 19 ft-lbs (25 N-m).

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

Incoming search terms:

DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON LEFT SIDE TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION NOTE While handling and installing tool box, be careful not to scratch surface. 1. See Figure 1. Attach the toolbox (4) to the toolbox mounting bracket (1) using the three pan head screws (2) and Nylock nuts (3) from the kit. 2. Remove the two button head screws (I) which secure left rear fender support (B) to motorcycle frame (C). Retain screws for reassembly. 3. On models with passenger footpegs: a. For FLSTN models: Remove button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E). b. For all other models: Remove the locknut (G), hex head bolt (J), spring washer (H) and footpeg (E). Remove the socket head cap screw (K) that secures the footrest support (F) to the frame (C). c. Remove the two bolts, nuts and washers which secure the bottom of the splash guard to the swingarm. This will allow you to move splash guard when installing the new passenger footrest bolt. d. Retain all removed components. 4. On models with passenger footboards: a. Remove the screw securing the passenger footboard assembly to the frame. Remove the footboard assembly. b. Retain all removed components. 5. Slide the top of mounting bracket (1) between rear fender support (B) and frame (C). Align top holes in bracket with fender support holes. Align lower bracket hole with footrest mounting hole in frame. Install the two screws (I), removed in Step 2, in fender support. Do not tighten screws at this time. Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) 6. On models with passenger footpegs: a. For FLSTN models: Install button head screw (N) and left footrest bracket (O) with attached footrest support (F) and footrest (E) on top of the toolbox bracket (1). Tighten screw to 35-45 ft-lbs (47.5-61.0 Nm). b. For all other models: Refer to instructions in footpeg extension kit, Part Number 49352-00 for installation, and install the extention kit, footrest support and footpeg on top of the toolbox bracket (1). c. Install the two bolts, nuts and washers and secure the bottom of the splash guard to the swingarm. 7. On models with passenger footboards: a. Position footboard assembly, in the same orientation as removed, on top of tool box bracket. b. Install screw removed in Step 4. Tighten to 35-45 ft- lbs (47.5-61.0 Nm)

HARLEY DAVIDSON TOURING LAYBACK LICENSE PLATE MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
This kit fits all 1999 and later FLHR (Road King®) models, FLTR (Road Glide®) and FLHT (Electra Glide® standard) models having license plates measuring a maximum of 7-1/4 x 4-1/4 inches (184 x 108 mm). Also fits 2003 FLHRSEI2 (Screamin’ Eagle® Road King). Does not fit with Detachable Tour-Pak Rack, part number 53276-04. Does not fit 2002 FLHRSEI (Screamin’ Eagle Road King). Kit Contents See Figure 1. INSTALLATION 1. Remove the license plate from the vehicle (if installed). Remove the two hex head bolts holding the original equipment (O.E.) license-plate bracket in place. The bolts and license-plate bracket can be discarded. 2. See Figure 1. Install the new layback license plate holder (1) using the button-head hex socket screws (3) from the kit. Tighten the screws to 19 ft-lbs (25.8 Nm) . 4 1 3 7 5 2 6 is02737 1. License plate holder, layback 2. Foam pad (6) 3. Screw, button head, hex socket (2) 4. License plate frame 5. Set screw, socket head (2) 6. Hex key 7. Reflector assembly, Part Number 59365-07 Figure 1. Layback License Plate Mount Components 3. Position the license plate onto the foam pads (2) of the license plate holder, centering and aligning the plate parallel to the holder edges for best appearance. NOTE Slots in the inside top edge of the license plate frame (4) fit over the two tabs on the top edge of the license plate holder. 4. Hook the top of the license plate frame over the top edge of the holder. Swing the bottom edge of the frame inward, holding the license plate in position against the pads. 5. Use the hex key (6) from the kit to securely fasten the license plate frame to the holder with the two socket head set screws (5)

Incoming search terms:

HARLEY DAVIDSON SISSY BAR SIDE PLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
INSTALLATION NOTE When removing rear fender reflectors, be careful not to damage fender paint. 1. Carefully remove the rear reflector. Remove any remaining adhesive from the back side of the reflector and any adhesive from the side of the fender. 2. See Service Parts Illustration. Remove the screws, washers, locknuts and clipnuts that attach the fender support cover and fender support to fender. Discard the button head screws but retain the washers (A), locknuts (B,C) and clipnuts (D) for installation. NOTE Prior to performing the following step, obtain a little slack for the turn signal assembly by reaching under the fender and bending open the aluminum tab on the clip securing wiring to fender. 3. Remove the locknut (B) from the turn signal stud (E) and gently remove the turn signal assembly from fender support cover, fender support and fender. Save locknut for installation. The turn signal will remain loosely attached to motorcycle by rear directional wire. 4. Carefully position the side plate between fender support and fender. While holding sideplate in position, line up the screw mounting holes and make sure the turn signal wiring passes through the cutout (slot) in the side plate. Coat threads of screws (1 and 2) from kit with Loctite 243 (blue) (Harley-Davidson part number 99642-97) and install locknut and clipnut, however do not tighten completely. 5. Add Loctite 243 (blue) (Harley-Davidson part number 99642-97) to turn signal stud and install through fender support cover, fender support, side plate and fender. Install locknut and tighten to 8-13 ft-lbs (11-18 Nm). Making sure sideplate remains aligned, return to fender support screws and tighten to 8-13 ft-lbs (11-18 Nm). 6. Reach under fender and position turn signal wiring into tab on clipnut. 7. Obtain reflector (3) from kit. Peel off protective strip backing and firmly press reflector (3) to side plate (4), centering reflector horizontally and vertically. 8. Repeat steps 1 through 7 on opposite side of fender

HARLEY DAVIDSON SOFTAIL SPORT LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-02-2011

download
INSTALLATION NOTE Cover the rear fender with a clean shop towel to prevent scratching. Damage to the finish could result. 1. See Figure 1. Remove the four button-head TORX screws attaching the sissy bar (5) to the sideplates (4). Discard the screws 2. Remove the sissy bar and set it aside. For Rigid-Mount Sideplates only: Loosen, but do not remove, the hardware securing the sideplates to the motorcycle. 3. Position the luggage rack between the sideplates. Reinstall the sissy bar into the sideplate channels. 4. Apply Loctite 271 (Red) to the flat head TORX screws (2) from the kit, and insert through the holes in the luggage rack (1), sideplate, and sissy bar. Tighten the screws to 8-10 ft-lbs (10.8-13.6 Nm) . For Rigid-Mount Sideplates only: Apply Loctite 271 (Red) to the screws securing the sideplates to the motorcycle, and tighten to 21-27 ft-lbs (28.5-36.6 Nm) . 5. Remove the backing strip from the two rubber bumpers (3) and install onto the luggage rack. a. Align the notches in the bumper with the bottom edge of the channel on the sideplate. b. Wrap the bumper up the side of the luggage rack channel and across the bottom of the sissy bar. When properly installed the bumpers will cover the lower flat head screws, and will bend around the lower edge of the channel. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) NOTE Maximum luggage rack weight capacity is ten pounds (4.5 Kg)