STEERING GEAR/ STEERING WHEEL REMOVAL AND INSTALLATION

0

Filed Under (Uncategorized) by admin on 05-10-2011

download
TEERING GEAR/STEERING WHEEL REMOVAL & INSTALLATION Page 3 of 4 STEERING GEAR/STEERING WHEEL INSTALLATION PROCEDURES (Cont’d) 2. Center spiral cable. a. Turn the cable counterclockwise by hand until it becomes harder to turn. b. Then rotate the cable clockwise about 2.5 or 3 turns to align the marks. (See Fig. 4) 3. Install the steering wheel. a. Align the matchmarks on the wheel and steering main shaft. b. Temporarily tighten the wheel set nut. c. Connect the spiral cable connector. 4. Bleed Power Steering System (when applicable). 5. Check steering wheel center point. 6. Torque steering wheel set nut. See the applicable vehicle’s repair manual for the torque specification. 7. Install and center steering wheel pad. NOTICE: Make sure the pad is centered and installed to the specified torque. If the pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the wheel pad with a new one. When installing the pad, take care that the wiring does not interfere with other parts and is not pinched between other parts. a) Connect the airbag wiring connector. b) Install the pad after confirming that torx screws are in the screw case. c) Using a torx socket, torque the screws to the specification in the vehicle’s Repair Manual. (See Fig. 5) d) Install the steering wheel lower cover

Incoming search terms:

CCS- 100 ELECTRONIC CRUISE CONTROL INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 10-11-2010

download
UNDER HOOD INSTALLATION Connecting the Cruise Control Cable to the Throttle NOTE: Prior to attaching servo cable to throttle, locate an accessible area to mount the cruise control servo, but do not mount it. Leave the servo in this area (unmounted) and route cable to throttle attachment area. CAUTION: Attach the cruise control cable so that it parallels the existing throttle cable as nearly as possible. Choose a mounting method from the figures below: Attachment area for securing cable Bead Chain Coupling Sleeve (#23) Bead Chain Coupling (#24) 3 BEAD CONNECTOR FIG. 6 FIG. 7 FORD LINKAGE ADAPTOR Rubber Ring WIRE LOOP FOR PULLEY Carburetor Existing Snap-On Throttle Arm On Vehicle FIG. 2 SNAP-ON THROTTLE ARM MOUNT FIG. 3 CLAMP-ON THROTTLE ARM MOUNT Determine a suitable point on the throttle linkage to mount the cable connector. The mounting point chosen should have between 1-1/2″ to 2″ total linkage travel. It must operate smoothly by hand. There should be at least 5 beads between the throttle connector and servo cable end. The cable must pull in a straight line from throttle linkage. Some vehicles that do not have enough total linkage travel have to be connected at the accelerator pedal. The bead chain and servo cable end must be inserted into the bead chain connector. Then the bead chain coupling sleeve must slide over bead chain connector to insure that the end will not hang in the connector. FIG. 1 Cable Bead Chain Eyelet Connector (#25) Pull off Throttle Arm and Insert Bead Chain Connector between it and Carburetor Arm. Be sure additional thickness of adaptor does not bind linkage. 20° Bead Chain Eyelet Connector (#25) Cable Must Be within 20° of same angle as Throttle Rod Throttle Cable Throttle Wire Loop (#29) Barrel Wire Adaptor (#30) WIRE BARREL FOR PULLEY FIG. 5 FIG. 4

Ducati 1098 and 1098S ECU connection Installation Manual

0

Filed Under (Ducati) by admin on 25-10-2010

download
ECU can be connected to AIM loggers in two different ways: directly, or using the connector placed on the dashboard. 2.1. – Direct connection between AIM loggers and Marelli IAW 5AM2 ECU IAW 5AM2 is equipped with two 38 pins connectors, named “Body ” and “Engine” – see below: “engine” is black (on the left). “Body” connector is grey (on the right). To connect AIM loggers to Ducati ECU: • connect AIM cable labelled CAN+ to pin 20 of “Body” connector. • connect AIM cable labelled CAN- to pin 29 of “Body” connector. • Vbatt is on pin 17 (vehicle master switch). 2.2 – Dashboard connector Connector is equipped with 26 pins and it is placed on the back of the dashboard. To connect AIM loggers to ECU using the dashboard connector: • connect AIM cable labelled CAN+ to pin 19 (green/black twisted cable) connector. • connect AIM cable labelled CAN – to pin 26 (grey/green twisted cable) connector. • Vbatt is on pin 23 – red /black cable – vehicle master switch. Warning: to use Marelli dashboard , please remove 120 OHM resistance placed between CAN+ and CAN-; otherwise Marelli dash does not work

Incoming search terms: