MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

Toyota 1/ 2JZE Fitting Guide

0

Filed Under (Toyota Manuals) by admin on 20-06-2011

Download
When installed correctly your VEMS ECU will provide you with long trouble-free
service. Please take time to read this guide, and pay special attention to the section
on Ground Wires. If you have any problems understanding any of the information
here, please contact your VEMS Reseller.
The information contained here should be sufficient to install and run your pre-
configured VEMS and wiring loom. It is designed to compliment the VEMS User
Guide which you should take time to read and refer to as you progress through the
installation and calibration of your VEMS

2003-2007 Victory Motorcycles Installation Instructions for S&S Freedom Performance Tuner

0

Filed Under (Victory) by admin on 31-10-2010

download
Once the download of S&S Freedom Performance Tuner has been installed on your PC, double click the icon on your desk top. Picture 3 illustrates the S&S Freedom Performance Tuner icon. 2- Enter in your Username and Password and click the login button. Your Username and Password for logging in will be the same as your login for Picture 1 Picture 2 Picture 3 3 3 – Once you’re logged onto S&S® Freedom® Performance Tuner, click on the Year and Model of the bike you’re performing the work on in the middle of the page as illustrated in Picture 4. 4 – Click on the Select Vehicle tab at the bottom of the page as illustrated in Picture 5. The tabs on the left side of the page will now be illuminated. Picture 4 Picture 5 4 5- Click on the ECU Reprogramming tab on the left side of the screen as illustrated in Picture 6. 6- In the center of the screen you will now be prompted to enter in customer information, VIN number of the motorcycle you are performing calibration download on, and calibration card number. Select a re-flash file from the drop down list that you want to download into the motorcycle. All the fields must be filled out for you to continue with the download. Picture 7 illustrates the information screen with required fields filled out. Picture 6 Picture 7 5 Note: Due to the limited description space available in the drop down list in S&S® Freedom® Performance Tuner, a detailed list of available calibrations and part numbers can be viewed on the S&S dealer web. Go to ® Calibrations on the left side of the home page. Here you will find a detailed list of calibrations and part numbers for reference only. Picture 8 illustrates the home page and location for the S&S/Victory Calibrations. Picture 9 illustrates the calibrations for reference