2006 2007 Yamaha R6 Front Brake Line Kit INSTALLATION

0

Filed Under (Yamaha) by admin on 25-05-2011

download
Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, two (2) single banjo bolts, and one (1) zip ties. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of most models; we took this piece off to ease installation. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds.

Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

Incoming search terms:

Honda VTX 1300 EZ-Steer Installation Instruction

0

Filed Under (Honda) by admin on 16-02-2011

download
installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1300 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove caps and install supplied extensions to fork tubes using the supplied o-rings. Apply lubricant to o-rings and extensions prior to installing to fork tubes. Reinstall OEM caps and o-rings. • Remove steering lock from OEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft. • Install fork tube covers to bottom clamp if supplied with OEM motorcycle. • Remove OEM nylon tube cover sliders from lower fork legs and replace with supplied sliders, if required for lower chrome covers on C models. See figure on the right. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of extension is flush with top surface of clamp. • Torque dome nut to 75 lb. ft. • Ensure that fork tube extensions are flush with top of upper clamp. Torque upper 8mm bolts to 20 lb. ft and lower 10 mm clamp bolts to 30 lb. ft. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes.

Incoming search terms:

2007 HONDA CBR600RR GALFER Super Bike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. A: Left Caliper (looking at the bike from the front, not seating on it) Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer male adapters, the course thread area threads to the caliper with one washer.Torque level is 12 to 13 ft pounds. See Picture C

2008 Suzuki GSXR 600-750 Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our SUPERBIKE brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) male adapters with two 1.55mm thick washers. There are also a total of (7) washers. five (5) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter with the two thick crush washers provided into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 90 degree banjo from left line, washer, 90 banjo from right line, washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture A) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see picture B) . Thread each female end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using (GALFER’S C-CLIP) to bring the lines together about the same level as the lower triple clamp.

2004-2007 HONDA CBR 1000RR Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Make sure to save the nut and bolt that are currently holding the stock lower section of the hoses. (See picture A) Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo from right line, washer, 40-degree banjo from left line, washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture B) . Make sure that the 90-degree fittings on each caliper are pointing straight up (see picture C) . Thread each banjo end onto the adapter, and torque to 6 ½ Ft pounds. Please tighten the “C” clips on the fender using the OEM bolts we asked you to save above. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, using the galfer 2line clip to bring the lines together and mounting it to the triple tree will insure proper clearness and routing. (See picture D) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with Galfer DOT 4- brake fluid is recommended.

2007 YAMAHA ZX6RR GALFER Super Bike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 1 complete 3 line kit (front Kit), 1 single banjo bolt and 2 lower male adapters. There are also a total of 6 washers, 4 will be used, and 2 are spares. The Left hose has a locating clip and there is a new bolt to bolt that on. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. A: Right Caliper B: Please re-use stock routing clip for right line Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer male adapters, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. See Picture C

2006-2008 Yamaha R6 FK002D512GP ( GP Kit ) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our GP kit: You should have 3-line (front kit), 3 SINGLE banjo bolt and 1 C-CLIP. There are also a total of 8 washers. 6 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the GALFER GP 3-Line starting with the master cylinder line (top line). Torque level is 12 to 13 ft pounds. (See picture A2) Step 5: Install the C-CLIP provided to the lower triple tee top line needs to be held by c-clip [see picture A4&A5] . Lower lines will travel in front of the forks to the calipers; two single banjo bolt (see picture A1) are included for master cylinder to each caliper. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, forty-degree banjo (Top line), and washer. Single banjo bolt torque level is 12 FT Pounds. ( See picture A2 for positioning) Make sure that the [ CALIPER fittings ] on each caliper are positioned [ positioning ] (see picture A6- A7) . Thread banjo bolt into the caliper, and torque bolt to 12 to 13 Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and are clear of any obstructions. Once the lines have been checked for clearance. Proceed to step #6 Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with GALFER DOT 4-brake fluid is recommended.

2007 Yamaha R1 Front Brake Line Kit Installation instructions

0

Filed Under (Yamaha) by admin on 27-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Double banjo bolts must be torqued at 12 FT pounds. (See picture A for sequence) Step 5: Route brake lines below the stock lower triple clamp, and zip tie them together. This will ensure your lines stay in position as the steering moves. Also, make sure the lines are secured beneath the steering stabilizer rod. (See picture C) Step 6: Before installing the lines onto the right and left calipers, replace the OEM bracket with the enclosed “C-clip”. Route the hose through the new bracket and thread the single banjo bolts at each caliper using the following sequence: 20-degree banjo, washer, single banjo bolt, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. (See picture B) Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Step 7: Bleed brake system according to owner’s manual, and build appropriate pressure. Keep in mind your master cylinder is equipped with it’s own bleeder nipple. Finish with Galfer DOT-4 brake fluid

2003-2004 Honda CBR600RR FK003D348SB Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S1) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S2) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 12-degree banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (See picture S3) Make sure that the 40-degree fittings on each caliper are pointing away from the bike just a little bit (see picture S4/S5 for right caliper and S6/S7 for left) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area