HONDA 450E/ S MOUNTING AND ARS ADJUSTMENT INSTALLATION

0

Filed Under (Honda) by admin on 24-12-2011

download
MULTI-RATE SPRINGS AND THE ARS SYSTEM Depending on the application dual–rate springs are fitted on the shocks. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs collapse they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other off road hazards. ARS stands for Adjustable Rate Suspension. ARS is available on some dual-rate spring 4-wheel ATV shocks. ARS differs from spring preload. The ARS system allows the rider to increase or decrease the load-carrying capacity of the shocks by turning a lever. Depending on the application and spring set, the rider can increase the load capacity of the shocks up to 50 percent. The average preloader that makes a half-inch increase in preload will HONDA 450E/S MOUNTING & ARS ADJUSTMENT INSTRUCTIONS Continued on next page. #TRX450 – 5/28/99 #TRX450 – 5/28/99 Fig. 1. Front shock installation. Note that the shock body is at the top with the shaft pointing down. ARS shown is in the unloaded position. Fig. 2. Rear shock mounting with ARS. Position the lever so that it will not come in contact with any vehicle parts around it. The cup can be rotated to reposition the lever if necessary.
increase the capacity of the shocks to only about 5 to 10 percent. ARS allows the shocks to be correct for solo riding, but still handle the increased weight of an added load. ARS can also be employed to stiffen the rates for aggressive riding. The ARS system consists of an indexing lever and a stepped cup that contains the short spring of the dual- rate. The position of the lever in relation to the steps in the cup determines how long the spring set remains on the soft, or initial, spring rate. On most ARS applications, four positions can be selected from full stiff to full soft. Indexing is done in a matter of seconds by rotating the lever or the cup by hand. Indexing the cup to the lever is usually preferable to avoid interference. Adjustment of the ARS system should only be made while the vehicle is unloaded to reduce the load on the springs. NOTE: It is important to make sure that a step in the cup is positioned directly over the tang on the lever. This will prevent damage to the cup and/or lever that can be caused by making partial contact between the tang and a step. In addition, make sure that the lever will not contact any vehicle parts around it, as the suspension moves up. TUNING TIPS—The “softest” setting on the ARS does not mean that the ride will be the most comfortable at that setting. It means that this is the softest spring setting which would be employed on smooth trails or without a load. Excessive suspension bottoming caused by rough conditions or by the addition of a large load will cause a harsh ride when the shock is adjusted to this setting. To eliminate this bottoming, adjust the ARS to the stiffer positions for a more comfortable ride. Hence, sometimes “stiffer is softer.” NITROGEN PRESSURES IN EMULSION SHOCKS

HONDA BRAVO Engine Owner and INSTALLATON

0

Filed Under (Honda) by admin on 08-12-2011

download
The focus of this manual is HOW to operate and service the equipment safely. It is not possible to cover every con-
ceivable situation you can face when using this mower. Therefore use this product only in a manner described in
this manual. Operation or handling the machine in any other manner can lead to serious injury or death. if a
situation is not described in this manual it should be considered dangerous ~ and not be done. If you are unfamiliar with this product make sure that you carefully understand how it functions and practice all operations and handling before putting the machine to use. Familiarize yourself in the presence of an experienced operator. Avoid all situations that are beyond your capability. If you still feel uncertain about the operating procedures after reading these instructions DO NOT operate the machine until you have consulted an experienced operator

WORKS PERFORMANCE STREET TRACKER SHOCKS FOR BIG DOG MOTORCYCLES

0

Filed Under (Tips and Review) by admin on 17-12-2010

download
SHOCK REMOVAL AND INSTALLATION– The shocks are fitted with special length spacers to maintain correct alignment between the frame and the swingarm. If the shocks are removed for service or repair, they must be installed in the correct position. Refer to the diagram on the next page for spacer positioning and layout. NOTE: Misalignment between the mounts on the frame and the mounts on the swingarm can cause binding between the shock shaft and shaft bushing. Misalignment of more than 1/4 inch can cause the shocks to bind up and not function properly. If this binding occurs, the shocks will feel overly stiff and harsh. Follow the procedures below to check for misalignment when installing the shocks. NOTE: The shock bushings are designed to have a certain side-to-side “float” to keep them from binding. As a result, do not grind or file the inner or outer edges of the bushings to make them narrower. The amount of “float” in the bushing set is necessary to ensure smooth operation of the damper assembly. If the shock eyes are tightened metal-to-metal (the outer faces of the eyes to the flanges or washers), this will lead to a harsh, stiff or choppy ride and premature seal leakage or damage to the shafts. MULTI-RATE SPRINGS Depending on each application, single or dual-rate springs are available. Dual-rate springs are just that– a spring set with two separate rates. This is done with a short spring stacked on a longer spring. As both springs compress they produce a soft, or initial, rate. The spring set will maintain this initial rate until the short spring stops compressing. At that point, the spring rate “crosses over” to the stiffer, or final, rate. This multi-rate system allows a soft initial rate for comfort on small bumps, but has the capability of soaking up the big pot-holes and other road hazards. PRELOAD ADJUSTMENT— On Works shocks, threaded preload is standard. (See Fig. 2.) This allows the adjustment of the ride height of the motorcycle. The preload is changed by turning a threaded nut down towards the spring (higher ride height) or up away from the spring (lower ride height). The nut is a right-hand thread. It is used primarily to set the ride height for solo riding, but can also be used when

Incoming search terms:

Kinroad XT250GK (double-seat): Owner's Manual

0

Filed Under (Kinroad) by admin on 30-11-2010

download
Keep Hands and Feet on Controls Always keep both hands on the steering wheel and both feet on the foot controls when driving your BUGGY. It is important to maintain your balance and to control the BUGGY. Removing hands or foot away from the controls can reduce your ability to react control of the BUGGY. 250GK (double-seat): Ownr`s Manual 20 Control Speed Driving at excessive speed increases the chances of an accident. In choosing a proper speed, you need to consider the capability of your BUGGY, the terrain, visibility and other operating conditions, plus your own skills and experience. . Use Care on Unfamiliar or Rough Terrain Before driving in a new area, always check the terrain thoroughly. Don’t drive fast on unfamiliar terrain or when the visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or 250GK (double-seat): Ownr`s Manual 21 holes in time to react.) Never drive past the limit of visibility. Maintain a safe distance between your BUGGY and other off-road vehicles. Always exercise caution and use extra care on rough, slippery and loose terrain. 250GK (double-seat): Ownr`s Manual 22 Do Not Perform Stunts You should always operate your BUGGY in a safe and reasonable manner. When driving, always keep all four wheels on the ground.