Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

2008 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
specified in the ACU regulations. The appearance from both front, rear and profile of machines must (except when otherwise stated) conform to the homologated shape. The appearance of the exhaust system is excluded from this rule. 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT Red background with white numbers – Nitro Newcomers Class White background with black numbers – J&S Championship Class REAR White background with black numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer. The sides of the frame body may be covered by a protective part made of composite material. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Rear sub-frame may be replaced by the later type sub-frame to accept new style bodywork on pre-2006 models, this unit must use the original mounting points. Bolt on accessories to the rear sub-frame may be removed. Front fairing bracket may be altered or replaced on pre-2006 models to accept later bodywork. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm) Every part of the rear fork must remain as originally produced (including rear fork pivot bolt and rear axle adjuster). Rear wheel stand positioning (support) brackets may be added by welding or bolts. Brackets must have rounded edges viewed from all sides. Fastening screws must be recessed. 10. REAR SUSPENSION UNIT

2009 APRILIA RS125 TECHNICAL SPECIFICATIONS

0

Filed Under (Aprilia) by admin on 06-11-2010

download
1. MACHINES Aprilia RS 125 production models, as produced from 01-11-05 and available in the UK via IN Competition from 01-01-06. (any parts exclusive to the older models including the pre-1999 SP model are not permitted to be used on machines in this series). The only eligible models are designated as Euro 2 & Euro 3 New machines are supplied with race kits included through: IN Competition Unit 1 New Lane Burscough Lancs 2. DISPLACEMENT CAPACITY The displacement must remain at 124.9cc and the bore and stroke (54 x 54.5) must remain as originally produced. 3. MINIMUM WEIGHT The minimum weight at post race control must not be less than 102kg , this includes oil and water but excludes fuel. At any time during the event, the weight of the whole machine (including the tank) must not be less than the minimum weight, with a tolerance of 1kg. 4. NUMBER PLATE COLOURS The background colours and figures for Aprilia Superteens are: FRONT RED background with WHITE numbers – Nitro Newcomers Class BLACK background with WHITE numbers – Aprilia Championship Class REAR BLACK background with WHITE numbers – Both Classes Placed in accordance with the ACU regulations. 5. CARBURATION INSTRUMENTS Carburation instruments must remain as homologated. Carburettor jets and needles may be replaced. No modification, polishing or cutting is allowed. Only the 28mm bodied standard carburettor is permitted. Electronic or mechanical enriching devices must remain installed and active (If the carburettor is changed from one model to another, the appropriate wiring loom must also be installed and be operative). Bell mouths must be as originally produced by the manufacturer for the homologated machine. Throttle must be standard, quick action throttles are not permitted.
6. FUEL All machines must function on normal unleaded fuel with a maximum lead content of 0.005 g/l (unleaded) and a maximum MON of 90 (RON 102 max) and be readily available from roadside service stations nationwide. E85 Bio Fuel is also permitted when purchased from normal roadside outlets. 7. FRAME BODY AND REAR SUBFRAME Frame must remain as originally produced by the manufacturer and may not be painted. The sides of the frame body may be covered by a protective part made of composite material of the original frame colour. Nothing can be added by welding or removed by machining from the frame body. Engine mounting brackets or plates must remain as originally produced by the manufacturer. Bolt on accessories to the rear sub-frame may be removed. 8. FRONT FORKS Forks structure (spindle, stanchions, bridges, stem etc) must remain as originally produced by the manufacturer. Standard original internal parts of the forks may be modified. After market damper kits or valves may be installed. The fork caps can be modified or changed to add spring preload/compression and damping adjusters. Dust seals can be modified, changed or removed providing the fork remains totally oil sealed. Any quantity or quality of oil can be used in the front forks. The height and position of the front fork in relation to the fork crowns is free. A steering damper may be added but may not act as a steering lock device. 9. REAR FORK (Swing Arm)

Incoming search terms:

Incoming search terms: