Yamaha WR motorcycle ProEFX 12V Hot Start Installation

0

Filed Under (Yamaha) by admin on 06-01-2012

download
1. Remove seat, tank and shrouds. Remove existing hot start lever, cable and valve from the carburetor. 2. Tip: Clean all dirt from hot start bore and mating surfaces on the carburetor body with gas and a q-tip. 3. Tip: Use a small amount of Teflon tape (one wrap) on the threads of the aluminum mounting nut to ensure a water tight seal. 4. Install the Pro EFX hot start valve in the hot start bore (as shown in picture), with return spring, impact washer and delrin plunger in place. • Tip: Installation of the solenoid valve may require temporary rotation of the carburetor away from the top engine mount bracket. • Install with the solenoid valve assembly disconnected from wiring harness. • Screw in by hand and finish tightening with needle nose pliers. Do not over-tighten. Solenoid valve assembly: 5. Mount activation switch on preferred handle bar location. Pictured on clutch side, in place of the stock kill switch.
6. Route wiring harness around steering column and down frame backbone. Insert battery leads through slot in rubber protective boot. (follow existing wiring to battery) 7. Connect positive (red) and negative (black) leads to motorcycle battery. 8. Connect male and female terminals to wiring harness on previously installed solenoid valve assembly. 9. Depress activation button and listen for valve actuation. Plunger should freely “snap” between open and closed position in hot start bore, as activation button is depressed and released. If you don’t hear the valve “snap” open and closed, follow the trouble shooting guidelines or call /email for support. 10. Maintenance: Periodically ensure proper tightness of solenoid valve in carburetor body as part of standard motorcycle maintenance. Keep the battery terminal connections free from corrosion.

Incoming search terms:

Harley-Davidson S&S Super E and G Series Shorty Carburetors Installation and Jetting Instructions

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
throttle linkage with no cable modification. S&S Super E and G carb kits for 1936 to 1989 Big Twins contain a throttle cable guide (11-2339) designed for butterfly type throttle cables, and kits for 1990 and later Big Twins contain a taller throttle cable guide (11-2338) designed for CV type throttle cables. See Picture 2. The two throttle cable guides are interchangeable on the carburetor body, and can be changed very easily to update older carburetors or to accommodate custom throttle cables which are not stock for a particular year chassis. 1981 to Present Sportster Models Stock Sportster models from 1981 to 1987 have two cable throttle system designed for butterfly type carburetors. Sportsters from 1988 to present have a two cable throttle system designed for use with the stock constant velocity (CV) type carburetor. Since the taller #11-2338 cable guide bracket can not be used on a Sportster chassis due to insufficient frame clearance, throttle cables on Sportsters originally equipped with a CV type carburetor must be changed to butterfly style cables. S&S can supply the correct style throttle cables. See S&S Throttle Cable Application Chart. Picture 2 S&S THROTTLE CABLE APPLICATION CHART Length Total Housing Length Vinyl Housing Part Number Open Side Part Number Close Side Fitment 36″ 32″ #19-0430 #19-0431 For Buell with 7/8″ handlebars 36″ 32″ #19-0432 #19-0433 To ’95 ’81-’85 FX and FL; All ’81-’85 XL (Also pre-’81 w/2-cable throttle housing replaced.) For Buell with 1″ diameter handlebar 36″ 32″ #19-0436 #19-0437 ’96-Up 883-1200 XL 39″ 35″ #19-0434 #19-0435 To ’95 Softail (FXSTC, FXST, FLSTC, FLSTF) ’86-’94 FXR, ’93-’95 Dyna 39″ 35″ #19-0438 #19-0439 ’96-Up Softail (FXSTS, FXSTC, FLSTC, FLSTF) ’96-Up Dyna 42″ 38″ #19-0446 #19-0447 To ’95 custom application 42″ 38″ #19-0440 #19-0441 ’96-Up custom application 48″ 44″ #19-0462 #19-0463 To ’95 All FLT Models 48″ 44″ #19-0464 #19-0465 ’96-Up All FLT Models ” 1996 to Present Buells 1996 and 1997 Buells require special S&S butterfly style throttle cables for Buells, which are compatible with the stock 1996-1997 throttle assembly. 1998 and later carburated Buells require installation of stock 1996 – 97 throttle grip and the special S&S Buell style throttle cables when installing Super E or G carburetors. S&S Throttle Kits S&S throttle kits fit 1″ handlebars and can be used on most chassis. (An adapter sleeve is available for use with earlier, 7 ⁄ 8 ” OEM handlebars originally equipped with internal throttle cable.) Barrel fittings on S&S cables readily “plug in” to S&S Super E, G, and stock H-D 1981-’90 butterfly type carb throttle linkage. Kits include one opening and one closing side cable, left and right grips, and handlebar clamps. Kits with 36″, 39″, 42″, or 48″ length cables are available. Length specified refers to overall cable length. Vinyl covered outer housing is 4″ shorter than overall length

Incoming search terms:

Incoming search terms: