HARLEY DAVIDSON FRONT TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
REMOVAL When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Purge the high-pressure fuel line and disconnect the fuel line following the instructions in the appropriate Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse following the instructions in the appropriate Service Manual. 3. Remove the seat following the instructions in the appropriate Service Manual. Save all seat mounting hardware. NOTE When moving the fuel tank back, do not damage the fuel gauge wires clipped to the frame under the left side of the fuel tank. 4. Remove the front and rear fuel tank mounting hardware following the instructions in the appropriate Service Manual. Move the fuel tank back on the frame to gain access to the tabs on the steering head harness shield. 5. See Figure 1. Disengage the tabs (2) from the holes (3) on each side of the frame and remove the shield (1). 6. Pull the wire harness down from inside the frame enough to disconnect the white (left) [31L] and black (right) [31R] 3-place turn signal connectors. Set aside the frame-side connector halves. 7. Remove the socket terminals from the lamp-side connector halves following the instructions in the appropriate Service Manual. Make note of the wire colors installed in the cavities of each connector, which should be: Left side (white connector): a. Black [BK] wire in cavity 1 b. Violet [V] wire in cavity 2 c. Blue [BE] wire (if installed) in cavity 3 Right side (black connector): a. Black [BK] wire in cavity 1 b. Brown [BN] wire in cavity 2 c. Blue wire [BE] (if installed) in cavity

HARLEY DAVIDSON SOFT LOWER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
This kit fits 1980 and later Touring models equipped with engine guards. It does not fit with mustache engine guards INSTALLATION NOTE Soft lowers should not be used in temperatures above 55 degrees Fahrenheit. Engine cooling air flow will be affected and could lead to overheating and possible engine damage. 1. Apply a light coating of silicone grease to cavities of snaps prior to installing soft lowers on motorcycle. 2. See Figure 1. An opening is provided in the soft lowers for mounting highway footrests (1) to engine guard. If using footrests, mount within the opening to prevent buckling of splash guard fabric. 4. Remove adhesive liner from back of reflector. NOTE The ideal temperature should be at least 60° F (16° C) for proper adhesion of the reflectors. 5. Place reflector on fender and press firmly into position. 6. Let the adhesive cure for 24 hours at no less than 60° F (16° C). 7. Repeat steps for other reflector

SCOOTERS FRONT WHEEL/ FRONT BRAKE/ FRONT SUSPENSION INSTALLATION

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
FRONT WHEEL REMOVAL Jack the motorcycle front wheel off the ground. Remove the speedometer cable set screw and disconnect the speedometer cable. Remove the front brake cable. Remove the front axle nut and pull out the axle. Remove the front wheel. Remove the front brake panel. INSPECTION AXLE RUNOUT Set the axle in V blocks and measure the runout using a dial gauge. The actual runout is 1/2 of the total indicator reading. Service Limit : 0.2mm replace if over WHEEL RIM Check the wheel rim runout. Service Limits : Radial : 2.0mm replace if over Axial : 2.0mm replace if over Screw Speedometer Cable Front Brake Cable Axle Nut Axle Shaft 12 . FRONT WHEEL/FRONT BRAKE/ FRONT SUSPENSION 12-4 FRONT WHEEL BEARING Remove the side collar and dust seal. Turn the inner race of each bearing with your finger to see if they turn smoothly and quietly. Also check if the outer race fits tightly in the hub. Replace the bearings if the races do not turn smoothly, quietly, or if they fit loosely in the hub. BEARING REPLACEMENT Remove the front wheel bearings and distance collar. Bearing Remover Bearing Remover Head, 12mm Pack all bearing cavities with grease. Drive in the left bearing. Install the distance collar. Drive in the right bearing. Outer driver, 32x35mm Driver handle A Pilot, 12mm

Incoming search terms: