HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

BMW F 650 CS Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Connection 11 Engine Freewheel housing and freewheel Nm 35 (clean thread + Loctite648) Engine block Nm 10 Double drive gear on crankshaft Nm 180 (clean thread + Loctite243) Driver to countershaft Nm 140 (clean thread + Loctite243) Pressure plate Nm 10 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Chainwheel to main shaft Nm 140 (clean thread + Loctite243) Signal transmitter Nm 8 Ignition cover Nm 10 Cylinder base Nm 10 Fastener for chain tensioner Nm 40 Oil circuit Oil filter cover Nm 10 Oil pressure switch Nm 12 (clean thread + Loctite243) Strainer cover to housing half Nm 8 Drain plug, on-frame oil tank Nm 21 Engine oil drain plug Nm 40 Oil supply/oil return lines to engine Nm 42 Oil pump cover Nm 6 (clean thread + Loctite243) Oil pressure valve Nm 24 Oil retaining valve Nm 24 Cylinder head Collar nuts for cylinder head Nm 60 Collar screws for cylinder head Nm 33 Machine screws (chaincase) Nm 10 Camshaft bearing cap Nm 10 Chain sprockets to camshafts Nm 60 threads oiled Chain guide to camshaft bearing cap Nm 10 (clean thread + Loctite243)
00.4 Cylinder head cover Nm 10 Machine screw (hole for locating screw) Nm 25 Model F 650 CS Connection 12 Engine electrics Spark plug Nm 20 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Signal transmitter Nm 8 Engine block cover, left/right Nm 10 Starter to clutch cover Nm 10 Positive lead to starter motor Nm 9 Positive contact to starter motor Nm 4 Necked-down bolt, starter housing Nm 6 Cable cover to engine block Nm 9 Cable holder to ignition cover Nm 8 Stator to ignition cover Nm 10 (clean thread + Loctite243) Ignition coil bracket to cylinder head cover Nm 9

Incoming search terms:

Incoming search terms: