Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

Harley Davidson KNIGHT PROWLER BELT DRIVE Installation Procedures

0

Filed Under (Harley Davidson) by admin on 28-02-2012

download
STEP 1: Place bike on suitable stand where rear wheel can be rotated in 4th or 5th gear when necessary. STEP 2: Remove front exhaust pipe. If necessary, remove as a one-piece unit. * Tip – Removing front floorboard will help a lot. STEP 3: Using easiest method – bolt cutter, etc. -remove pushrods and discard. We recommend using the S&S Quickee install pushrods and S&S roller tappets WITHOUT travel limiters. Remove tappet covers and tappets. STEP 4: Remove outer cam cover and rotate engine until timing marks are aligned together. STEP 5: Using Harley-Davidson service manual procedure, retract the outer chain tension shoe. STEP 6: Remove crankshaft and crankshaft sprocket retaining bolts using Harley-Davidson service manual procedure and tools. Continue to the next page for special instructions concerning this step with 06-DYNA & CHAIN DRIVE MODELS and also with 1999 THRU 2006 CHAIN DRIVE MODELS

BMW F 650 GS Repair Manual And Maintenance schedule

0

Filed Under (BMW) by admin on 19-11-2010

download
Replace oil in telescopic forks Check the coolant and restore to correct level if necessary *) Replace the coolant (every 2 years) every 2years Check valve clearances, adjust if necessary Replace the spark plug Drain the outlet hose from the air filter box Replace intake air filter If motorcycle is operated in very dirty or dusty conditions, clean or replace the intake air filter every 10,000 km (6,000 miles); check every 3,000 km (1,800 miles) Replace fuel filter (every 20,000 km/12,000 miles) 20,000 km Check clutch play, adjust if necessary Check wheel spoke tension and tighten if necessary more frequently if motorcycle is ridden in severe off-road conditions Examine brake pads and discs for wear, replace if necessary *) more frequently if motorcycle is ridden in severe off-road conditions Check brake fluid level at front and rear and top up if necessary *) Check for operation of brake system and freedom from leaks; repair/replace if necessary *) Replace the brake fluid at least once a year Replace the primary front/rear brake master cylinder cup (every 40,000 km/24,000 miles on a motorcycle with ABS ) 40,000 km Check wheel bearings and replace if necessary *) Check or, if necessary, replace chain, sprocket, chain guide rollers and pinion *) more frequently if motorcycle is ridden in severe off-road conditions Check chain tension and adjust if necessary *) Check battery acid level, add distilled water if necessary more frequently if motorcycle is ridden in severe off-road conditions Clean and grease the battery terminals, if necessary Check steering head bearings and adjust *) or replace if necessary *) Grease the side and main stands Grease the brake pedal Check bolts and nuts on engine mountings, frame connections, exhaust system mountings, swinging fork pivot, suspension levers, brake pedal, main and side stands and quick-release axles for tightness Final inspection with road safety and functional check

Cobra Vintage Bike Service And Parts Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
BEFORE EACH USE, REMOVE THE COVER PLATE OF THE THROTTLE ASSEMBLY AND CHECK THE THROTTLE CABLE FOR FRAYING. IF THE CABLE SHOWS ANY SIGNS OF WEAR, FRAYING OR UNWINDING, REPLACE BEFORE USE. ALSO CHECK THE CABLE FOR STICKING OR PINCHING ON THE FRAME. IF THE CABLE DOES NOT WORK SMOOTHLY, REPLACE BEFORE USE. IT IS RECOMMENDED THAT THE THROTTLE CABLE BE REPLACED AT LEAST ONCE A MONTH. 2. Change engine transmission oil every 2 to 3 hours. See “specifications” for proper fluid type. Fill to hole. 3. Change fork and shock oil every 9 hours. See “specifications” for proper fluid type. 4. Keep all moving parts sprayed with WD-40 or light oil. 5. Keep ignitions clean and dry. Spray with WD-40. It is very important to keep the ground wire going from the frame to the engine clean and connected. 6. Check all nuts, bolts and screws for proper torque. 7. Check the chain for proper adjustment. See “chain tension” section for details. 8. We recommend 15 pounds of pressure in the rear tire in rainy and muddy conditions and 20 pounds on hard packed conditions or where there are a lot of jumps. 9. INSPECT: • chain rollers • swing arm for stress cracks or signs of fatigue • frame for stress cracks or signs of fatigue • wheels for cracks and signs of fatigue • handle bar clamps • make sure kill switch works • make sure engine is running properly and the carburetor jetting is set correctly

Incoming search terms: