Harley-Davidson BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-04-2012

download
1) Remove the primary chain case cover. Refer to your Factory Service Manual for this procedure. 2) Remove the compensating sprocket nut with a 1-1/2″ socket. A ½” impact gun is best for this task. *) Remove the 1-3/16″ clutch nut. This is a left handed nut so loosen it by turning it in the clockwise direction (as viewed from the left side of the motorcycle). 4) With one hand on the compensating sprocket and one on the clutch assembly, remove the primary drive assembly (compensating sprocket, primary chain, tensioner assembly, and clutch as shown in figure a and set it on a clean surface. 5) Flip the adjuster shoe bracket on the chain tensioner assembly. figure b shows the stock orientation of the adjuster show and bracket. Figure C shows the adjuster show bracket flipped 180°. To flip the shoe bracket, remove the two ¼-28×2 bolts that hold the bracket assembly together. This will allow you to separate the chain tensioner assembly components from the primary chain. Flip the bracket around as shown in figure c . PAGE 4 Figure B Figure A BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS 6) install the new compensating sprocket, chain, and clutch onto the motor sprocket shaft and the transmission input shaft. The flipped chain tensioner assembly (as shown in figure c ) is not ‘captured’ on the primary chain like the stock configuration. Loosely install the chain tensioner assembly onto the anchor plate bolt. Tighten the compensating sprocket nut to 157+ 7 ft-lbs and the clutch hub nut to 75+ 5 ft-lbs using red Loctite on the threads.

Incoming search terms:

Harley-Davidson CHAIN DRIVE INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 15-04-2012

download
1) Assemble & install the chain tensioner assembly over the primary chain as shown in figure 1. 2) Install the compensator sprocket with extender & spacer (numbers 5, 6, & 7, FIG 2)(#7 is not included in this kit), primary chain, chain tensioner, and clutch basket simultaneously onto the motor drive shaft & transmission main shaft. Rotate the chain drive slightly as needed to allow the splines to line-up. 3) Install the chain tensioner nut loosely on the chain tensioner bolt. 4) Install the sliding cam onto the compensator sprocket, & slide the compensating sprocket cover-assembly (#3) over the cam. 5) Apply 2 drops of Rivera “Red” thread-lock on the threads of the motor drive shaft, & install the motor nut loosely with the fingers at this time. The hex spacer (#7) and spacer (#2) as seen in fig.2 are not provided in Rivera Engineering’s chain drive kit. These components are required with some applications, and can be purchased from your local Harley-Davidson dealer. FIG 2 6) Apply 2 drops of Rivera “red” thread-lock on the threads of the transmission main-shaft and loosely install the clutch hub nut (left hand threads). 7) Place the HD “Primary Drive Locking Tool” HD-41214 on the primary chain as shown in figure XXX and tighten the motor sprocket nut to 150-165 foot-pounds. 8)Turn the locking tool 180 degrees and move it to the clutch sprocket. Tighten the clutch hub nut to 70-80 foot pounds (left- hand thread). Adjust chain tension so that the top strand has 5/8″- to-7/8″ of up and down play (cold drive train). Tighten the center bolt nut to 21-29 foot pounds of torque.

Incoming search terms:

Honda XR600/ XR650L Camshaft Installation and removal Instructions

0

Filed Under (Honda) by admin on 05-12-2011

download
Remove the tappet covers. Remove the crankshaft cap and timing hole cap on the left engine case cover. Remove the spark plug. Rotate the engine in a counter clockwise direction. Position the engine at true top dead center (TDC) using the mark on the flywheel. True top dead center occurs when both the intake and exhaust valve are closed when the piston is at TDC. This is technically the end of the compression stroke and the beginning of the power stroke. The “artificial” TDC is during the overlap when both the intake and exhaust valves would be open. Since the rocker arms are located in the valve cover on an XR600, true TDC occurs when the cam lobes are pointed downward when the piston is at TDC. Remove the cylinder head cover. Warning, do not drop the locating dowels into the cam chain cavity. There are two dowels, one on either side of the cover. Remove and discard the gasket. Note the positioning of the cam lobes, this will help during installation of your new Hot Cams camshaft. Note also the location of the sealed bearing on the end of the camshaft and the direction in which it is facing. Loosen the bolts that hold the camshaft sprocket. Remove the lower camshaft sprocket bolt first, it will be necessary to rotate the engine. Rotate the engine back to TDC. Release the spring tension on the cam chain tensioner by lifting the end of the spring out of its hole in the tensioner block. A spring tool is a good method. Be careful not to scar the cylinder head’s gasket surface for the cylinder head cover. Remove the allen bolt that holds the end of the tensioner block shaft
just to the inside of the tensioner block. Note the location of the tensioner block shaft cap ridge. Using a pair of pliers pull the shaft out by grasping the ridge and using a clockwise rotation of the shaft while pulling outward. Pull the tensioner block upwards, out of the cylinder head. Remove the top camshaft sprocket bolt. Pull the sprocket off the camshaft but maintain upward tension, do not allow the chain to sag, it is possible for the chain to “slip” on the bottom sprocket of the crankshaft and change the cam timing. Remove the camshaft. Remove the cam bearings. Set the stock camshaft with the auto-decompression aside. It is not possible to use the auto-
decompression on the Hot Cams so do not attempt to re-install. Use a manual decompression. Install the bearings onto the new Hot Cam

Incoming search terms:

Honda V4 Cam-Chain Tensioner Installation and Removal

0

Filed Under (Honda) by admin on 03-12-2011

download
Stay Organized – Misplaced and mismatched screws can be an expensive nightmare on many levels. Spend a couple bucks on organizing bins of various sizes and keep your uninstalled parts together in a logical sequence. 10 seconds now will save you 10 hours later. • Two wire coat hangers • Full metric socket Set w/ medium and long extensions • Various sizes of flat-head screwdrivers
• Safety wire (optional) • Sharpie pen (optional) • Plenty of towels and rags to wipe hands and surfaces • An extra set of hands
2) Keep records – If a job is complicated it’s easy to get confused with what went where before you took it apart. If you have a small digital camera handy and are unsure about your mechanical skills, snap pictures along the way to record how things looked. 3) Don’t get frustrated – If you start feeling frustrated and let yourself continue, you’ll probably cause more problems and damage than you’ll solve or fix. Take a break

HARlEY DAVIDSON AUTOMATIC PRIMARY CHAIN TENSIONER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to the appropriate Service Manual and remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect negative (-) battery cable. 3. Refer to the appropriate Service Manual and remove primary cover. 3 1 2 5 4 is00561 1. Screw (2) 2. Anchor plate 3. Nut and washer 4. Manual tensioner 5. Screw (2) Figure 1. Manual Tensioner: 1985-2000 Models 4. For 1985-2000 model motorcycles, remove manual tensioner and replace the carriage bolt as follows: a. See Figure 1. Remove two screws (5) and nut and washer (3), and remove chain tensioner (4). b. Remove two screws (1) and anchor plate (2). c. Replace the carriage bolt in the anchor plate with the carriage bolt from the kit. d. Apply 2-3 drops of Loctite 262 (red) to the threads of the anchor plate mounting screws (1), then install anchor plate and two screws. Tighten screws to 12- 14 ft-lbs (16-19 Nm) . For 2001 and later model motorcycles, remove manual tensioner as follows: a. See Figure 2. Remove nut and washer (1) and remove chain tensioner (2) Removing the Autotensioner for Service 1. Use a tie wrap and secure the shoe to the base of the autotensioner, without securing it to the autotensioner bracket. This will retain the autotensioner adjustment for reinstallation during service. 2. Remove two autotensioner hex screws, and autotensioner. Resetting the Autotensioner 1. See Figure 5. Compress autotensioner wedge (1) and spring back to the base. 2. Hold wedge in position by inserting a hex wrench or pick tool through the hole in the base of the autotensioner. 3. See Figure 6. Move plastic autotensioner shoe (1) into place as shown. 4. If available, install shipping plate (2) to secure the shoe to the base. If it is not available, secure the shoe to the base with a tie wrap

BMW K1100LT/ RS Repair Manual

0

Filed Under (BMW) by admin on 03-12-2010

download
00.3 00 Tightening torque Model K 1100 LT K 1100 RS Connection Nm 11 Engine Freewheel Cover plate/freewheel cage at countershaft gear 10 Oil – water pump Oil pressure switch 40 Temperature sensor/screw plug 9 Pressure relief valve 40 Impeller 33 Pump housing to crankcase 10 Cover to pump housing 10 (3-Bond 1209) Intermediate flange Thrust plate at intermediate flange 9 (Loctite 243) Intermediate flange at crankcase 9 Crankshaft Pinion/rotor flange at crankshaft 50 Main bearing cap to crankcase 50 Connecting rod Big end cap Wrench angle 80 ° 30 Input shaft Front bearing 18 Rear bearing 40 Engine block Crankshaft cover 9 Lower part, outer 10 Oil sump 10 Oil filter cover 10 Oil drain plug 30 Cylinder head Cylinder head bolts (SI 11 062 95 (697) Short thread (from 6/93 to 11/94): Wrench angle, 1st stage Wrench angle, 2nd stage Long thread (since 12/94): Wrench angle, 1st stage Wrench angle, 2nd stage 64° 42° 75° 75° 22 20 Cylinder head cover 9 Camshaft Bearing cap 9 (Apply a thin coat of 3-Bond 1209 only at corners and butt edges) Chain sprockets 54 00.4 Timing chain Chain tensioner 9 Slide rail at camshaft bearing cap 9 Timing case cover Timing case cover 10 (3-Bond 1209) Cover for Hall-effect signal transmitter 9 Screw plug 40 Clutch Clutch housing to output shaft Tighten to Release and re-tighten to Wrench angle 50° 140 50 Housing cover 19 Alternator Alternator to intermediate flange 22 Driver 33 Starter motor Starter motor to gearbox 9 Mixture preparation Intake stub pipe 9 Fuel injection rail 9 Cooling system Coolant stub pipe at cylinder head 9 Temperature sensor at coolant stub pipe 30 Air cleaner Lower part of air cleaner housing 21 12 Engine electrical system Starter to transmission 9 Positive lead to starter 5 Alternator to intermediate flange 22 Clutch housing 50 Base plate 3,5 Setting ring 2,5 Hall generator cover 9 Ignition coils to intermediate flange 5 Spark plug 20 Model K 1100 LT K 1100 RS Connection Nm 00.5 13 Fuel preparation and control Injection rail 9 Intake stub pipe 9 Lower section of air cleaner housing 21 Intake air line 9 Motronic control unit 5 17 Radiator Connecting screw, temperature sensor 9 Fastening, thermostat cover 3 Radiator to frame 9 Coolant stub pipe to cylinder head 9 (with Loctite 243) Temperature sensor to coolant stub pipe 30 18 Exhaust System Exhaust system to cylinder head 21 Front silencer (muffler) 12 Exhaust system holder to footrest plate 33 Exhaust system to holder/footrest plate 9 Retaining bracket to gearbox 41 Oxygen sensor Hand-tight 21 Clutch Clutch housing to output shaft tighten to loosen and retighten to tightening angle 50° 140 50 Housing cover

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

BMW F 650 CS Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Connection 11 Engine Freewheel housing and freewheel Nm 35 (clean thread + Loctite648) Engine block Nm 10 Double drive gear on crankshaft Nm 180 (clean thread + Loctite243) Driver to countershaft Nm 140 (clean thread + Loctite243) Pressure plate Nm 10 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Chainwheel to main shaft Nm 140 (clean thread + Loctite243) Signal transmitter Nm 8 Ignition cover Nm 10 Cylinder base Nm 10 Fastener for chain tensioner Nm 40 Oil circuit Oil filter cover Nm 10 Oil pressure switch Nm 12 (clean thread + Loctite243) Strainer cover to housing half Nm 8 Drain plug, on-frame oil tank Nm 21 Engine oil drain plug Nm 40 Oil supply/oil return lines to engine Nm 42 Oil pump cover Nm 6 (clean thread + Loctite243) Oil pressure valve Nm 24 Oil retaining valve Nm 24 Cylinder head Collar nuts for cylinder head Nm 60 Collar screws for cylinder head Nm 33 Machine screws (chaincase) Nm 10 Camshaft bearing cap Nm 10 Chain sprockets to camshafts Nm 60 threads oiled Chain guide to camshaft bearing cap Nm 10 (clean thread + Loctite243)
00.4 Cylinder head cover Nm 10 Machine screw (hole for locating screw) Nm 25 Model F 650 CS Connection 12 Engine electrics Spark plug Nm 20 Magnetic hub to crankshaft Nm 180 (clean thread + Loctite243) Signal transmitter Nm 8 Engine block cover, left/right Nm 10 Starter to clutch cover Nm 10 Positive lead to starter motor Nm 9 Positive contact to starter motor Nm 4 Necked-down bolt, starter housing Nm 6 Cable cover to engine block Nm 9 Cable holder to ignition cover Nm 8 Stator to ignition cover Nm 10 (clean thread + Loctite243) Ignition coil bracket to cylinder head cover Nm 9

Incoming search terms:

YAMAHA YZF-R1 engine TechnicaL Specification

0

Filed Under (Yamaha) by admin on 13-11-2010

download
The 2006 model runs with the same 998 cc liquid-cooled 4-stroke DOHC 4-cylinder 5-valve layout featuring a 77 x 53.6 mm bore and stroke and 12.4:1 compression ratio. Equipped with a 3-axis transmission, fuel injection and 40 degree forward slanted cylinders, this ultra-compact powerplant is one of the most highly respected supersport engines of all time. Yamaha’s engineers have conducted a thorough examination of the R1′s intake and exhaust efficiency, and for 2006 a range of detailed changes in this area have achieved a 3 Hp increase in power at 12,500 rpm without direct air induction. One of the most significant changes is the use of shorter intake valve guides for 2006. Measuring 27.5 mm, these new guides are 5 mm shorter than the 2005 model, and this 15% reduction in length increases engine efficiency by increasing intake air flow, and reducing frictional power losses. To match the new intake valve guides, the 2006 model also features smoother intake ports. Furthermore, the clutch boss has been modified to increase the oil flow to the clutch assembly. other detail changes The design of the compact cam chain tensioner has been revised, and now features a different sealing system for improved durability. The overall length of the main gear axle is increased by 5 mm, and the engine cover is modified accordingly. engine TechnicaL highLighTS n 998 cc liquid-cooled 4-stroke DOHC 4-cylinder 5-valve n 3 hp power increase to 175 Hp @ 12,500 rpm* n 40 degree forward incline cylinder n Fuel injection n Ultra compact 3-axis transmission n 77 x 53.6 mm bore and stroke n 12.4:1 compression ratio n New smoother intake port design n New shorter intake valve guides n Higher intake and exhaust efficiency n Modified cam chain tensioner n Redesigned clutch boss * Without direct air induction
chaSSiS The R1′s Deltabox V chassis has been developed with the benefit of ongoing structural analysis and repeated testing, all the time using input from our highly successful MotoGp race programme. For 2006 the R1′s class-leading aluminium Deltabox V frame remains externally similar to the existing model, but beneath the skin some subtle yet significant changes have taken place

Kawasaki KFX KLX 400 Camshafts Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove the plug bolt from the back of the cam chain tensioner assembly. It is under pressure from the spring. Remove the spring and pin. Remove the bolts and tensioner assembly from the cylinder. Release the lock on the tensioner assembly and push the tensioner rod into the assembly so that it is fully retracted. Remove the eight 5mm Allen headed bolts that hold the cam caps in place. Remove the cam caps; be aware of the locating dowels in the caps to keep them from falling into the engine. It may be necessary to pry very lightly on the caps to lift them off their dowel pins. Do not use the cam lobe as the pry point. Lift the intake camshaft out of its pocket in the cylinder head casting. Remove the cam chain from the sprocket, set the stock camshaft aside. Lift the exhaust cam out of its pocket in the cylinder head casting and remove the chain from the sprocket. Do not drop the cam chain; dangle it over the side of the engine while keeping slight upward pressure on the chain to maintain its position on the drive sprocket on the crankshaft. Using assembly lube, lube the shim buckets and bearing surfaces for the camshafts in the cylinder head. Set the exhaust camshaft into the cylinder head casting while at the same time fitting the cam chain over the sprocket. Make sure that you keep all the cam chain slack to the back of the engine. Repeat the above process for the intake camshaft. Again, make sure you keep the chain slack to the cam chain tensioner side of the engine. Check to be sure the crankshaft is still at TDC. Check the location of the cam lobes. The camshafts are marked, and preset to 108-degree centers. If the lobes are not where they should be, adjust the positioning of the camshaft by rotating the sprocket one tooth on the chain. Do this until it is in the correct position as before you removed the camshafts. Check the positioning of the crankshaft for the TDC mark

Incoming search terms:

Incoming search terms: