Yamaha V-Star 1100 Jetting the Carburetors INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-03-2012

download
Remove air filter housing Remove the seat or seats Disconnect Fuel Lines (also the vapor line from tank to charcoal canister on California models) Disconnect instrument connectors from the fuel tank Remove fuel tank Remove air box Disconnect TPS and heater connectors Remove chrome carb cover Disconnect Fuel Lines Remove rubber carb elbows Disconnect throttle cables from carbs Remove the carbs Perform the jetting 1. Remove the Chrome air filter housing. To remove the chrome dog-dish (air filter housing) from the right side of the bike, you will need to remove the two mounting bolts and loosen the clamp that holds the air duct to the back of the housing. You will need a 5 mm Allen wrench and a #2 Philips screwdriver. 2. Remove the seats. This can be accomplished by using a 5 mm Allen wrench and removing the Allen head bolt from just behind the rear seat and the bolt just behind the front seat. Pulling up and back will free the seats. One smooth motion will do it. 3. Gain access to the dashboard plug and unplug it (It is white) Note: Your trip odometer will lose its count, please record the number if you wish to save your current mileage for this tank of gas. Figure A shows the three plastic rivets that need to be removed to gain access to the dashboard plug. Using your Philips head screwdriver, press the small circle in the middle of the rivets down… a click is felt. Remove the rivets by hand. You have freed the cover and you may lift it up to expose the electrical connector that needs to be unplugged. Figure B shows the plug

Incoming search terms:

KTM Superduke 990 MotoHooligan Airbox Installation

0

Filed Under (KTM) by admin on 26-01-2012

download
Undo the screws retaining the left and right front tank spoilers and remove. Fitment of Motohooligan airbox is possible without removing the tank but task is much easier if this is done. Access for removal of SAS system and installation of PC111 is also much improved and it’s worth the additional 5 minutes work. It would also be a good idea to do this with an empty tank so it’s lighter to handle. Unscrew front retaining bolt from front of tank and lift tank to access the spring damper on the left hand side. On standard Superdukes release the two circlips, carefully support tank and remove damper unit. (NB. SDR model not fitted with damper). Lower tank back into position and unscrew one of the pivot bolts at rear of tank Stage 1 – remove spoilers and tank Note : Fuel line has a connector half way between tank and airbox. but leave it in position to support the tank whilst you unscrew the other side. Once both bolts are unscrewed tank is free but still attached by fuel lines and electrics. Lift the rear of the tank to expose the two electrical plugs and disconnect both making sure that the retaining pins are pushed in first before you pull them apart. Reaching underneath the rear of the tank you’ll see the fuel line running into the base of the airbox. Half way down there is a connector with a metal button. Press this and pull the fuel line apart – you might want to have a rag handy to catch any fuel drips. Pull off the breather tube at the front, (on US models also pull off the breather that leads to the charcoal canister in the tail), and lift the tank away

Incoming search terms:

Honda VTX 1300 Motorcycles All Models Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black f. Install supplied Canister/Regulator bracket with supplied hardware. Figure 3. Make sure the hoses/electrical wires are routed underneath the bracket as shown. Figure 4 Qty Description 2 3/8-24×1-3/4 hex head bolt 4 3/8 SAE flat washers 2 3/8-24 Nyloc nuts g. Install Canister and Regulator with supplied hardware. Figure 4 Qty Description 4 ¼-20×1-1/4 hex head bolt 8 ¼ SAE flat washers 4 1/4-20 Nyloc nuts

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

Incoming search terms:

Incoming search terms: