CYCLE SOUNDS T-TAP POWER HARNESS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-04-2012

download
This t-tap plug is designed to work with Cycle Sounds audio systems. However it can be used to wire many add on 12 volt accessories to you Harley Davidson motorcycle. This plug is rated for 6-8 amps of power and should not be used for adding any product that is rated for more than the t-tap plug is rated for. Take the time to check the products power rating for which you want to install to make sure it is compatible with the t-taps amperage rating. Failure to do so couldlead to electrical failures, which could result in serious injuries or even death. it is possible to overload your motorcycles charging system by adding too many electrical accessories. U se amp meter to verify all power connections. Also check product power ratings for anything you are trying to install. Exceeding the maximum amperage can lead to electrical failures, which could result in serious injuries or even death. INSTRUCTIONS: Step 1: remove seat on bike and locate the wire harness under the seat that matches the plugs on the t-tap harness (2120-0026.) Location may vary between bike models. Step 2: unplug bike harness and snap each end of t-tap harness in correct plug opening. When finished connect power wires to the male plug.(all Cycle Sounds audio systems come pre wired with correct wire colors and terminals). When using this t-tap for any other 12 volt accessory, make sure the red and black wires are snapped into their proper pin connectors. Kit does not come with power terminals for the accessories device. See your local bike dealer for purchase of terminals

SUZUKI SV1000 ELECTRICAL SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COUPLER •With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. (C” -78-14) • * Bend the clamp properly so that the wire harness is clamped securely . • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . ELECTRICAL SYSTEM 7- 3 7-4 ELECTRICAL SYSTEM BATTERY •The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. • Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE HARNESS ROUTING” section. (CJ8-14)

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.

Incoming search terms:

BILLET ALUMINUM DISTRIBUTOR WITH ELECTRONIC ADVANCE AND ADJUSTABLE REV LIMITER FOR 1936-69 HARLEY BIG TWIN MOTORCYCLES INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ELECTRICAL SYSTEM A 12 volt electrical system is required. Check that the charging system is working properly and not producing over 16 volts. DISTRIBUTOR CLAMP A 1966-69 style distributor clamp (original or aftermarket) is required. MODULE This distributor uses an Accel Single/Dual Fire Ignition module part number 35496. See the enclosed form “Instruction Sheet Single/Dual Fire” for instructions on wiring, adjusting the rev limiter and selecting an advance curve. COIL(S) A coil(s) with a total primary resistance of 2 to 4 ohms is recommended. INSTALLATION Step 1 Turn the ignition switch to the off position. Rotate the engine until it is on the compression stroke for the front cylinder. Continue to rotate the engine until the TDC mark is visible through the timing hole. (see repair manual if necessary). Step 2 Remove the existing distributor if still in the engine. Step 3 Remove the two button head screws from the top of the Mallory distributor. Pull the top cover off the distributor. Remove the two hex standoffs and pull the module and upper housing off the distributor base assembly. Adjust the switches on the module for the desired advance curve and rev limit. FORM 1627 07/08 Step 4 Install the distributor base assembly in the engine with the screw holes and shutter wheel positioned as shown in Figures 1 and 2. It may be necessary to pull the distributor out, turn the shaft and reinstall to get the shutter wheel at the approximate angle shown. The slots should be at about the11 o’clock and 7 o’clock positions. The screw holes should be at the 9 o’clock and 3 o’clock positions. Step 5 Install the distributor clamp and tighten the clamp bolt lightly so the distributor can still be rotated. Step 6 Set the upper housing on the base assembly as shown in figure 3. (The upper housing will only install one way because of the locating screw) Rotate the base assembly slightly if necessary so that the slot in the shutter wheel lines up with the slot in the upper housing. Tighten the distributor clamp

Incoming search terms:

EVO 3-Phase Charging System Installation And Owner's Manual

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
install rotor onto sprocket shaft and seat against rotor spacer 9. Install the compensator extension shaft on the sprocket shaft 10. Using your motorcycle’s specific repair manual instructions, check for proper chain alignment. Use OEM-specified shims to bring chain alignment into specification if required. 11. Using your motorcycle’s specific repair manual instructions, install the primary drive and clutch. Assure that all driveline components line up correctly. 12. Apply Loctite Threadlocker #262 (“red”) to the threads of the sprocket nut (also supplied with compensator shaft extension kit). Tighten sprocket nut to 150-165 ft-lbs (203.4-223.7 Nm). 13. Using your motorcycle’s specific repair manual instructions, install the primary cover. 14. Connect the negative battery cable. 2.3 Factory Regulator Removal 1. Disconnect the negative battery cable. 2. Using your motorcycle’s specific repair manual instructions, remove the regulator. Save the factory-supplied hardware. 2.4 3-Phase Regulator Installation 1. Connect the 3-pin stator connector to the regulator. 2. Using the factory-supplied hardware, locate the 3-phase regulator on the mounting bracket and install using the factory-supplied hardware. Tighten to 50-80 in-lbs. 3. Attach the ground wire between the bracket mounting bolt and the bracket. Tighten to 70-100 in-lbs. 4. Trial-fit the long power wire to the motorcycle, and route to the original location of the factory regulator wire on the circuit breaker. 5. Trim any excess wire, and strip 5/16″ of insulation from the end of the wire using a wire stripper. 6. Slip the 1″ length of heat shrink (supplied) onto the wire. 7. Crimp on the (supplied) ring lug to the end of the wire, taking care that a good crimp connection is made.

2003 Model Ural Gear Up, Patrol, Tourist Owners Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
19 Kick lever Is designed to start the engine. On pressing the lever the crankshaft of the engine is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift foot pedal Is a two-arm type. When the front arm is depressed, shifting from higher to lower gear takes place. When the rear arm is depressed, shifting from lower to higher gear takes place. Since the heel-toe shift lever is short-coupled, you will find it easier to shift into a higher gear if you do not use your heel to shift, rather the ball of your foot. The neutral position is fixed between the 1st and 2nd gears. It is important to shift smoothly with a constant force and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pushed. IMPORTANT! The green pilot lamp will illuminate when either the transmission is in neutral or when the reverse gear is engaged (see “Starting the Engine”). Turn indicator pilot lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral and reverse gear engagement , indicates that the gearbox is either in neutral or in reverse. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers not miles.

Incoming search terms:

2007 Ural Retro Model Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed urn indicator lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral lamp indicates that the gearbox is in neutral. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers