2009 Honda CRF450R Decompression Plunger PRODUCT UPDATE CAMPAIGN

0

Filed Under (Honda) by admin on 21-04-2011

download
JH2PE053*9K700001 thru JH2PE053*9K703372 (*) Denotes check digit UPDATE PROCEDURE DEALER VENTORY Any affected unit in your inventory must be updated with a new decompression plunger and weight before delivery to the customer. Refer tothe PARTS INFORMATION and the UPDATE PROCEDURE sections of thisb Service Bulletin. Refer to the 2009 CRF450R Service Manual for specific removal instructions. 1. Remove the seat (page 3-3). 2. Remove the shrouds (page 3-4). 3. Properly hang the fuel tank (page 4-6). 4. Remove the camshaft (page 9-10) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your Honda. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your Honda, or that your Honda has the condition described. To determine whether this information applies, contact an authorized Honda dealer. 5. Replace the decompression weight and plunger with kit parts (page 9-14). 6. Reinstall all previously removed parts. IDENTIFICATION When you have completed the update, place a punch mark before the first digit of the V.I.N. located on the right side of the steering head. 0080 WARRANTY INFORMATION This Product Update Campaign ends on arch 7, 2012. Normal claim submission requirements apply. fter completing the UPDATE PROCEDURE,submit one warranty claim per unit with the following information: WARRANTY CLAIM TEMPLATE: Template: R02A* Flat Rate Time: 1.2 hours *Template reads “R-zero-2-A”.

Incoming search terms:

2006 Honda GL1800 AirbagCB Radio Squeal REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 08-04-2011

download
To remedy this problem, a ferrite core harness kit is now available for installation. 2006 GL1800 VIIIA (Airbagmodels) with optional CBRadio. Install a ferrite harness core kit according to the installation instructions that are packaged with the kit. ÒÑÌÛæ • The kit includes both a rider and a passenger harness; it’s necessary to install both harnesses to eliminate the squealing noise. • Passengers must route the headset cord as shown. If routed otherwise, it will be too close to the motorcycle’s antenna, which can create an interference. Subharness installation can be confirmed by removing the left-side fairing pocket, and check- ingtoseeifthe harness is already installed. Ferrite CoreHarness Kit (1 required) P/N: 08E95-MCA-100WA H/C: 8607665 ÒÑÌÛæCallTechLineat (800) 421-1900 to order parts. Due to the limited number of affected units and parts availability, ordering will be controlled until May 31,2007. Normal warranty claim submission require- mentsapply. Submit one claim per VIN. Template: GL19 Flat RateTime: 0.3 hours

2001-2002 GL1800 A ABS Speed Sensor Wire Clamp Location INSPECTION/ REPAIR PROCEDURES

0

Filed Under (Honda) by admin on 29-01-2011

download
1. If the VIN is within the preceeding range, inspect the front ABS speed sensor wire clamp according to the following illustrations. 2001-2002 GL1800A ABS Speed Sensor Wire Clamp Location INCORRECT Installation CORRECT Installation Service Bulletin American Honda Motor Co., Inc. 2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location 0112 GL1800 #9*GL1800 #9*0112*2001-2002 GL1800 ABS Speed Sensor Wire Clamp Location*GL1800, ABS Speed Sensor Wire Clamp Location*Motorcycle*1800 2 of 2 ©2001 American Honda Motor Co., Inc. – All Rights Reserved GL1800 #9 DECEMBER 2001 IDENTIFICATION There is no identification mark associated with this Service Bulletin. PARTS INFORMATION There is no parts information associated with this Service Bulletin. WARRANTY INFORMATION The normal warranty claim submission requirements apply. Submit one warranty claim per VIN with the following information only: Inspected and REPAIRED Template: GL#9 Hours: 0.2 hours Parts: None If the clamp is installed correctly on top of the speed sensor, no further action is necessary. 3. If the clamp is installed incorrectly under the speed sensor, remove and reinstall the clamp and speed sensor correctly. Torque the bolts,. Torque: 12 N • m (1.2 kgf • m, 9 lbf • ft) If the speed sensor wire clamp for the front ABS speed sensor is installed incorrectly, the ABS speed sensor air gap may be out of specification. This does not affect ABS speed sensor operation, but the clamp should be installed correctly. Inspect and repair all affected units using the Inspection/Repair procedures listed below. Inspect all unsold units and customer units brought in for service. AFFECTED UNITS 2001-2002 GL1800A units as follows: MODEL 2001 GL1800A All units 2002 GL1800A 1HFSC474*2A100001 – 1HFSC474*2A101643 * = denotes check digit Any unit in the above VIN range may be affected and should be inspected according to the procedures in this Service Bulletin. All units outside of the above VIN range do not require inspection. CUSTOMER NOTIFICATION There is no customer notification associated with this Service Bulletin.

Incoming search terms:

Incoming search terms: