ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

YAMAHA WR450F (S) 2-TRAC SPECIFICATIONS/ SUPPLEMENTARY OWNER’S SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING DIAGRAM STEERING DAMPER ADJUSTMENT 19 Damping sweep controls Damping sweep ontrols 5 are located on each side off the damper body. Damping is in position 2, (12 o´clock), when delivered from Yamaha. This setting is fitted for enduro, motocross and off-road riding. WARNING Always ensure that valve setting is within the permitted ranges. NOTE: Both damping sweep controls must always be set in identical positions. Always use positions according to the clock. Suitable starting position: Motocross pos. 1 or 2 Enduro pos. 2 or 3 Off-Road pos. 2, 3 or 4 Technical data External measures 70x70x35 mm Seals Low friction type Oil Öhlins part no. 01306-01 Maintenance and inspection The steering damper is a precision instrument, with extremely fine tolerances. It is therefore essential that it is maintained in a correct manner. Maintenance and service should be carried out by an authorised service center. NOTE: After washing the motorcycle wipe clean and spray with all-round oil. Never subject to direct high-pressure cleaning since water may otherwise penetrate the damper. Ensure that there is no leakage of fluid and that there is no visible damage to the housing and mounts FRONT FORK REBOUND DAMPING FORCE ADJUSTMENT The rebound adjuster is located at the top of the fork leg. 1. Adjust: • Rebound damping force By turning the adjuster. Stiffer → Increase the rebound damping force. (Turn the adjuster in.) Softer → Decrease the rebound damping force. (Turn the adjuster out.) Extent of adjustment: Maximum Minimum Fully turned in 20 clicks out position (from maximum position) • STANDARD POSITION This is the position which is back by the specific number of clicks from the fully turned-in position. Standard position: 14 clicks out Do not force the adjuster past the minimum  or maximum extent of adjustment. The adjuster may be damaged. WARNING Always adjust each front fork to the same set- ting. Uneven adjustment can cause poor handling and loss of stability

Incoming search terms:

PASSENGER FLOORBOARD RELOCATION ARMS FOR TRIUMPH AMERICA AND SPEEDMASTER

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. If you are installing the relocation arms at the same time as floorboards install the floorboards first per their instructions. When installing the relocation arms with floorboards already installed proceed as follows. 2. Starting on the left side, fold the floorboard up. Remove the socket head bolt and nut which secures the floorboard to the motorcycles stock peg support and remove the floorboard taking notice of which holes the dowel pins are located in. 3. Install one of the 5/16″x1 Ω” hex bolts supplied thru the stock peg support from the backside (The threads of the bolt will face out towards you.) Place the two dowel pins into the holes at one o’clock and seven o’clock on the stock peg mount. Place the spacer blocks backside (stamped with an “L”) onto the bolt and align the hole with the pins. 4. Locate the relocation arm that has an “L” stamped on the backside of it. Place two of the supplied dowel pins into one of the two sets of the holes in the arm that are directly across from one another (180 degrees apart). Place the arm onto the spacer bock aligning the pins in the arm with the holes closest to six and twelve o’clock. Depending on which of the two sets of holes on the arm you chose the arm would, either be down at about seven o’clock or just below nine o’clock. These are the initial height settings and you may select which ever set is most comfortable for the passenger. Install one of the acorn nuts supplied onto the bolt and make finger tight. 5. Place the floorboard with its two dowel pins into the set of holes at the other end of the relocation arm that allows the floorboard to be horizontal or parallel to the ground. Use one of the 5/16″x3/4″ socket head bolts supplied to bolt the floorboard to the relocation arm and make finger tight. 6. Install the right side in the same manner, place the dowel pins in the holes at eleven o’clock and at five o’clock on the stock peg mount, then the spacer blocks backside (stamped “R”) onto the pins followed by the relocation arm with two dowel pins in one set of holes (180 degrees apart). Check to see that the right arm is at the same height or position as the left then install the acorn nut finger tight. Bolt the floorboard the other end of the arm using the remaining dowel pins and socket head bolt. Tighten the two bolts with the acorn nuts and the two socket head bolts securely

TRIUMPH AMERICA AND SPEEDMASTER PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 12mm nuts located behind the stock foot peg assemblies and remove the peg sets. 2. Starting on the left side locate the left floorboard assembly and left round chrome spacer block. These will be stamped with an” L” on the back side. Insert two of the 3/16″ x 1/2″ dowel pins supplied into the two holes where the foot peg was mounted at one o’clock and seven o’clock. Place the spacer blocks backside (stamped with the L) onto the pins 3. Place two more of the dowel pins in the holes on the outside of the block using the holes at twelve o’clock and six o’clock. Place the left floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. 4. On the right side install two more of the dowel pins supplied into holes where the foot peg was mounted at eleven o’clock and five o’clock. Place the remaining spacers backside (stamped with an R) onto the pins 5. Place the remaining two dowel pins supplied into the holes of the spacer block at six o’clock and twelve o’clock. Place the right floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. NOTE; if you are also installing the TA005-5 relocation arms, follow those instructions next. Finally be sure to tighten all bolts securely

Incoming search terms: