Filed Under (KTM) by admin on 03-02-2012

Clutch lever 500133-10 The clutch lever  is fitted on the left side of the handlebar. The clutch is hydraulically operated and self-adjusting. Hand brake lever 400196-10 Hand brake lever  is located on the right side of the handlebar. The hand brake lever is used to activate the front brake. EmergencyOFFswitch 500144-10 The emergency OFF switch  is fitted on the left side of the handlebar. Possible states Ignition off-In this position, the ignition circuit is interrupted, a run- ningenginestops, and anon-running engine will not start. Ignition on-In this position, the ignition circuit is closed, and the engine can be started. Ignition switch 300396-10 The ignition switch  is on the right behind the headlight mask. Possible states Ignition off-In this position, the ignition circuit is interrupted, a run- ningenginestops, and anon-running engine will not start. Ignition on-In this position, the ignition circuit is closed, and the engine can be started. Electrics tarter button 500144-12 Electric starter button  is fitted on the right side of the handlebar. Possible states •Electric starter button is in home position •Electric starter button is pressed-In this position, the electric starter is actu



Filed Under (KTM) by admin on 25-01-2012

Using a small phillips head screwdriver, loosen the locking screw ( B ) on the kill switch ( C ). Remove any cable ties and unplug kill switch from existing wiring. Step 2 Loosen clutch cable perch ( D ) and move inboard about 1/2 inch. Important Note Regarding Magura Brakes The KTM uses the Magura hydraulic brake, which may cause potential interference between the turn switch and the lever adjuster. Make sure you have enough clearance between the parts. You can either move the grip out slightly, or take a file and sand away a small notch in the turn switch where it may rub. Install Turn Switch Step 1 Open and wrap the new turn switch ( E ) around handlebar and securely fasten with two screws ( F ) as shown. Make sure you have clearance between the grip, the switch and the lever! Step 2 Route turn switch wiring down and along handle bar behind Dakar headlight unit and in through frame cable guide. Secure switch wiring to handlebars with one cable tie. For more information, please refer to the Cable Routing Diagram

KTM EXC taillights Installation manual


Filed Under (KTM) by admin on 23-01-2012

Step1: Remove headlight, (headlight switch) seat and gas tank from KTM. Step 2: Partially install the headlight assembly using the top right band only to hold it in place temporarily. You will need to plug wires to this assembly and if you put all four bands on you will not be able to make the connections. Step 3: Install handlebar switch on clutch side. You will need to move clutch perch to the right (about ½ inch to1 inch) to make room for the switch. The red knob on the clutch adjuster should just miss the handlebar switch. The switch plugs into the circuit board on the bottom of the headlight using the 8-pin plug (the only unused 8-pin one on the circuit board) Step 4: Behind the gas tank and in front of the air box is a small rectangular hole in the frame. You will be feeding two lines with the plug ends first down through this hole. They must be fed one line at a time and you may need to use needle nose pliers to grab them and help pull them through. The lines you want to feed through this hole are the power line with two-pin molex plug and the line for the taillight with the six-pin plug. Route these wires all the way to the headlight assembly along the left side of the bike on the bottom of the gas tank frame tube. In this step we will connect the power line only. With the handlebars turned all the way to the right, plug the power wire into the back of the headlight assembly making sure to leave some extra wire so you can turn the handlebars both ways without tugging on the wires. The other end of the power line has battery terminal loops. The positive has an in-line fuse and the other black wire is the negative. Connect these to the battery.



Filed Under (Honda) by admin on 14-11-2011

1500 91255-169-003 30-42-11 FRONT FORK SEAL (S/S) (SLEEK) Improved Quality 200 20 PCS
1500A ————— SET OF 2 PCS FRONT FORK DUST SEAL (S/S) 100 10 PCS 1501 90756-198-000 7-37-7.5 FRONT FORK TRIPLE (COLLER) (CD-100) 200 20 PCS 1502 91202-302-01013.8-24-5 KICK SHAFT 200m20 PCS 1502A 91202-302-010m13.8-24-5+1514 KICK SEAL(SPL.GRADE O.E TYPE) MATERIAL WITH PUCH ROD RUBBER 100 10 PCS 1503 91205-350-000 6-25-6 CLUTCH 200 20 PCS 1504 91202-GK4-722 18.9-30-5 MAGNET

Incoming search terms:

HONDA VFR800, CBR1100XX Blackbird, ST 1300 Sport Brake Lever Part INSTALLATION


Filed Under (Honda) by admin on 02-11-2011

Congratulations on your purchase of an ASV C/5 Sport Streetbike lever. The correct installation of control
levers on a sport/street motorcycle is critical. Incorrect installation or the installation of an incorrect part
can result in a malfunction of your clutch and / or front brake system. This lever should be installed by a
certified mechanic; preferably at your local motorcycle dealer service dept. ASV Inventions, Inc. accepts no
liability for malfunctions as a result of incorrect installation or the installation of a part that was not
designed specifically for your motorcycle. Please check the list below to confirm that the correct year, make
and model of your motorcycle is listed. If the correct year, make and model of your motorcycle is not listed
below, then this part is not the correct part for your motorcycle and must not be installed onto your
motorcycle. ASV C/5 Sport front brake lever part number: BRC541 fits only the following motorcycles:
Please disregard any dashes or letters after this part number that are listed on the part number label of
this box that your lever came in, (ex; BRC541-SK) Any dashes or letters following your part number are for
colors and/or length of the lever and do not affect the application of the lever to the bike.



Filed Under (Toyota Manuals) by admin on 03-06-2011

This bellhousing is not compatible with transmissions that were previously equipped with diesel engines. The bellhousing design incorporates a special modified clutch release lever and a Toyota Land Cruiser slave cylinder. We have provided slave cylinder mounting on the passenger side of the bellhousing and have incorporated a new push rod location that will provide a quick short travel of the clutch release mechanism. The kit does not include the Toyota Land Cruiser slave cylinder, Part No. 31470-60022. The bellhousing is designed for the 153 tooth flywheel application. If your block is equipped with a 168 tooth flywheel, you will be required to use a high torque starter without a nose cone to fit the bellhousing (P/N 22-0001). The bellhousing is compatible with the Buick flywheel that has 160 teeth. A slight modification may be required in the starter pocket area when using the Buick installation.



Filed Under (Kawasaki) by admin on 27-04-2011

Front Axle and Outer Tube Front Wheel Axle Holder Rear Axle and Nut Handlebar Crown and Inner Tube Handlebar Crown and Steering Stem Steering ring nut (Upper and lower) Brake Caiiper (Front/Rear) Bleed Screw and Brake Caliper Brake Hose and Union Bolt Front Master Cylinder and Cylinder Cap Front Fender and Outer Tube Handlebar Boss and Front Fork Handlebar and Handlebar Boss Engine Mounting: Front ; Rear — Upper ; Rear — Lower 1 Down Tube and Frame: Front 1 Rear l Footrest Bracket and Frame I Pivot Axle and Nut Relay Arm and Frame Connecting Rod and Swingarm Connecting Rod and Relay Arm Rear Shock Absorber and Reiay Arm Rear Shock Absorber and Frame Footrest and Footrest Bracket I Rear Footrest Bracket and Frame Rear Master Cylinder and Rear Arm Bracket Cowling and Stay Compression Bar and Brake Caliper Bracket Front Fork Pinch Bolt: Upper Lower Sprocket and Clutch Hub Brake Disc and Clutch Hub Inner Tube and Steering Stem Frame and Rear Frame: Upper



Filed Under (Harley Davidson) by admin on 14-04-2011

This kit contains the following items: ITEMDESCRIPTION/ QUANTITY PART NO. 1 Stud, double ended, 5/16-18 (4) 3265A 2 Bushing (4) 67621-94 3 Acorn nut, keps, 5/16-18 (Chrome) (4) 7992 Installation 1. Using a T-40 TORX drive head, remove the upper left- side chrome button-head fork screw and chrome flat washer and discard. 2. See Figure 1. Obtain a double-ended stud (1) and chrome acorn nut (3) from the kit. Thread the nut onto the NON lock patch side of the stud and hand tighten. NOTE Position the clamp so the clutch cable is to the rear of the stud. 3. Slide the clutch cable clamp (4), along with the cable, into position on the stud as shown. Assemble a bushing (2) from the kit onto the stud threads. 4. Insert the lock patch side of the stud through the headlamp nacelle and into the upper fork bracket. Tighten the acorn nut and stud to 15-20 ft – lbs (20-27 Nm). 5. Continue, one at a time, replacing the three remaining chrome button-head fork screws and flat washers with the studs, bushings and chrome acorn nuts from the kit. Tighten to 15-20 ft – lbs (20-27 Nm)



Filed Under (Harley Davidson) by admin on 29-03-2011

INSTALLATION 1. Dyna Models: Remove the plastic clip that fastens the clutch cable to the frame downtube just below the clutch cable adjuster and boot. Leave the clip above the adjuster in place. Softail Models: Remove the plastic clip and screw that attaches the clutch cable to the frame downtube just above the clutch cable adjuster and boot. 2. ALL Models: See Figure 1. Cut the original rubber boot (B) from the clutch cable (A). Make sure that the clutch cable covering is not cut or damaged. 3. Obtain the two halves of the clutch cable adjuster cover (items 1 and 2) and two cushions (8). Peel the paper backing from one cushion (8), and center the cushion on the inside of one cover half. Repeat for the other cushion and cover half. 4. Obtain the two screws (7) from the kit. Position the cover halves on each side of the cable adjuster, and align the screw holes at each end. Place a drop of Loctite 243 – Blue on the screw threads, and fasten the cover halves with the two screws. Tighten to 21 in-lbs (2.4 Nm)



Filed Under (Harley Davidson) by admin on 21-03-2011

This kit is designed to fit 1980 – 1983 and 1988 and later FLHT and 1994 and later FLHR models without fairing low- ers. installation 1. Locate splash shield for left side. Bar and Shield should face forward and opening in splash shield should be on right side. 2. Slip splash shield on left side of engine guard. 3. An opening in the outer edge of the splash shield allows the splash shield to fit over highway footrests. 4. Place the wide attaching strap around the frame down- tube, do not put strap over clutch cable. 5. Slip buckles on attaching strap onto mating buckle halves attached to back side of splash shield. Latches will snap into locked position when buckle is properly closed. 6. Adjust the fit by lifting the Velcro®attached straps (on rear of splash shield) and changing length as required. 7. Repeat procedure for right side of vehicle. NOTE If splash shields cover amber reflectors mounted on frame down tubes, install reflectors included in kit as follows: 8. See Figure 1. Clean areas on both sides of fender (1) where amber reflectors are to be mounted. 9. Remove backing paper from rear of reflector and place reflectors in position (2). Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Low visibility of rider can result in death or serious injury. (00336a) NOTE To remove splash shields depress both latches with thumb and forefinger and gently pull buckle apart. Open remaining buckle and slide splash shield off engine guard