HARLEY-DAVIDSON 5 and 6 Speed OEM Transmissions ReverseGear User Operating Instructions

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
A. It is good practice to first engage first gear to stop the gearbox from spinning (This will prevent the “grinding” noise when reverse gear is engaged) and then place the bike in neutral and immediately engage reverse. If Reverse Gear still “grinds” after the above procedure – check the clutch adjustment to ensure the clutch is not dragging and causing the gearbox shafts to spin. B. Do not let the bike “free wheel” backwards while in reverse gear and the clutch engaged or disengaged (i.e. when rolling down a slope when in reverse) – The reverse gear will automatically try to disengage and will result in a “grinding” sound. To prevent this – Always stop immediately after the reverse action is completed. WARNING! Reverse gear is intended for light duty use only – like slowly backing in/out of parking spaces etc. Do not drive for long periods in reverse. WARNING! Do not attempt to engage reverse while the motorcycle is up on a lift stand. Maintenance Check transmission fluid levels regularly and fill with Manufacturer’s suggested lubricants. Warranty One year on reverse gear parts only. Champion will not warranty the Reverse Gear if it is deemed to be “abused” by the user like: – Engaging First Gear while the Reverse Gear is still engaged and/or – Over powering the Reverse Gear by revving and dropping the clutch and/or – For an Installation Error (not following the installation instructions exactly). Any attempt to modify this product without written permission from the manufacturer will void the warranty and may cause damage to vehicle and injury to persons.

Incoming search terms:

HARLEY-DAVIDSON 5 Speed Transmissions 1984 – 1999 EVO / 5 Speed & 1999 – 2006 Twin Cam Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
Remove Original Parts From Vehicle. 2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

BMW Motorcycles F 650 GS/Dakar Driveability Issues

0

Filed Under (BMW) by admin on 12-11-2010

download
Concern: Customer complains about hesitation, surging and stalling when the engine is operated at low to medium RPM. Service Measure: In the event of a customer complaint on the above concerns, please check the following points, adjusting to specification as necessary: Fuel pressure: Measure fuel pressure under all operating RPM. If fuel pressure is outside of specification, replace fuel filter with pressure regulator. Recheck fuel pressure, with new components installed, to confirm fuel pressure is to specification. Fuel pressure specification = 3.5+/- 0.2 bar Clutch adjustment: Clutch may not disengage completely with engine cold. Oil in the viscosity range 20W50 may be in use. Insure that the clutch is adjusted correctly and change oil to viscosity range 10W50. Control unit update: Using the BMWMoDiTeC CD 8/x, Update 3, update the programming of the BMS COMPACT control unit. The update of a BMS COMPACT control unit program is not to take place unless a customer has a complaint about hesitation, surging and stalling, these complaints have been verified by the retailer and the service measures covering fuel pressure, clutch adjustment and oil viscosity have been completed. Important Note: Always comply with the instructions, as included with the update CD, for the correct installation of CD 8/x, Update 3. Identification Label: Print a new identification label ( YELLOW for update ) and affix it to the BMS- COMPACT control unit. Please note that it is not permissible to deliver an updated motorcycle to a customer without the correct identification label affixed to the control unit.

Incoming search terms:

Harley Davidson Five Speed Transmissions Hydraulic Clutch Modification

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Hydraulic Clutch Modification for Harley Davidson With Champion Reverse Gear 1 1.1 Install Reverse Gear Assembly to gearbox. 1.2 Remove clutch cover (left side). 1.3 Remove Release Plate (clutch adjustment) and Push Rods. 1.4 Install Hydraulic Clutch Release Cover with supplied spacer and two gaskets. 1.5 Bleed clutch system. NOTE: When bleeding clutch system, lever feel will become hard, do not force lever because piston is at end of travel.(Continue Bleeding) 2 2.1 Install Push Rod. 2.2 Push the rod into clutch assembly to force hydraulic piston to its start position. Push the rod hard until the clutch cylinder is fully compressed. This is the start position. 2.3 Install Hydraulic Clutch Throw-Out Bearing Holder and bearing to push rod. Do not install circlip at this time. 2.4 If the throw-out bearing holder does not fully seat into the Pressure Plate (Figure 2.4), proceed to step 2.5. If shaft is too short then use throw-out bearing holder from Champion Reverse Gear Kit, skip next step and proceed to 3.0 2.5 Measure distance between bearing holder and pressure plate (ensure that push rod is pushed in) Figure 2.4 2.6 Remove bearing holder and push rod, reinstall bearing holder until seated (without push rod). Measure distance from pressure plate to bearing holder. Figure 2.6 2.7 Add measurements taken in steps 2.5 and 2.6 2.8 Add 0.090″ to total of step 2.7 (allowance for clutch plate wear). Measurement should be approximately 1/8″. 2.9 Measure push rod length. 2.10 Subtract measurement of step 2.8 from measurement of step 2.9 (push rod length). This measurement represents the amount of material to be removed from ball end of push rod. (Step 2.11)

Incoming search terms:

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Incoming search terms: