TOYOTA R150F, R151F ( AX15 ) 5 SP TRANS. TO CHEVY & BUICK ENGINE – TURBO CHARGED

0

Filed Under (Toyota Manuals) by admin on 03-06-2011

Download
This bellhousing is not compatible with transmissions that were previously equipped with diesel engines. The bellhousing design incorporates a special modified clutch release lever and a Toyota Land Cruiser slave cylinder. We have provided slave cylinder mounting on the passenger side of the bellhousing and have incorporated a new push rod location that will provide a quick short travel of the clutch release mechanism. The kit does not include the Toyota Land Cruiser slave cylinder, Part No. 31470-60022. The bellhousing is designed for the 153 tooth flywheel application. If your block is equipped with a 168 tooth flywheel, you will be required to use a high torque starter without a nose cone to fit the bellhousing (P/N 22-0001). The bellhousing is compatible with the Buick flywheel that has 160 teeth. A slight modification may be required in the starter pocket area when using the Buick installation.

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

Harley-Davidson Six Speed Transmissions FLH 2009 Up Champion Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
Preparation Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the clutch release cover (right side). 2.6 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.7 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.8 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Snap-On Part No: FWA62121 Snap-On Part No: FWA62121 Champion Part No: RG-100-100 Reverse Gear Installation Instructions Harley-Davidson Six Speed Transmission HD FLH 2009 Up Page 3 of 5 Revision 2 Boring Tool 3 Installation 3.1 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.2 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 1 3.3 Install the supplied (ear)plug into the main shaft hole. To be removed later. 3.4 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 2 3.5 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.6 Remove torque wrench from special tool. Do not remove special tool from small gear. 3.7 Using the supplied boring tool and the special tool as a guide, drill the main shaft through two holes of the special tool as shown. Stop when cutter contacts bearing race. Figure 3 3.8 Remove special tool, leaving main shaft plug in place, and thoroughly clean out the holes. Use care to ensure debris does not enter transmission. 3.9 Remove plug from main shaft hole. Figure 1 Figure 2 Figure 3 Note: To prevent gears from rotating during torque procedures, engage transmission into 1st gear and apply brakes Note: Frequently stop cutting and remove bit from hole to clean bit and vacuum debris from hole

Incoming search terms:

Harley-Davidson Six Speed Transmissions Reverse Gear Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the exhaust pipe support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.8 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.9 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Installation 3.1 Reinstall exhaust pipe support bracket with the supplied two 5/16-18 x 1 3/4″ long hex head bolts and the ¼” thick spacer between engine and bracket. Figure 1 3.2 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.3 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 2 3.4 Install the supplied plug into the main shaft hole. To be removed later. 3.5 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 3 3.6 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.7 Remove torque wrench from special tool. Do not remove special tool from small gear

HARLEY DAVIDSON REDUCED EFFORT CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
This kit fits all 2005 and earlier model motorcycles equipped with a Twin Cam 88® or Twin Cam 88B™ engine. INSTALLATION Replace Diaphram Spring NOTE Refer to the appropriate Service Manual for detailed information on the following generalized steps. 1. Remove the primary chaincase cover. 2. Partially disassemble the clutch pack in order to remove the diaphram spring. 3. Assemble the clutch pack using the diaphram spring from the kit. 4. Install the primary chaincase cover. Replace Inner and Outer Ramps NOTE Refer to the appropriate Service Manual for detailed information on the following generalized steps. 1. Remove and disassemble the transmission clutch release cover. 2. Clean and inspect transmission clutch release cover components. 3. Assemble and install the transmission clutch release cover, using the inner and outer ramps from the kit. SERVICE PARTS 1 2 3 is00464 Figure 1. Service Parts for Reduced Effort Clutch Kit Table 1. Service Parts Part Number Description (Quantity) Item 25605-00A Outer ramp 1 25604-00A Inner ramp 2 37882-06

HARLEY DAVIDSON HIGH PERFORMANCE CYLINDER STUD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit is designed for installation on 1986 and later XL model motorcycles. This kit is required on engines with compression ratios of 10:1 and higher. For XL 1200 engines with higher compression ratios, Screamin’ Eagle gasket kit part number 17046-98 is also recommended. Installation To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect the battery, negative cable first. 2. Remove top end heads and cylinders according to Service Manual instructions. Cylinder studs that are bent, scratched or broken must be replaced. Broken and bent studs distort clamp load, while scratches produce stress risers that may eventually lead to broken studs. Distorted clamp load causes head gasket leakage that may result in engine damage. Do not use a ratchet or breaker bar to install cylinder studs because they will bend the studs. 3. Remove existing cylinder studs according to Service Manual instructions. 4. Install new studs, Loctite end first. • Place a 0.313 inch DIAMETER BALL, HD Part Number 8860 (or from the XL clutch release mechanism) into the head bolt recess. Thread the stud into the head bolt until the stud bottoms on the ball. NOTE Pack clean shop towels into the crankcase openings to prevent the ball from falling into the flywheel compartment when removing the head bolt. • Clean the threads in the crankcase. • The studs have a Loctite patch on the crankcase end threads.Install the studs in the crankcase with the Loctite patch side down. • Use a T-handle to install the studs. Install studs until the free length is 4.84 ±.05 inches. See Service Manual for more detailed information. 5. Check all studs for proper height. 6. Reinstall the top end heads and cylinders according to the Service Manual Instructions