Rear Toyota Landcruiser 4×4 S-W 80-100 GX

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
Jack up rear of vehicle or raise on hoist. Support frame with safety stands. Remove lower shock absorber
attaching bolts. 2. Lower axle or raise body or vehicle until suspension is fully extended. CAUTION: Observe tension on brake line – do not strain. Remove coil springs noting location of the end of the coil spring in the lower spring seat. 3. Using a 3/4” drill enlarge the diameter of the hole in the lower spring seat to 3/4”. Remove all burrs and sharp edges (Figure 2). 4. Using a socket and extension, remove the rubber bump stop from the upper spring seat and discard (Figure 1). 5. Insert air cylinder into coil spring with stem at bottom (Figure 3). 6. Raise the axle or lower the body to install coil spring into spring seats and rotate to proper location. Attach lower shock absorber attaching bolts. Torque to 25 ft. lbs.

TOYOTA CELICA SPORT COIL SPRINGS (STREET)

0

Filed Under (Toyota Manuals) by admin on 06-06-2011

Download
Use a 13mm and 10mm socket or wrench to loosen and remove the bolts holding the brake lines to the strut. Retain the hardware for later re-installation. 4) Use a 21mm and 22mm socket or wrench to loosen and remove the two bolts holding the base of the strut to the spindle. Use a 12mm socket or wrench to loosen and remove the nuts retaining the top of the strut. The strut will now be free and can drop out of the vehicle. Use caution to avoid dropping the strut, as this could damage the strut or the vehicle. 5) Place one of the struts into the coil spring compressor and collapse the spring until the upper strut plate is no longer under tension. Remove the plastic dust cover on the top of the strut. Use a 19mm socket and a 6mm Allen wrench to remove the retaining nut at the top of the strut. Retain the hardware for later Re-installatio

2006 HONDA GOLD WING Specifications

0

Filed Under (Honda) by admin on 29-01-2011

download
Engine Type Liquid-cooled 4-stroke 12-valve SOHC flat-6 Displacement 1,832cm3 Bore x Stroke 74 x 71mm Compression Ratio 9.8 : 1 Max. Power Output 87kW/5,500min-1 (95/1/EC) Max. Torque 167Nm/4,000min-1 (95/1/EC) Idling Speed 700min-1 Oil Capacity 4.6 litres Fuel System Carburation PGM-FI electronic fuel injection with automatic choke Throttle Bore 40mm Aircleaner Viscous, cartridge-type paper filter Fuel Tank Capacity 25 litres (including 4-litre warning light reserve) Electrical System Ignition System Computer-controlled digital transistorised with electronic advance Ignition Timing 2° BTDC (idle) ~ 30° BTDC (3,500min-1) Sparkplug Type BKR6E011 (NGK); K20PR-U11 (ND) Starter Electric Battery Capacity 12V/18AH ACG Output 1,000W Headlights 12V, 55W x 2 (low) / 55W x 2 (high) Drivetrain Clutch Wet, multiplate with coil springs Clutch Operation Hydraulic Transmission Type 5-speed (including overdrive, plus electric reverse) Primary Reduction 1.591 (78/49) Gear Ratios 1 2.375 (38/16) 2 1.454 (32/22) 3 1.068 (31/29) 4 0.843 (27/32) 5 0.686 (24/35) Final Reduction 2.750 (33/12) Final Drive Enclosed shaf

Incoming search terms:

Kawasaki Mule 610 Without coil springs Installation

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1.)Begin by loosening the lug nuts on both front tires. Raise the unit, using a suitable lifting device or procedure, until the front tires are off the ground. If using a floor jack with stands, chock the rear wheels to prevent the unit from rolling. If using jack stands, make sure the stands are placed under the frame and not the body. Make sure the unit is stable and secure . 2.)Remove the tires / wheels. NOTE: Now is a good time to check the threads on the lug studs. Check for rust, pulled threads or other deterioration that could cause a stud/thread failure. 3.) The first thing to do is remove the front cowl and trunk on the bike. You can accomplish this by removing all the bolts (screws) around the perimeter of the cowl and removing some plastic “snap rivets”. To remove the rivets simply pull the center section up and then the rest will follow. 4.)Place a floor jack, or other suitable device, beneath the left side lower control arm. This is to prevent damage to the tie rod or slip yoke boot while disassembling the lower control arm and strut. Using a 14mm socket, remove the two retaining nuts and lock washers on the top of the struts. 5.)Leaning the strut forward toward the headlamp buckets will put the strut in position to allow you to reach over the top and place the strut spacer in place. Install the strut spacer on top of the coil retainer and tightening the nuts. Install the supplied gasket on top of the strut spacer, and re-install the strut assembly

Incoming search terms: