Motorcycle LED lights RENEGADE LIGHTS Installation Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Your new motorcycle LED lights are polarity sensitive–meaning that the RED wires on the LEDs must be hooked to the Positive (+) terminal and the BLACK wires must be hooked to the Ground (-) . All Red Wires must go to a common power wire and ALL Black Wires must go to a common ground. You cannot run the LED motorcycle lights in a series nor can you run the wires from one motorcycle LED light to another in a loop type installation. ( All of the wires on the motorcycle LED lights which you install will end up together in one place at your battery.) 4. Pick a hidden flat surface around the front of your seat area to mount the switch. ( You must be able to reach the switch when the seat and/or side covers are back on your bike.) You will install your switch later using the double-sided tape provided to you. 5. Next, begin choosing the locations where you would like to mount your motorcycle LED lights. Choose areas which will give you the most light coverage overall, but which will allow the motorcycle LED lights itself to be hidden from easy view when you are standing back and looking at the bike. 6. Clean each area where you choose to place a motorcycle LED light with the alcohol based cleaner making sure all dirt and/or oil is removed from that area

Twin Tec Installation Instructions for TC88A-IH Ignition

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
INSTALLATION ON 2004 MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 2 and 3 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. Refer to the terminal list. Crimp new Deutsch terminals on the wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 5. Install the new TC88A-IH module. 6. Reconnect the battery ground cable. INSTALLATION ON 2005 AND LATER MODELS 1. Turn off the ignition switch and disconnect the battery ground cable before proceeding. 2. Refer to Figures 4 and 5 for wiring details. 3. Remove the Gill Module. 4. Cut off the OE 18 terminal AMP connector used with the Gill module. 5. The crankshaft position (CKP), MAP, and engine temperature (ET) sensor share a common ground Daytona Twin Tec LLC, 933 Beville Road, Suite 101-H, S. Daytona, FL 32119 TC88A-IH (386) 304-0700 www.daytona-twintec.com 10/2009 Page 2 return. This is not compatible with the TC88A-IH and some rewiring will be required. The temperature sensor is not used, but does not require removal. 6. Trace the BK/GN ground return wires from terminal B of the ET sensor and terminal A of the MAP sensor to where they join the BK/GY ground return wire from the CKP sensor. Cut the ET and MAP sensor ground return wires off at this point. You can tape up the ground return wire from the ET sensor – this wire will not be used. 7. Extend the ground return wire from terminal A of the MAP sensor up to the ignition module, crimp on a Deutsch terminal and install in position 4 on the Deutsch connector. 8. Refer to the terminal list. Crimp new Deutsch terminals on the remaining wires, and install into the 12 terminal Deutsch connector required by the TC88A-IH module. 9. Use a DVM to verify isolation (no continuity) between terminals 4 and 9 on the Deutsch connector. 10. Verify continuity between terminal A at the MAP sensor and terminal 4 on the Deutsch connector. 11. Verify continuity between terminal 2 at the CKP sensor and terminal 9 on the on the Deutsch connector. 12. Install the new TC88A-IH module. 13. Reconnect the battery ground cable. Terminal List for American IronHorse´âĺ Ignition Conversion TC88A Deutsch Connector OE AMP Connector Signal Wire Color Code 1 2 +12V Power W/R

Incoming search terms: