SUZUKI SV650 Fl SYSTEM DIAGNOSIS SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
PRECAUTIONS IN SERVICING When handling the component parts or servicing the FI system, observe the following points for the safety of the system . ELECTRICAL PARTS CONNECTOR/COUPLER • * When connecting a connector, be sure to push it in until a click is felt. •With a lock type coupler, be sure to release the lock when isconnecting, and push it in fully till the works when connecting it. • * When disconnecting the coupler, be sure to hold the coupler body and do not pull the lead wires . • * Inspect each terminal on the connector/coupler for looseness or bending. • * Inspect each terminal for corrosion and contamination. The terminals must be clean and free of any foreign material which could impede proper terminal contact . •Inspect each lead wire circuit for poor connection by shaking it by hand lightly. If any abnormal condition is found, repair or replace. •When taking measurements at electrical connectors using a tester probe, be sure to insert the probe from the wire harness side (backside) of the connector/coupler . 0 4 40 O/ 40 16~ Id •When connecting meter probe from the terminal side of the coupler (connection from harness side not being possible), use extra care not to force and cause the male terminal to bend or the female terminal to open . Connect the probe as shown to avoid opening of female ter- minal. Never push in the probe where male terminal is supposed to fit. •Check the male connector for bend and female connector for excessive opening. Also check the coupler for locking (looseness), corrosion, dust, etc . FUSE • * When a fuse blows, always investigate the cause correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . ECMNARIOUS SENSORS •Since each component is a high-precision part, great care should be taken not to apply any sharp impacts during removal and installation. • * Be careful not to touch the electrical terminals of the ECM . The static electricity from your body may damage this part . FI SYSTEM DIAGNOSIS 4-3
4-4 FI SYSTEM DIAGNOSIS • When disconnecting and connecting the ECM, make sure to turn OFF the ignition switch, or electronic parts may get dam- aged. • * Battery connection in reverse polarity is strictly prohibited . Such a wrong connection will damage the components of the FI system instantly when reverse power is applied . • * Removing any battery terminal of a running engine is strictly prohibited. The moment such removal is made, damaging counter electromotive force will be applied to the ECM which may result in serious damage.

2003 SUZUKI SV 1000 Service Manual

0

Filed Under (Suzuki) by admin on 26-02-2011

download
HOW TO USE THIS MANUAL TO LOCATE WHAT YOU ARE LOOKING FOR : 1. The text of this manual is divided into sections . 2. The section titles are listed in the GROUP INDEX . 3 . Holding the manual as shown at the right will allow you to find the first page of the section easily . 4. The contents are listed on the first page of each section to help you find the item and page you need . COMPONENT PARTS AND WORK TO BE DONE Under the name of each system or unit, is its exploded view . Work instructions and other service information such as the tightening torque, lubricating points and locking agent points, are provided . Example: Front wheel SYMBOL Listed in the table below are the symbols indicating instructions and other information necessary for servicing. ENGINE OIL SUZUKIrecommends the use of SUZUKI PERFORMANCE 4 MOTOR OIL or an oil which is rated SF or SG under the API (American Petroleum Institute) service classification. The recommended viscosity is SAE 1 OW-40 . If an SAE 1 OW-40 oil is not available, select an altematice according to the right chart . BRAKE FLUID Specification and classification: DOT 4 A WARNING Since the brake system of this motorcycle is filled with a glycol-based brake fluid by the manufacturer, do not use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system, otherwise serious damage will result . Do not use any brake fluid taken from old or used or unsealed containers . Never re-use brake fluid left over from a previous servicing, which has been stored for a long period. FRONT FORK OIL Use fork oil L01 or an equivalent fork oil . GENERAL INFORMATION 1-5 ENGINE COOLANT Use an anti-freeze/engine coolant compatible with an aluminum radiator, mixed with distilled water only . WATER FOR MIXING Use distilled water only . Water other than distilled water can corrode and clog the aluminum radiator . ANTI-FREEZE/ENGINE COOLANT The engine coolant perform as a corrosion and rust inhibitor as well as anti-freeze . Therefore, the engine coolant should be used at all times even though the atmospheric temperature in your area does not go down to freezing point. Suzuki recommends the use of SUZUKI COOLANT anti-freeze/engine coolant. If this is not available, use an equivalent which is compatible with an aluminum radiator . LIQUID AMOUNT OF WATER/ENGINE COOLANT

Incoming search terms:

Moto Guzzi Breva V1100 Repair Manual

0

Filed Under (Moto Guzzi) by admin on 18-11-2010

download
1.2. GENERAL RULES 1.2.1. BASIC SAFETY RULES CARBON MONOXIDE When an operation must be performed with the engine running, position the motorcycle outdoors in a well-ventilated area. Never run the engine in an enclosed place. Use an exhaust emission extraction system when working indoors. DANGER Exhaust gases contain carbon monoxide, a poisonous gas which, if inhaled, may cause loss of consciousness or even death. FUEL DANGER The fuel used to operate engines is highly flammable and becomes explosive under particular conditions. Refueling and maintenance operations should be carried out in a well-ventilated area, with the engine off. Do not smoke when refueling or in the proximity of sources of fuel vapors. Avoid contact with bare flames, sources of sparks and any other source which may ignite fuel or lead to explosion. DO NOT DISPOSE OF FUEL IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. HOT COMPONENT PARTS The engine and exhaust component parts become hot when the engine is running and will stay hot for some time after the engine has been stopped. Wear insulating gloves before handling these components or allow for the engine and the exhaust system to cool down before proceeding. USED GEARBOX AND FORK FLUIDS DANGER Wear latex gloves when servicing. Prolonged or repeated contact with gear fluid may cause severe skin damage. Wash your hands thoroughly after handling. Dispose of it through the nearest waste oil reclamation firm or through the supplier. Wear latex gloves when servicing. DO NOT DISPOSE OF FLUID IN THE ENVIRONMENT. KEEP AWAY FROM CHILDREN. BRAKE FLUID WARNING Brake fluid can damage plastic, rubber or painted parts. When servicing the brake system, protect all such parts with a clean cloth. Always wear safety glasses when servicing the brake system. Brake fluid is highly irritant. Avoid contact with the eyes. In case of contact with the eyes, rinse abundantly with cool, clean water and immediately seek medical attention. KEEP AWAY FROM CHILDREN