SUZUKI SV650 Fl SYSTEM DIAGNOSIS SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
PRECAUTIONS IN SERVICING When handling the component parts or servicing the FI system, observe the following points for the safety of the system . ELECTRICAL PARTS CONNECTOR/COUPLER • * When connecting a connector, be sure to push it in until a click is felt. •With a lock type coupler, be sure to release the lock when isconnecting, and push it in fully till the works when connecting it. • * When disconnecting the coupler, be sure to hold the coupler body and do not pull the lead wires . • * Inspect each terminal on the connector/coupler for looseness or bending. • * Inspect each terminal for corrosion and contamination. The terminals must be clean and free of any foreign material which could impede proper terminal contact . •Inspect each lead wire circuit for poor connection by shaking it by hand lightly. If any abnormal condition is found, repair or replace. •When taking measurements at electrical connectors using a tester probe, be sure to insert the probe from the wire harness side (backside) of the connector/coupler . 0 4 40 O/ 40 16~ Id •When connecting meter probe from the terminal side of the coupler (connection from harness side not being possible), use extra care not to force and cause the male terminal to bend or the female terminal to open . Connect the probe as shown to avoid opening of female ter- minal. Never push in the probe where male terminal is supposed to fit. •Check the male connector for bend and female connector for excessive opening. Also check the coupler for locking (looseness), corrosion, dust, etc . FUSE • * When a fuse blows, always investigate the cause correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . ECMNARIOUS SENSORS •Since each component is a high-precision part, great care should be taken not to apply any sharp impacts during removal and installation. • * Be careful not to touch the electrical terminals of the ECM . The static electricity from your body may damage this part . FI SYSTEM DIAGNOSIS 4-3
4-4 FI SYSTEM DIAGNOSIS • When disconnecting and connecting the ECM, make sure to turn OFF the ignition switch, or electronic parts may get dam- aged. • * Battery connection in reverse polarity is strictly prohibited . Such a wrong connection will damage the components of the FI system instantly when reverse power is applied . • * Removing any battery terminal of a running engine is strictly prohibited. The moment such removal is made, damaging counter electromotive force will be applied to the ECM which may result in serious damage.

SUZUKI SV1000 ELECTRICAL SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COUPLER •With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. (C” -78-14) • * Bend the clamp properly so that the wire harness is clamped securely . • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . ELECTRICAL SYSTEM 7- 3 7-4 ELECTRICAL SYSTEM BATTERY •The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. • Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE HARNESS ROUTING” section. (CJ8-14)

Incoming search terms:

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.

Incoming search terms:

Baja SC50 SCOOTER OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
Engine oil level a) Check for leaks b) Tighten filler cap securely. c) Add oil if required. 2. Fuel level a) Add fuel as necessary. b) Do not overfill (no fuel in the filler neck). c) Do not mix oil with gas. d) Replace cap tightly. e) Do not refuel a hot engine. Allow engine to cool before adding fuel. 3. Warning decals a) Make sure all warning decals are legible and securely attached. b) Replace as necessary. 4. Tires a) Ensure that both tires have at least 1/8 in. tread depth at center. b) Both tires must be inflated to the pressure indicated on the tire sidewalls. c) Replace the tires id tread height is less then 1/8 in. at the center of tires. 5. Drive chain a) Check condition and tension. b) Lubricate and adjust tension as necessary. 6. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle. b) Check for frayed cable or damaged cable housing. Replace damaged cable. c) Check for mud, debris and ice in the throttle cable/mechanism. Clean out any contamination.