HONDA CB90OC/ CB900F FUEL SYSTEM AND ENGINE REMOVAL/ INSTALLATION

0

Filed Under (Honda) by admin on 05-11-2011

download
Use geniune HONDA or HONDA-recommended parts and lubricants or their equivalent. Parts that do not meet HONDA’s design specifications may damage the motorcycle. 2. Use the special tools designed for this product. 3. Use only metric tools when servicing this motorcycle. Metric bolts, nuts, and screws are not interchangeable with English fasteners. The use of incorrect tools and fasteners may damage the motorcycle.4. Install new gaskets, O-rings, cotter pins, lock plates, etc. when reassembling. 5. When ightening bolts or nuts, begin with larger­díameter or inner bolts first, and tighten to the specified torque diagonally, unless a particular sequence is specified. 6. Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before reassembly.7. After reassembly, check all parts for proper installation and operation

YAMAHA XVS 650AK (C) SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
IMPORTANT INFORMATION N 300-008 300-016 EB101000 IMPORTANT INFORMATION PREPARATION FOR REMOVAL PROCEDURES 1.Remove all dirt, mud, dust and foreign material before removal and disassembly. 2.Use proper tools and cleaning equipment. Refer to the “SPEClAL TOOLS” section. 3.When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4.During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assem~ bly and allow for the correct installation of all parts. 5.Keep all parts away f REPLACEMENT PARTS 1.Use only genuine Yamaha parts for all replacements. Use oil and grease recom- mended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. E8101020 GASKETS, OIL SEALS AND O-RINGS 1.Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2.Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips. Page 18 IMPORTANT INFORMATION I 1 T33? WASHERS/PLATES AND COTTER PINS BEARINGS AND OIL SEALS 1.lnstall bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, apply a light coating of  lightweight lithium base grease to the seal lips. Oil bearings liberally when installing, if appropriate. (D Oil seal Do not use compressed air to spin the bear ings dry. This will damage the bearing sur faces. (D Bearing

2002 YAMAHA BT 1100 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 29-11-2010

download
1. Remove all dirt, mud, dust and foreign material before removal and disassembly. 2. Use proper tools and cleaning equipment. Refer to the “SPECIALTOOLS” section. 3. When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire. EB101010 REPLACEMENT PARTS 1. Use only genuine Yamaha parts for all replacements. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. EB101020 GASKETS, OIL SEALS AND O-RINGS 1. Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips.
GEN INFO IMPORTANT INFORMATION 1-3 EB101030 LOCK WASHERS/PLATES AND COTTER PINS 1. Replace all lock washers/plates 1and cotter pins after removal. Bend lock tabs along the bolt or nut flats after the bolt or nut has been tightened to specification. EB101040 BEARINGS AND OIL SEALS 1. Install bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, apply a light coating of lightweight lithium base grease to the seal lips. Oil bearings liberally when installing, if appropriate. 1Oil seal Do not use compressed air to spin the bearings dry. This will damage the bearing sur- faces. 1Bearing CAUTION: EB101050 CIRCLIPS 1. Check all circlips carefully before reassembly. Always replace piston pin clips after one use. Replace distorted circlips. When installing a circlip 1, make sure that the sharp-edged corner 2is positioned opposite the thrust 3 it receives. See sectional view

Incoming search terms:

YAMAHA YW50X SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
1. Before removal and disassembly, remove all dirt, mud, dust and foreign material. 2. Use only the proper tools and cleaning equipment. Refer to the “SPECIAL TOOLS”. 3. When disassembling, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During disassembly, clean all of the parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire. EAS00021 REPLACEMENT PARTS Use only genuine Yamaha parts for all replacements. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. EAS00022 GASKETS, OIL SEALS AND O-RINGS 1. When overhauling the engine, replace all gaskets, seals and O-rings. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. During reassembly, properly oil all mating parts and bearings and lubricate the oil seal lips with grease.
1-3 GEN INFO IMPORTANT INFORMATION EAS00023 LOCK WASHERS/PLATES AND COTTER PINS After removal, replace all lock washers/plates 1 and cotter pins. After the bolt or nut has been tightened to specification, bend the lock tabs along a flat of the bolt or nut. EAS00024 BEARINGS AND OIL SEALS Install bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, lubricate the oil seal lips with a light coat of lithium-soap-based grease. Oil bearings liberally when installing, if appropriate. 1 Oil seal c C Do not spin the bearing with compressed air because this will damage the bearing surfaces. 1 Bearing

YAMAHA XJR1300 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 21-11-2010

download
LOCK WASHERS/PLATES AND COTTER PINS After removal, replace all lock washers/plates 1 and cotter pins. After the bolt or nut has been tightened to specification, bend the lock washer tabs and the cotter pin ends along a flat of the bolt or nut. EAS00024 BEARINGS AND OIL SEALS 1. Install bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, lubricate the oil seal lips with a light coat of lithium soap base grease. Oil bearings liberally when installing, if appropriate. 1 Oil seal Do not spin the bearing with compressed air because this will damage the bearing sur- faces. 1 Bearing EAS00025 CIRCLIPS Before reassembly, check all circlips carefully and replace damaged or distorted circlips. Always replace piston pin clips after one use. When installing a circlip 1, make sure that the sharp-edged corner 2 is positioned opposite the thrust 3 that the circlip receives. 4 Shaft 1-4 GEN INFO CHECKING THE CONNECTIONS NOTE: NOTE: NOTE: EAS00026 CHECKING THE CONNECTIONS Check the leads, couplers, and connectors for stains, rust, moisture, etc. 1. Disconnect: lead coupler connector 2. Check: lead coupler connector Moisture Dry with an air blower. Rust/stains Connect and disconnect several times. 3. Check: all connections Loose connection Connect properly. If the pin 1 on the terminal is flattened, bend it up. 4. Connect: lead coupler connector Make sure that all connections are tight. 5. Check: continuity (with a pocket tester) Pocket tester 90890-03112 If there is no continuity, clean the terminals. When checking the wire harness, perform steps (1) to (3). As a quick remedy, use a contact revitalizer available at most part stores

1999 Yamaha XVS1100 (L) DragStar Service Manual

0

Filed Under (Yamaha) by admin on 21-11-2010

download
PREPARATION FOR REMOVAL PROCE- DURES 1. Remove all dirt, mud, dust and foreign material before removal and disassembly. 2. Use proper tools and cleaning equipment. Refer to the “SPECIAL TOOLS” section. 3. When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire GASKETS, OIL SEALS AND O-RINGS 1. Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips LOCK WASHERS/PLATES AND COTTER PINS 1. Replace all lock washers/plates 1 and cotter pins after removal. Bend lock tabs along the bolt or nut flats after the bolt or nut has been tightened to specification. EB101040 BEARINGS AND OIL SEALS 1. Install bearings and oil seals so that the manufacturer’s marks or numbers are visible. When installing oil seals, apply a light coating of lightweight lithium base grease to the seal lips. Oil bearings liberally when installing, if appropriate. 1 Oil seal

Incoming search terms:

YAMAHA XVS1100 (L) SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 07-11-2010

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EB100010 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head. MODEL LABEL The model label 1 is affixed to the frame. This information will be needed to order spare parts. 1-2 IMPORTANT INFORMATION GEN INFO EB101000 IMPORTANT INFORMATION PREPARATION FOR REMOVAL PROCE- DURES 1. Remove all dirt, mud, dust and foreign material before removal and disassembly. 2. Use proper tools and cleaning equipment. Refer to the “SPECIAL TOOLS” section. 3. When disassembling the machine, always keep mated parts together. This includes gears, cylinders, pistons and other parts that have been “mated” through normal wear. Mated parts must always be reused or replaced as an assembly. 4. During machine disassembly, clean all parts and place them in trays in the order of disassembly. This will speed up assembly and allow for the correct installation of all parts. 5. Keep all parts away from any source of fire. EB101010 REPLACEMENT PARTS 1. Use only genuine Yamaha parts for all replacements. Use oil and grease recommended by Yamaha for all lubrication jobs. Other brands may be similar in function and appearance, but inferior in quality. EB101020 GASKETS, OIL SEALS AND O-RINGS 1. Replace all gaskets, seals and O-rings when overhauling the engine. All gasket surfaces, oil seal lips and O-rings must be cleaned. 2. Properly oil all mating parts and bearings during reassembly. Apply grease to the oil seal lips. 1-3 IMPORTANT INFORMATION GEN INFO CAUTION: EB101030 LOCK WASHERS/PLATES AND COTTER PINS 1. Replace all lock washers/plates 1 and cotter pins after removal. Bend lock tabs along the bolt or nut flats after the bolt or nut has been tightened to specification

Incoming search terms: