Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ΒΌ” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms: