HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE BILLET CAM SUPPORT PLATE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL NOTE For removal, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove the Maxi® fuse. 2. Remove the cam cover and gasket. 3. Remove and discard the crank and primary cam sprocket flange bolts and washers. 4. Release the oil pump, and remove the cam support plate and cams. Disassemble the cams from the support plate and discard the support plate. 5. Inspect cams, chain, sprockets, oil pump, chain tensioners and guide for wear and replace as needed. Refer to the Service Manual for inspection and replacement proce- dures. -J04503 INSTALLATION NOTES For installation, refer to the appropriate sections of the applicable Service Manual for detailed information on the following generalized steps. See Figure 1. When installing Screamin’ Eagle camshaft kits, install the O-ring included in this kit over the splined shaft of the rear camshaft as shown. 1. Using the Camshaft Assembly Tool (HD-47956) and assemble the camshafts, chains and tensioners to the billet cam support plate. 2. Install the cam support plate assembly into the crankcase. 3. Using the Crankshaft/Camshaft Locking Tool (HD-47941), install cam sprockets, chain and tensioner. 4. Install cam cover and gasket. 5. Install Maxi fuse.

Incoming search terms:

HARLEY DAVIDSON FLHT OIL PRESSURE AND AIR TEMPERATURE GAUGE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
INSTALLATION Oil Pressure Sending Unit To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. 1 2 3 4 is04574 1. Oil pressure sending unit 2. Cam position sensor 3. Crank position sensor 4. Main harness to ECM Figure 1. Electrical Bracket: 2000-2001 Fuel Injected Models (Magnetti-Marelli) 1 2 3 is04575 1. Oil pressure sending unit 2. Crankshaft position sensor 3. P&A siren kit Figure 2. Electrical Bracket (ECM Removed) 2002-2003 Fuel Injected Models (Delphi) -J01875 1 of 4 NOTE For 2002 to 2003 models: See Figure 2. Remove the two screws securing the ECM and remove the ECM to access the electrical bracket. 2. For 2004 and later models: Proceed to the Gauges section. For 2000 to 2003 models: See Figure 1, Figure 2 and Figure 3 for the applicable model and locate the sensor harness connector (2-piece mini-Deutsch® connector). 3 2 4 1 is04576 1. Ignition harness 2. Cam position sensor 3. Oil pressure sending unit 4. Crankshaft position sensor Figure 3. Ignition Module – Carbureted Models 3. Locate the oil pressure sending unit at the front right side of the crankcase and pull wire socket from terminal of the oil pressure sending unit. 4. Carefully draw the conduit and the pin side of mini-Deutsch connector forward and then up between the rear brake master cylinder reservoir and the frame downtube to area of the rear brake pedal. 5. See Figure 4. Remove the secondary locking wedge (3) from the pin side of the connector with a needle nose pliers. 1 3 2 is04577 1. Pin 2. Wire seal 3. Locking wedge Figure 4. Deutsch Connector Pin Side (2-pin connector shown) 6. Gently depress terminal latches inside pin housing and back out the pin in chamber #1 through the hole in wire seal. 7. Pull the oil sending unit wire through conduit and remove wire. Note the routing of the wire. 8. See Figure 9. Route the jumper (6) pins through the conduit from the kit in the same direction as the original wire noted in Step 7. Use cable straps to secure to the wire bundle. 9. See Figure 5. Locate pin chambers #1 and #2 on pin side of connector. Insert brown/green jumper pin into chamber #2 and feed until it clicks into place. Verify that pin will not back out of the chamber by giving a slight tug on the wire to confirm that it is locked

Incoming search terms: