1988 – 1995 V6 Truck, 4Runner 3VZ CYLINDER HEAD INSTALLATION and REMOVAL

0

Filed Under (Toyota Manuals) by admin on 06-12-2011

download
Install cylinder head a. Place a new cylinder head gasket on the engine block and install cylinder head. b. Apply a light coat of engine oil on the threads and washer face of the cylinder head bolts. c. Install the plate washer to the cylinder head bolt. d. Using a 12-point socket, install and uniformly tighten the (8) 12-point bolts in several passes, in the sequence shown in the illustration. Torque: 33 ft.lbs. (44 N-m, 450 kg-cm) e. Repeat for the other head. 2. Proceed with final tightening sequences: a. Mark the front side of the top of the bolt with a drop of paint as shown in the illustration

Incoming search terms:

BMW K1100LT/ RS Repair Manual

0

Filed Under (BMW) by admin on 03-12-2010

download
00.3 00 Tightening torque Model K 1100 LT K 1100 RS Connection Nm 11 Engine Freewheel Cover plate/freewheel cage at countershaft gear 10 Oil – water pump Oil pressure switch 40 Temperature sensor/screw plug 9 Pressure relief valve 40 Impeller 33 Pump housing to crankcase 10 Cover to pump housing 10 (3-Bond 1209) Intermediate flange Thrust plate at intermediate flange 9 (Loctite 243) Intermediate flange at crankcase 9 Crankshaft Pinion/rotor flange at crankshaft 50 Main bearing cap to crankcase 50 Connecting rod Big end cap Wrench angle 80 ° 30 Input shaft Front bearing 18 Rear bearing 40 Engine block Crankshaft cover 9 Lower part, outer 10 Oil sump 10 Oil filter cover 10 Oil drain plug 30 Cylinder head Cylinder head bolts (SI 11 062 95 (697) Short thread (from 6/93 to 11/94): Wrench angle, 1st stage Wrench angle, 2nd stage Long thread (since 12/94): Wrench angle, 1st stage Wrench angle, 2nd stage 64° 42° 75° 75° 22 20 Cylinder head cover 9 Camshaft Bearing cap 9 (Apply a thin coat of 3-Bond 1209 only at corners and butt edges) Chain sprockets 54 00.4 Timing chain Chain tensioner 9 Slide rail at camshaft bearing cap 9 Timing case cover Timing case cover 10 (3-Bond 1209) Cover for Hall-effect signal transmitter 9 Screw plug 40 Clutch Clutch housing to output shaft Tighten to Release and re-tighten to Wrench angle 50° 140 50 Housing cover 19 Alternator Alternator to intermediate flange 22 Driver 33 Starter motor Starter motor to gearbox 9 Mixture preparation Intake stub pipe 9 Fuel injection rail 9 Cooling system Coolant stub pipe at cylinder head 9 Temperature sensor at coolant stub pipe 30 Air cleaner Lower part of air cleaner housing 21 12 Engine electrical system Starter to transmission 9 Positive lead to starter 5 Alternator to intermediate flange 22 Clutch housing 50 Base plate 3,5 Setting ring 2,5 Hall generator cover 9 Ignition coils to intermediate flange 5 Spark plug 20 Model K 1100 LT K 1100 RS Connection Nm 00.5 13 Fuel preparation and control Injection rail 9 Intake stub pipe 9 Lower section of air cleaner housing 21 Intake air line 9 Motronic control unit 5 17 Radiator Connecting screw, temperature sensor 9 Fastening, thermostat cover 3 Radiator to frame 9 Coolant stub pipe to cylinder head 9 (with Loctite 243) Temperature sensor to coolant stub pipe 30 18 Exhaust System Exhaust system to cylinder head 21 Front silencer (muffler) 12 Exhaust system holder to footrest plate 33 Exhaust system to holder/footrest plate 9 Retaining bracket to gearbox 41 Oxygen sensor Hand-tight 21 Clutch Clutch housing to output shaft tighten to loosen and retighten to tightening angle 50° 140 50 Housing cover

Incoming search terms: