HArley Davidson Sportster Sideshots Exhaust system Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Remove the two bolts from each muffler body which Page 1 of 4 D465IN Rev. 1.0 Sportster Sideshots Exhaust system Part #26011 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: Wrenches – 9/16″ and 1/2″ Ratchet, 3/8″ drive and 9″ extension Torx sockets – T30 Sockets – 9/16″ and 1/2″ 3/16″ & 5/16″ Allen wrench 5/16″Nutdriver/flat blade screwdriver Snapring pliers attach the muffler bodies to the mounting bar and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. Note: If circlips look bent or twisted replace them with new circlips.

Harley-Davidson DYNA Straightshot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Remove any studs and bolts necessary and set aside to use when installing the new muffler mounting bar to the transmission housing. Refer to figure 1. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Check condition of stock exhaust gaskets. Replace if worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets, part number 17048-98. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Slide one pipe clamp (supplied) onto the front head pipe. Position the clamp in the approximate location on the tube where it mounts to the engine. 5. Slide one pipe clamp (supplied) onto the rear head pipe. Position the clamp in the approximate location on the tube where it mounts to the top hole in the mounting bar bracket. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike

DRAK AIR FILTER KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 21-12-2010

download
1. Take off the Air fi lter cover by removing the Button head cap screw in the center. 2. Removed the fi lter element by taking out the three exposed Torx head cap screws. 3. Remove the breather hoses from the Cylinder head breather bolts by pulling on them. 4. Remove the three Bolts that secure the Backing plate to the Carburetor / Throttle body and the two Breather bolts that secure it to the Cylinder heads. 5. Remove the Backing plate and Gasket, on FI models the wiring mount clip should be carefully pulled out of the plastic housing. NOTE: Be sure that the gasket surface is clean and dry and that no gasket material remains stuck to it. 6. None of the OEM parts will be reused for this installation 1. For a clear understanding of this installation it is best to refer to the exploded view diagram while reading these instructions. 2. When installing or servicing the air cleaner, apply Loctite 243 (blue) to threads of all fasteners. 3. Loosely install the gasket (1) and carburetor / throttle body mount bracket (2) using the two cylinder head breather bolts (3) and cylinder head O-rings (4) NOTE: Make sure the gasket is installed in the correct rotation and right side up. The slightly smaller bleed hole should be in the top left hand corner. 4. Using the three 1/4″-20 x 1″ socket head cap screws (5) install the fi lter backing

Harley Davidson Softail Sideshots Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 20-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. On FLSTN, FLSTF, FLSTH and FLSTC loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heat shield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (Not necessary on 2000- up models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head 5. Remove the bolts attaching the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. On pre 2000 models go to step #9, on 2000-up models go to step #10. 9. Remove the right passenger foot peg bolt. Position the motorcycle on the side stand with a floor jack under the swing arm pivot bolt on the right hand side. Raise the jack just enough to take the weight off the pivot bolt, remove the bolt and stock mounting bar. Reinstall the pivot bolt and torque to 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″ x 3″ Allen bolt and 1-5/8″ length spacer (supplied). 10. Using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″ x 2 1/2″ Allen bolt and 3/4″ length spacer (supplied). 11. The bolts and spacers used in the above steps may also be used on all Softail models to space the right rear foot peg away from the exhaust. 12. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers (save for reuse). NOTE: If circlips look bent or twisted replace them with new circlips.

SUZUKI VZ800 MARAUDER SLIP-ON EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosenthe right hand side footrest assembly. 2. Loosenthe two head pipes at the cylinder head. 3. Loosen the muffler clamps, located on the inlet end of the mufflers. 4. Remove the two nuts that mount the lower muffler to motorcycle. Keep the two mufflers bolted together as an assembly. 5. Lift the muffler assembly up to clear the studs from the mounting holes. Pull the mufflers off the head pipes and set them aside. 6. Remove the two flanged steel spacers from the hole in the rubber cushions, where the stock muffler assembly mounted. Reinstall the steel spacers through the backside of the rubber cushions so the flanged end of the spacers are on the backside of the cushions, opposite of there original position. 7. Remove the rear most heat shields from both of the head pipes and set them aside. 8. Remove the stock exhaust gaskets from the ends of both pipes. The Vance & Hines slip-on does not use a gasket at the slip joint . 9. Install the new muffler mounting bracket (stamped with the # 233 ) to the front side of the two holes with the rubber cushions the two of the 5/16″x 1 1/4″ bolt and two 5/16″ lock nuts (hardware supplied) through the two holes in the bracket that are spaced farthest apart. When mounted correctly, the bracket should bend up and out from the motorcycle

Incoming search terms:

YAMAHA YZ250F ALUMINUM PRO SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING YOUR STOCK SYSTEM 1. Place the machine on a stable work stand. 2. If you are not familiar with removing the original exhaust refer to the owner’s manual before you start work. 3. Always allow your machine to cool down before attempting to remove the exhaust. 4. Remove the two bolts from the right side panel. Then remove the side panel. 5. Loosen the stock mid-pipe clamp, then remove the stand-off bolt and bracket bolt that supports the muffl er. 6. Remove stock muffl er and clamp from the stock head pipe. 7. Remove the stock head pipe at the cylinder head. NOTE: It may be necessary to use a penetrating lubricant on the fl ange nuts. INSTALLING THE NEW ALUMINUM PRO SYSTEM 1. Install Aluminum Pro head pipe onto cylinder head using stock nuts. Leave these fi nger tight for now. 2. Slide mid-pipe onto head pipe. Rotate the mid-pipe slightly to obtain proper alignment with sub-frame mount. 3. Install the OEM bolt through sub-frame into the stand-off mount on mid- pipe (Finger tight). 4. Slide the muffl er onto mid-pipe, align muffl er mount with the stock muffl er mount hole, and install and fi nger tighten the supplied M8x25mm bolt. 5. Once you have the system fully aligned, tighten all the bolts securely to factory specifi cations. NOTE: We recommend starting at the cylinder head and working backwards. 6. Replace the side panel and secure the mounting bolts. BEFORE YOU BEGIN MORE

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms:

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite┬« 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

YAMAHA V-STAR 650 EXHAUST SYSTEM REMOVAL AND INSTALLATION

0

Filed Under (Yamaha) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the right hand frame cover to avoid scratching it. 2. Remove the nuts that mount the rear header to the cylinder head. 3. Loosen the pinch clamp on the inlet end of the lower muffler. 4. Remove the two bolts that mount the mufflers to the muffler bracket, located between the two mufflers. Save the hardware for reuse. 5. Pull the rear head pipe out of the exhaust port. Slide the muffler assembly with the rear head pipe attached, rearward, disconnecting it from the front head pipe. Set the assembly aside. Note: Keep the front head pipe attached to the motorcycle, it will integrated with the new exhaust system. 6. Remove the muffler mounting bracket from the frame and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the V&H muffler mounting bracket (stamped 272) to the frame using the stock hardware and mounting location. Refer to figure 1 2. Slip the T-bolt band clamp (supplied) over the straight pipe that is welded to the front muffler. 3. Slip the front muffler assembly over the stock head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 4. Install the rear header assembly to the exhaust port using the stock 8mm nuts, but leave them loose at this time. 5. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the rear muffler. Attach the muffler to the mounting bracket using two of the 5/16″ flange head bolts (supplied), but leave them loose at this time. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 7. Align the mufflers so they are parallel when viewing from the right side of the bike, and tighten the 5/16″ flange bolts on the back side of both mufflers. 8. Tighten the two header flange nuts on the rear head pipe. 9. Tighten the T-bolt clamp at the slip joint of the front muffler. 10. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. Note: The edge of the heat shield should just cover the weld on the inlet of each muffler, if not, adjust the heat shield for correct alignment

BUELL BLAST SS2-R Exhaust System Removal And Installation

0

Filed Under (Tips and Review) by admin on 18-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two nuts that mount the header to the cylinder head. 2. Remove the rear muffler mounting bolts. Remove the bolt from the insulated mount at the front of the muffler. Save the nuts and bolts for reuse. 3. Remove the stock head pipe and muffler assembly. 4. Using circlip pliers carefully remove the circlip and flange from the stock exhaust system.Save for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Slide the circlip and flange over the VHR head pipe. NOTE: If the circlip looks bent or twisted replace it with a new circlip. 2. Slide the supplied clamp over the head pipe. 3. Install the head pipe into the exhaust port using the stock flange nuts. Leave finger tight at this time. 4. Bolt the head pipe clamp to the engine using the supplied bracket stamped #311. Refer to Fig. 1for the assembly order of the front mounting hardware. Leave loose at this time. 5. Slide the supplied clamp onto the notched end of the muffler assembly. 6. Slip the muffler assembly onto the head pipe. Bolt the muffler assembly to the original mounting points at the rear of the frame, using the supplied 5/16″-18×3/4″ socket head capscrews, stock nuts and washers. 7. Tighten the exhaust flange nuts and muffler clamp. 8. Tighten the two bolts that mount the muffler assembly to the motorcycle. 9. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications